HC-V100PC HC-V100PU HC-V100EB HC-V100EC - Panasonic

More documents

Recommendations

Info

10 Factory Setting 10.1. How To Turn On The Factory Settings? (CAUTION) Performing the factory settings, the built-in memory is initialized and all of recorded data are deleted. (SD memory card is not initialized by the factory settings.) 1. Set the mode switch “Recording” mode. 2. Turn the power on, and then while keep pressing the “Zoom lever” to W side, “Intelligent auto/Manual” button and “Menu” button for more than 3 seconds until the top screen of the Service Mode Menu being displayed. 3. Under the condition of the Item No. [ 1 ] is yellow high lighted , then press “ENTER” button. 4. By pressing the “[UP] or [DOWN] of cursor” button and display a highlight in a [ YES ] item, then press the “ENTER” button. 5. After few seconds “END” is displayed on LCD monitor. Press [ POWER ] button or cutting of battery connection or AC power supply connection as a completion of the “FACTORY SETTINGS”. NOTE: Do not using service mode except above table of Service mode menu. End method of the top screen of the service mode menu. Push the “MENU” button to end the service mode, and then POWER OFF. 10.2. What Is The Factory Settings? The factory settings clean up and/or refresh the following settings. 1. Physical formatting of the built-in memory. (All user recorded data are deleted) 2. MENU, MODE, ADJUSTMENT VALUE. 3. Reset the folder number and file number of still pictures. (Setting the folder number is 100, and file number is 0.) 4. Clear the service mode information contents. 5. Initialize the VIERA Link Physical Address. The setting position of factory settings: Name Setting position Mode switch Recording mode 26
10 Block Diagram 10.1. Overall Block Diagram OVERALL BLOCK DIAGRAM SHUTTER OPERATION IC2002 EEPROM DC IN BATTERY LENS(F1.8 4.0 34x) ZOOM/ FOCUS MOTOR/ OIS IRIS IC701 LENS/OIS DRIVE IC6401 GYRO SENSOR IC1503 RTC/CHARAGE/ POWER CONTROL X2303 (32.768kHz) IC201 MOS IMAGE SENSOR IC2006 SYSTEM CONTROL (CAMERA MICROCOMPUTER) IC1001 POWER IC1502 BATTERY MONITOR IC301,703,704,1011, 1421,1441,1471 REGULATOR IC511 MAGNETIC SENSOR IC202,302 GATE IC IC1501 VOLTAGE DET. IC2301 RESET USB TERMINAL X3401 OSC (48MHz) IC705 D-TYPE FLIP-FLOP X2001 OSC (13.5MHz) 27 IC3401 ASIC IC3751 VIDEO ENCODER IC3404 NAND FLASH ROM/ 512Mbit SD CARD IC3701 VIDEO AMP IC3402 DDR3 SDRAM/ 512Mbit IC3403 DDR3 SDRAM/ 512Mbit <strong>HC</strong>-V100M ONLY IC3202 INTERNAL MEMORY /16GB NOTE : VIDEO SIGNAL : AUDIO SIGNAL : CLK or CONTROL LINE COLOR LCD PANEL Analog Analog Analog Analog A/V MULTI TERMINAL ECM SPEAKER HDMI mini CONNECTOR <strong>HC</strong>-V100M/V100 OVERALL BLOCK DIAGRAM
Page 1 and 2: ORDER NO. VM1202003CE B27 High Defi
Page 3 and 4: 1 Safety Precautions 1.1. General G
Page 5 and 6: 2.3. Caution for AC Cord (For EB/GC
Page 7 and 8: 3 Service Navigation 3.1. Introduct
Page 9 and 10: 3.5. Formatting 9
Page 14 and 15: 6 Service Mode 1. Indication method
Page 16 and 17: 7 Service Fixture & Tools 7.1. When
Page 18 and 19: 8.3.1. Removal of the Top Case Unit
Page 20 and 21: Fig. D6 8.3.4. Removal of the Lens
Page 22 and 23: Fig. D11 8.3.6. Removal of the ESD
Page 24 and 25: 9 Measurements and Adjustments 9.1.
Page 28 and 29: 10.2. Camera/System Control Circuit
Page 30 and 31: 10.4. Video/Audio Signal Process(2)
Page 32 and 33: 10.6. Power Supply Circuit Block Di
Page 34 and 35: Model No. : HC-V100/V100M Schematic
Page 36 and 37: Model No. : HC-V100/V100M Main Conn
Page 38 and 39: Model No. : HC-V100/V100M HD Video
Page 40 and 41: Model No. : HC-V100/V100M Syscon (M
Page 42 and 43: Model No. : HC-V100/V100M MIC (Main
Page 44 and 45: Model No. : HC-V100/V100M MOS Conne
Page 46 and 47: Model No. : HC-V100/V100M Main P.C.
Page 48 and 49: Model No. : HC-V100/V100M SD Holder
Page 50 and 51: Model No. : HC-V100/V100M Parts Lis
Page 60 and 61: Model No. : HC-V100/V100M Packing P
Page 62: Model No. : HC-V100/V100M Parts Lis

HC-V100PC HC-V100PU HC-V100EB HC-V100EC - Panasonic

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?