SPM 05 ENvFIN.indd - Salomon Certification

More documents

Recommendations

Info

Reference 9 # 001156 Jig Selection & Use # 000893 Drill Bit Diameter 4.1 x 9.5 # 887623 Universal Jig # 887762 Poweraxe Mounting Kit 18 POWERAXE RACE PLATES Poweraxe/Pilot Race GS Plates To be mounted by a Salomon Authorized Dealer only; not compatible with junior skis A S D F a Product description 2 platforms, 4 bails, 2 distributors, 2 axle/screw subunits and 4 transmitter pads Tools needed for mounting Mounting the plate on the skis Universal plate jig (Ref. 887623), Poweraxe mounting kit (Ref. 887762) and Drill bit diameter 4.1 x 9.5 (Ref. 000893) Mounting the bindings on the plates Jig (Ref. 001156) and Drill bit diameter 4.1 x 9.5 Drilling the skis Place the jig on the ski so the boot mid-sole mark is aligned with the middle-of-the-ski mark. Be careful when centering the jig Fig A. Attach the Poweraxe mounting kit on the universal plate. A Poweraxe Race SL Plates Select the yellow bushings on this jig, which correspond to the Poweraxe and Pilot Race GS plates. Drill the eight holes using the drill bit diameter 4.1 x 9.5 Remove the jig and shavings. Mounting the distributor and bails Place the distributor over the 8 holes drilled, with the arrow pointed towards the ski tip. Then place the bails (note: the front bail is the one that has the oblong hole). See Fig S for mounting the bail according to the boot size. Caution: When drilling the plate, if the binding holes fall where an axle is located, remove the plate, reverse the direction of the bails Fig D and repeat the mounting procedures. Not compatible with junior skis or rental bindings There are 2 sizes of Poweraxe Race SL plates: Large (for 297 mm – 356 mm boot sole lengths ) and Medium (for 259 mm – 318 mm boot sole lengths) Product description Fig A • 2 forward plate sub-units with pre-mounted screws. • 2 rear plate sub-units with pre-mounted screws. MOUNTING Caution: The retail jig is not compatible. Position the Poweraxe Race jig on the ski aligning the boot mid-sole on ‘LARGE’ or ‘MEDIUM’ according to the length of the plate selected Fig S. Drill the ski according to the ski manufacturer’s recommendations. Place the forward plate subunit on the ski and tighten the screws following this screwing pattern: first the bail, then the hood (4 Nm torque) Fig D. Place the rear plate sub-unit on the ski and insert the linkage plug into the corresponding slot on the forward plate sub-unit and tighten the screws in the following order: first the rear plate, then the bail and finally the hood (4 Nm torque) Fig F. Tighten the screws on one bail using a criss-cross pattern Fig F. Repeat the same procedure on the other bail. Mounting the platform Place the platform and transmitter pads on the ski. Place the platform on the bails starting in the rear. Insert the rear axle by tapping with a mallet and tightening the opposite screw (torque 3 – 4 Nm). Use the same procedure on the front bail. Note: It is necessary to slightly compress the transmitters to insert the axles. Mounting the bindings For these models, we recommend using the S914 FIS binding. S F According to the boot sole length selected, tighten the screws on the toe and heel pieces (4 Nm torque) in the corresponding position on the Poweraxe Race SL plate Fig G. Remove the Poweraxe mounting kit from the universal plate jig. Place the universal plate jig on the ski so it wraps around the plate. Adjust the drilling jig according to the boot sole length. Squeeze the arms of the binding jig on the rails of the universal plate jig, and place it according to the boot mid-sole mark indicated on the side of the plate. Drill the binding holes in the plate using a 4.1 x 9.5 mm diameter drill bit. Remove both jigs and the shavings. Lubricate the holes. Follow the normal procedure to mount the binding on the plate. D G Position on the MEDIUM LARGE Poweraxe Race Poweraxe SL plate Poweraxe SL plate SL plate (boot sole length) (boot sole length) Position 4 259-276 mm 297–314 mm Position 3 273-290 mm 311–328 mm Position 2 287-304 mm 325–342 mm Position 1 301-318 mm 339–356 mm b d c Mount the brake following the usual procedure. Important: Put the boot in the binding and adjust the forward pressure adjustment.
Salomon Binding Interfaces RETAIL MOUNTING SPECIAL CASES IN MOUNTING Poweraxe Race SL M/L 780460(M)/780458(L) 55 All Bindings; use with Carve Brake model # Poweraxe Race GS 888375 50 001160** All Bindings; use with Carve Brake model # Pilot Race GS 780447 50 001160** All Bindings; use with Carve Brake model # Plate Model Ref. 001160** Poweraxe Energy 2 31.2 Sold with bindings only Poweraxe Sport 33.5 Sold with bindings only Poweraxe Active 32.5 Sold with bindings only # Height/mm* Compatibility * Plate and binding ** Substitute model #78145801 when supplies of model #001160 are exhausted. Non-Indemnified Bindings Adjustment Non-Indemnified Bindings Older models of Salomon bindings no longer on the Schedule of Indemnified Bindings may still be Drive Plates & Lifters Adjustment serviced, however Liability Indemnification will not be offered by Salomon for these models of bindings. Dealers wishing to service Salomon Drive Plates & Lifters Salomon Drive Plates & Lifters (above chart) are available for Spheric Performance and Spheric Sport bindings. The plates provide extra lift between the ski and binding. Axe Plus, Drive Plus and “Ramp” versions are mounted using a Salomon Jig. (Ref. # 001156). Extended length screws are provided with the plates. Refer to the 2004/2005 Salomon Spare Parts Catalog for plate specifications. these models of bindings can reduce their liability risk by requiring an additional waiver and release agreement and attaching it to the Workshop Competition Bindings Adjustment Form. Such waivers should be reviewed by a dealer’s own legal counsel to ensure compliance with applicable laws. Salomon distributes competition bindings to racers and coaches. These bindings are intended to be used by skiers with special retention needs. If these bindings are used by recreational skiers, there is a far greater risk of injury due to the use of more powerful springs. Refer to Requested Settings for instructions for skiers requesting settings not recommended by Salomon. > Reference # 001156 Adult Retail Jig Requested Settings 19 24
Page 3 and 4: CONTENTS 2 Introduction 4 Certifica
Page 5 and 6: INTRODUCTION Salomon Systems & Bind
Page 7 and 8: Certification & Indemnification SCH
Page 9 and 10: RETAIL SYSTEMS Proper procedures fo
Page 11 and 12: A SD F G H J K Legend 1 Handle with
Page 13 and 14: A Tapping Adjustment Glue Adjustmen
Page 15 and 16: 13 12 A 14 S914 AXE+ 11 10 Mounting
Page 17 and 18: 16 17 A G 15 14 13 Mounting Powerax
Page 19: Assembly Measure boot sole length i
Page 23 and 24: Instructions Adjusting Pilot classi
Page 25 and 26: Fat Ski Brakes RETAIL MOUNTING FAT
Page 27 and 28: All current model Salomon bindings
Page 29 and 30: The Boot • Inconsistencies with I
Page 31 and 32: FINAL CHECKING TROUBLESHOOTING Boot
Page 33 and 34: FINAL CHECKING RETAIL RECORD KEEPIN
Page 35 and 36: RENTAL & DEMO SYSTEMS Proper proced
Page 37 and 38: RENTAL & DEMO MOUNTING 35
Page 39 and 40: 14 13 12 11 Mounting (continued) G
Page 41 and 42: A Toe Length Adjustment Rental Toe
Page 43 and 44: e 2 BOOTS: • Thermic Fit liner, S
Page 45 and 46: Pre-Season Binding Inspections Adju
Page 47 and 48: RENTAL & DEMO MOUNTING RENTAL SKIER
Page 49 and 50: Name: Street City Phone # Driver’
Page 51 and 52: Spheric Performance Models Procedur
Page 53 and 54: Quadrax Models - with Equalizer Pro
Page 55 and 56: Any incorrect use of a Salomon part
Page 57 and 58: Retail Guidelines Salomon bindings
Page 59 and 60: Replacement Procedures Step One. Ve
Page 61 and 62: POST ACCIDENT SKI EQUIPMENT Inspect
Page 63 and 64: Ski/Binding Maintenance Record Boot
Page 65 and 66: TECHNICAL REFERENCE 2004/2005 TECHN
Page 67 and 68: DIN scale Height in mm Skier weight

SPM 05 ENvFIN.indd - Salomon Certification

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?