INCREMENTAL ENCODER MyInc - MEYER Industrie-Electronic ...

More documents

Recommendations

Info

38 INCREMENTAL ENCODER MyInc Dimensioned drawing BINH 50 Bracket with tether arm (Bracket type T5 and T7) Bracket with stator coupling Pitch circle Ø 63 mm (Bracket type O5 and O7) O R D E R I N G C O D E BINS50 shaft BINH50 hollow shaft Shaft Ø 06 = 6 mm 10 = 10 mm 12 = 12 mm 06 = 6 mm 08 = 8 mm 10 = 10 mm 12 = 12 mm 14 = 14 mm 15 = 15 mm Meyer Industrie-Electronic GmbH – MEYLE Carl-Bosch-Straße 8 49525 Lengerich/Germany Tel.: +49 54 81-93 85-0 Fax: +49 54 81-93 85-12 BINS50 BINH50 Flange, Protection Output circuit Output Signals Connection Resolution S5 = Synchro, IP 65 (shaft) A5 = Push-pull 9 = A+B+0+Compliments 3R = shielded cable, 5000 max. S7 = Synchro, IP 67 (shaft) 5 to 30 VDC 1 m, radial output K5 = Clamping, IP 65 (shaft) A2 = Line Driver 8R = 12 pin connector, K7 = Clamping, IP 67 (shaft) 5 VDC RS 422 M23, radial output, H5 = Torque stop, IP 65 (hollow shaft) CCW H7 = Torque stop, IP 67 (hollow shaft) N5 = Stator coupling pcd 65 mm, IP 65 (hollow shaft) N7 = Stator coupling pcd 65 mm, IP 67 (hollow shaft) O5 = Stator coupling pcd 63 mm, IP 65 (hollow shaft) O7 = Stator coupling pcd 63 mm, IP 67 (hollow shaft) T5 = Tether arm, IP 65 (hollow shaft) T7 = Tether arm, IP 67 (hollow shaft) 10R = 10 pin MIL connector, radial output 12R = 8 pin connector, M12, radial output, CW Internet: www.meyle.de E-Mail: sales@meyle.de
INCREMENTAL ENCODER MyInc • Shaft (FINS) and hollow shaft (FINH) encoder with the same modular concept • Shaft diameters Ø 6 and Ø 10 mm for shafted encoders • Hollow shaft Ø 14 mm, aluminium reduction hubs of Ø 6, Ø 10 and Ø 12 mm • Robustness, excellent shock and vibrationresistance • Easily achievable high degree of protection IP 67 with special sealing flange for shafted versions • High resolutions available up to 80000 cpt in 3 channels with complements • Available output signals: square wave, square wave programmable and sine wave Replacment for GHM5, GHT5, GHK5, GHO5. • • • • • • • • • • • Simple programmable resolution through dipswitch, no software, no hardware required • Universal electronic circuits from 4.75 Vdc to 30 VDC • High operating temperature performance: -30 °C up to 100 °C (encoder temperature) • High frequency response performance of the output signals: 300 kHz (push-pull & RS422) • Glass disks in standard, available with unbreakable disks in Polyfas (Composite Mylar-Mica) in option for resolutions
Page 1 and 2: Incremental Encoder Absolute Encode
Page 3 and 4: CONTENTS SELECTION GUIDE 3 GENERAL
Page 5 and 6: SELECTION GUIDE Incremental Encoder
Page 7 and 8: SELECTION GUIDE Incremental Encoder
Page 9 and 10: GENERAL/OVERVIEW Introduction Descr
Page 11 and 12: GENERAL/OVERVIEW General Dirt/dust
Page 13 and 14: GENERAL/OVERVIEW General Selecting
Page 15 and 16: GENERAL/OVERVIEW General Digital ou
Page 17 and 18: GENERAL/OVERVIEW General Selecting
Page 19 and 20: GENERAL/OVERVIEW Interface Cable le
Page 21 and 22: GENERAL/OVERVIEW General The CANope
Page 23 and 24: GENERAL/OVERVIEW General Diagnostic
Page 25 and 26: INCREMENTAL ENCODER MyInc Terminal
Page 29 and 30: INCREMENTAL ENCODER MyInc Signal: 0
Page 33 and 34: INCREMENTAL ENCODER MyInc AINS40/AI
Page 35 and 36: INCREMENTAL ENCODER MyInc fslaklös
Page 37 and 38: INCREMENTAL ENCODER MyInc • Unive
Page 39: INCREMENTAL ENCODER MyInc Dimension
Page 45 and 46: INCREMENTAL ENCODER MyInc Connectio
Page 49 and 50: INCREMENTAL ENCODER MyInc Dimension
Page 51 and 52: INCREMENTAL ENCODER MyInc AINS912 3
Page 55 and 56: INCREMENTAL ENCODER MyInc AINH90 5R
Page 57 and 58: INCREMENTAL ENCODER MyInc ORDERING
Page 63 and 64: OVERSPEED SWITCH AOSS90 Dimensioned
Page 65 and 66: D R A W W I R E CDxx O R D E R I N
Page 67 and 68: ABSOLUTE ENCODER MyAbs CAxx37 Dimen
Page 69 and 70: ABSOLUTE ENCODER MyAbs BAxx58 Absol
Page 71 and 72: ABSOLUTE SHAFT ENCODER SINGLETURN,
Page 77 and 78: ABSOLUTE SHAFT ENCODER MULTITURN, C
Page 79 and 80: ABSOLUTE HOLLOW SHAFT ENCODER SINGL
Page 85 and 86: ABSOLUTE HOLLOW SHAFT ENCODER MULTI
Page 87 and 88: ABSOLUTE ENCODER MyAbs S S I , B i
Page 89 and 90: ABSOLUTE ENCODER MyAbs BAxx58 O R D
Page 91 and 92:
ABSOLUTE ENCODER MyAbs CAxx58 Mecha
Page 93 and 94:
ABSOLUTE ENCODER MyAbs CAxx58 Bus C
Page 95 and 96:
ABSOLUTE ENCODER MyAbs CAxx58 ORDER
Page 97 and 98:
ABSOLUTE ENCODER MyAbs Mechanical D
Page 99 and 100:
ABSOLUTE SHAFT ENCODER MULTITURN, P
Page 101 and 102:
ABSOLUTE HOLLOW SHAFT ENCODER MULTI
Page 103 and 104:
ABSOLUTE ENCODER MyAbs FAxx90 ORDER
Page 105 and 106:
MOUNTING ACCESSORIES A n t i - r o
Page 107 and 108:
MOUNTING ACCESSORIES Large choice o
Page 109 and 110:
COUPLING Large choice of couplings
Page 111 and 112:
CONNECTION ACCESSORIES Large choice
Page 113 and 114:
MEASURING ACCESSORIES Mesuring whee
Page 115 and 116:
INSTALLATION INSTRUCTIONS If possib
Page 117 and 118:
INSTALLATION INSTRUCTIONS Mounting
Page 119 and 120:
NOTES Meyer Industrie-Electronic Gm
Page 121 and 122:
Engineering, distribution and manuf
show all

INCREMENTAL ENCODER MyInc - MEYER Industrie-Electronic ...

Create successful ePaper yourself

Delete template?

Save as template?