ug585-Zynq-7000-TRM

More documents

Recommendations

Info

29.1.1 Block Diagram X-Ref Target - Figure 29-1 29.1.2 Features SCU AXI64 RdCmd SCU AXI64 WrCmd SCU AXI64 WrData OCM Switch AXI64 RdCmd OCM Switch AXI64 WrCmd OCM Switch AXI64 WrData APB I/F Key features of the OCM include: 256 KB RAM Parity Generation & Checking Arbiter 4-port Mem Controller Registers Figure 29‐1: OCM Block Diagram Chapter 29: On‐Chip Memory (OCM) SCU AXI64 RdData SCU AXI64 Bresp OCM Switch AXI64 RdData OCM Switch AXI64 Bresp UG585_c29_01_042512 • On-chip 256 KB RAM • On-chip 128 KB BootROM (not user visible) • Two AXI 3.0, 64-bit slave interfaces • Low latency path for CPU/ACP reads to OCM (CPU at 667 MHz – minimum 23 cycles) • Round-robin pre-arbitration between read and write AXI channels on OCM-interconnect port (non-CPU port) • Fixed priority arbitration between the CPU/ACP (via SCU) and OCM-interconnect AXI ports • Supports full AXI 64-bit bandwidth of simultaneous read and write commands (with optimal alignment restrictions) on the OCM interconnect port • Random access supported to RAM from AXI masters Zynq‐7000 EPP Technical Reference Manual www.xilinx.com 566 UG585 (v1.2) August 8, 2012 IRQ
• TrustZone support for on-chip RAM with 4 KB page granularity • Flexible address mapping capability • RAM byte-wise parity generation, checking, and interrupt support • Support for the following non-AXI features on the CPU (SCU) port: ° ° ° ° Zero line fill Pre-fetch hint Early BRESP Speculative line pre-fetch 29.1.3 System Viewpoint A system viewpoint of the OCM is illustrated in Figure 29-2. X-Ref Target - Figure 29-2 CPUs Snoop Control Unit AXI_ACP S0 S1 M0 M1 DDR AXI_HP S0 S1 S0 S1 On-chip RAM 256 kB Figure 29‐2: OCM System Viewpoint Chapter 29: On‐Chip Memory (OCM) OCM Interconnect UG585_c29_02_022212 Zynq‐7000 EPP Technical Reference Manual www.xilinx.com 567 UG585 (v1.2) August 8, 2012 M All other Masters Via Central Interconnect
Page 1 and 2:
Zynq-7000 EPP Technical Reference M
Page 3 and 4:
Date Version Revision 06/25/12 1.1
Page 5 and 6:
Chapter 3: Application Processing U
Page 7 and 8:
6.2.4 Reset Requirements . . . . .
Page 9 and 10:
10.2.2 Block Diagram . . . . . . .
Page 11 and 12:
13.2.9 FIFO Overrun and Underrun Co
Page 13 and 14:
16.1.2 Features . . . . . . . . . .
Page 15 and 16:
Chapter 20: I2C Controller 20.1 Int
Page 17 and 18:
25.8 GPIO and I2C Clocks . . . . .
Page 19 and 20:
Chapter 31: PCI Express 31.1 Introd
Page 21 and 22:
Introduction 1.1 Overview Chapter 1
Page 23 and 24:
The Zynq-7000 system is composed of
Page 25 and 26:
TrustZone Capabilities Chapter 1: I
Page 27 and 28:
DDR Controller Core and Transaction
Page 29 and 30:
• IEEE 802.3-2008 and IEEE 1588 r
Page 31 and 32:
UART Controllers (Two) Chapter 1: I
Page 33 and 34:
° ° Chapter 1: Introduction High-
Page 35 and 36:
° ° Two, 32-bit slave interfaces
Page 37 and 38:
XADC VCCADC, GNDADC N/A Analog powe
Page 39 and 40:
X-Ref Target - Figure 2-2 AHB Maste
Page 41 and 42:
X-Ref Target - Figure 2-3 PS Centra
Page 43 and 44:
• Width of NAND Flash limited to
Page 45 and 46:
Chapter 2: Signals, Interfaces, and
Page 47 and 48:
Table 2‐7: PL‐PS Signal Groups
Page 49 and 50:
2.6.5 DMA Req/Ack Signals Chapter 2
Page 51 and 52:
Application Processing Unit 3.1 Int
Page 53 and 54:
3.1.2 System‐level View Chapter 3
Page 55 and 56:
3.2 Cortex A9 Processors 3.2.1 Summ
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Memory Access Sequence When the pro
Page 63 and 64:
A TLB entry matches when these cond
Page 65 and 66:
• Large, shared register file, ad
Page 67 and 68:
Page 69 and 70:
Table 3‐1: Cache Controller Behav
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Full Line of Zero Write Chapter 3:
Page 77 and 78:
Page 79 and 80:
Table 3‐3: ACP Read and Write Beh
Page 81 and 82:
3.6 Support for TrustZone Within th
Page 83 and 84:
Page 85 and 86:
These are a few notes about the Tru
Page 87 and 88:
Page 89 and 90:
Notes: PL AXI Interface Note Chapte
Page 91 and 92:
Table 4‐3: SLCR Register Map (Con
Page 93 and 94:
4.7 Miscellaneous PS Registers The
Page 95 and 96:
Interconnect Masters The interconne
Page 97 and 98:
L2 Cache Controller Chapter 5: Inte
Page 99 and 100:
X-Ref Target - Figure 5-2 Chapter 5
Page 101 and 102:
Table 5‐3: Slave Visible AXI ID V
Page 103 and 104:
Chapter 5: Interconnect (through L2
Page 105 and 106:
5.3.3 Functional Description Chapte
Page 107 and 108:
Table 5‐6: Additional per-port HP
Page 109 and 110:
Chapter 5: Interconnect For the 32-
Page 111 and 112:
5.3.9 Performance Optimization Summ
Page 113 and 114:
5.5 AXI_GP Interfaces 5.5.1 Feature
Page 115 and 116:
Table 5‐8: AXI Signals Summary (C
Page 117 and 118:
Table 5‐8: AXI Signals Summary (C
Page 119 and 120:
Chapter 6: Boot and Configuration
Page 121 and 122:
Table 6‐2: Boot_Mode Strapping MI
Page 123 and 124:
Chapter 6: Boot and Configuration J
Page 125 and 126:
6.3.2 BootROM Header Chapter 6: Boo
Page 127 and 128:
Start of Execution — Byte Offset
Page 129 and 130:
Chapter 6: Boot and Configuration G
Page 131 and 132:
Table 6‐6: NAND MIO Pins Signal N
Page 133 and 134:
Chapter 6: Boot and Configuration 1
Page 135 and 136:
Chapter 6: Boot and Configuration T
Page 137 and 138:
6.3.6 Debug Status Chapter 6: Boot
Page 139 and 140:
Table 6‐10: BootROM Modified Regi
Page 141 and 142:
Page 143 and 144:
X-Ref Target - Figure 6-6 pcap_2xcl
Page 145 and 146:
6.4.4 Device Configuration Flow PS
Page 147 and 148:
Chapter 6: Boot and Configuration b
Page 149 and 150:
The configuration flow is: 1. Devic
Page 151 and 152:
Page 153 and 154:
7.1.1 Private, Shared and Software
Page 155 and 156:
7.2 Functional Description 7.2.1 So
Page 157 and 158:
Table 7‐3: PS and PL Shared Perip
Page 159 and 160:
7.3.1 Write Protection Lock Down Ch
Page 161 and 162:
Timers 8.1 Introduction Chapter 8 E
Page 163 and 164:
Chapter 8: Timers Although peripher
Page 165 and 166:
8.4.2 Block Diagram A block diagram
Page 167 and 168:
8.5 Triple Timer Counters (TTC) Cha
Page 169 and 170:
Chapter 8: Timers Overflow mode: Th
Page 171 and 172:
Chapter 8: Timers 2. Set overflow h
Page 173 and 174:
DMA Controller 9.1 Introduction Cha
Page 175 and 176:
Chapter 9: DMA Controller ° Signal
Page 177 and 178:
9.1.3 Block Diagram X-Ref Target -
Page 179 and 180:
Reset Initialization Interface Chap
Page 181 and 182:
X-Ref Target - Figure 9-4 CPU_3x2x
Page 183 and 184:
9.2.3 Memory to/from PL Peripheral
Page 185 and 186:
Chapter 9: DMA Controller specifies
Page 187 and 188:
Chapter 9: DMA Controller The DMALD
Page 189 and 190:
Table 9‐2: Event/Interrupt Resour
Page 191 and 192:
Table 9‐4: Abort Handling Thread
Page 193 and 194:
Table 9‐8: Security Usage Summary
Page 195 and 196:
9.3.3 Reset Initialization Interfac
Page 197 and 198:
Chapter 9: DMA Controller 9.5 Instr
Page 199 and 200:
9.6.2 Memory to Memory Chapter 9: D
Page 201 and 202:
Table 9‐15: Unaligned Transfers (
Page 203 and 204:
# Only loopback if servicing a burs
Page 205 and 206:
Chapter 9: DMA Controller For examp
Page 207 and 208:
When a discontinuity in the source
Page 209 and 210:
DDR Memory Controller 10.1 Introduc
Page 211 and 212:
X-Ref Target - Figure 10-1 Chapter
Page 213 and 214:
Table 10‐1: Connectivity Limitati
Page 215 and 216:
• Deep read and write command acc
Page 217 and 218:
X-Ref Target - Figure 10-4 DDR Inte
Page 219 and 220:
X-Ref Target - Figure 10-5 10.4.1 P
Page 221 and 222:
X-Ref Target - Figure 10-6 Aging Co
Page 223 and 224:
X-Ref Target - Figure 10-8 DDR Inte
Page 225 and 226:
Chapter 10: DDR Memory Controller I
Page 227 and 228:
10.5.1 Loopback Chapter 10: DDR Mem
Page 229 and 230:
Table 10‐7: Calibration Field Nam
Page 231 and 232:
10.6.4 DDR Controller Register Prog
Page 233 and 234:
Chapter 10: DDR Memory Controller a
Page 235 and 236:
Automatic Training The standard tra
Page 237 and 238:
10.7 Register Overviews Chapter 10:
Page 239 and 240:
Table 10‐11: DDRI Registers Overv
Page 241 and 242:
Operating Modes Chapter 10: DDR Mem
Page 243 and 244:
10.9.4 Self Refresh Chapter 10: DDR
Page 245 and 246:
11.1.1 Features Chapter 11: Static
Page 247 and 248:
11.1.3 Notices 7z010 CLG225 Device
Page 249 and 250:
11.3 I/O Signals Chapter 11: Static
Page 251 and 252:
X-Ref Target - Figure 11-5 SMC Cont
Page 253 and 254:
Quad‐SPI Flash Controller 12.1 In
Page 255 and 256:
Chapter 12: Quad‐SPI Flash Contro
Page 257 and 258:
Page 259 and 260:
Table 12‐2: Ignored AXI Read Addr
Page 261 and 262:
12.3 Programming Guide Example: Sta
Page 263 and 264:
Page 265 and 266:
Page 267 and 268:
Example: Read Data Sequence In this
Page 269 and 270:
CPU_1x Clock Chapter 12: Quad‐SPI
Page 271 and 272:
X-Ref Target - Figure 12-5 Dual SS,
Page 273 and 274:
12.5.2 MIO Programming Chapter 12:
Page 275 and 276:
a. Route Quad-SPI feedback clock ou
Page 277 and 278:
X-Ref Target - Figure 13-1 AHB Inte
Page 279 and 280:
• CRC generator and checker (CRC7
Page 281 and 282:
Read Chapter 13: SD/SDIO Peripheral
Page 283 and 284:
The sequence for data transfers wit
Page 285 and 286:
Chapter 13: SD/SDIO Peripheral Cont
Page 287 and 288:
13.3.4 Using ADMA X-Ref Target - Fi
Page 289 and 290:
X-Ref Target - Figure 13-6 Synchron
Page 291 and 292:
13.3.8 Bus Voltage Translation Chap
Page 293 and 294:
Chapter 13: SD/SDIO Peripheral Cont
Page 295 and 296:
14.2 Block Diagram X-Ref Target - F
Page 297 and 298:
MIO bank control (for Bank0 and Ban
Page 299 and 300:
Chapter 14: General Purpose I/O (GP
Page 301 and 302:
Chapter 15: USB Host, Device, and O
Page 303 and 304:
Page 305 and 306:
15.3.1 Block Diagram Chapter 15: US
Page 307 and 308:
15.5 Host Data Structure X-Ref Targ
Page 309 and 310:
15.6.2 DMA Engine X-Ref Target - Fi
Page 311 and 312:
15.6.5 Port Controller X-Ref Target
Page 313 and 314:
Page 315 and 316:
The change is a fundamental one in
Page 317 and 318:
Asynchronous Transaction Scheduling
Page 319 and 320:
Discovery Port Reset Chapter 15: US
Page 321 and 322:
15.8.2 Port State and Control Chapt
Page 323 and 324:
Page 325 and 326:
Data Toggle Chapter 15: USB Host, D
Page 327 and 328:
Table 15‐6: Variable Length Trans
Page 329 and 330:
Control Endpoint Operation Model Se
Page 331 and 332:
Table 15‐9: Control Endpoint Bus
Page 333 and 334:
Page 335 and 336:
Page 337 and 338:
Active = 0 Halted = 0 Transaction E
Page 339 and 340:
Low‐Frequency Interrupts Chapter
Page 341 and 342:
Page 343 and 344:
X-Ref Target - Figure 15-16 Operati
Page 345 and 346:
Page 347 and 348:
Table 15‐19: iTD Transaction Stat
Page 349 and 350:
Table 15‐22: iTD Buffer Pointer P
Page 351 and 352:
15.10.9 siTD Endpoint Capabilities/
Page 353 and 354:
Page 355 and 356:
15.10.12 siTD Back Link Pointer Cha
Page 357 and 358:
15.10.15 Alternate Next qTD Pointer
Page 359 and 360:
Page 361 and 362:
7:0 (cont’d) 15.10.17 qTD Buffer
Page 363 and 364:
15.10.19 Queue Head Horizontal Link
Page 365 and 366:
Table 15‐36: Endpoint Capabilitie
Page 367 and 368:
Table 15‐38: Host‐Controller Ru
Page 369 and 370:
15.10.24 FSTN Back Path Link Pointe
Page 371 and 372:
X-Ref Target - Figure 15-24 Endpoin
Page 373 and 374:
Page 375 and 376:
Page 377 and 378:
Gigabit Ethernet Controller 16.1 In
Page 379 and 380:
Chapter 16: Gigabit Ethernet Contro
Page 381 and 382:
Page 383 and 384:
Page 385 and 386:
Page 387 and 388:
Page 389 and 390:
Table 16‐2: Rx Buffer Descriptor
Page 391 and 392:
Page 393 and 394:
Table 16‐3: Tx Buffer Descriptor
Page 395 and 396:
X-Ref Target - Figure 16-3 Gigabit
Page 397 and 398:
Page 399 and 400:
Page 401 and 402:
Counter Value to the PL Chapter 16:
Page 403 and 404:
Page 405 and 406:
Page 407 and 408:
X-Ref Target - Figure 16-4 To creat
Page 409 and 410:
Page 411 and 412:
Table 16‐6: Ethernet Control Regi
Page 413 and 414:
16.5 Signals and I/O Connections 16
Page 415 and 416:
Table 16‐8: Ethernet RGMII Interf
Page 417 and 418:
SPI Controller 17.1 Introduction Ch
Page 419 and 420:
17.2 Functional Description 17.2.1
Page 421 and 422:
17.2.4 Slave Mode Chapter 17: SPI C
Page 423 and 424:
Table 17‐1: SPI MIO Pins and EMIO
Page 425 and 426:
18.1.2 System Viewpoint The system
Page 427 and 428:
18.2 Functional Description Chapter
Page 429 and 430:
Normal Mode Chapter 18: CAN Control
Page 431 and 432:
Table 18‐3: CAN Message Word Regi
Page 433 and 434:
Chapter 18: CAN Controller When arb
Page 435 and 436:
X-Ref Target - Figure 18-4 Table 18
Page 437 and 438:
Chapter 18: CAN Controller If any o
Page 439 and 440:
d. Zero-out extended frame bits, [A
Page 441 and 442:
tBIT_RATE = tSYNC_SEGMENT + tTIME_S
Page 443 and 444:
Chapter 18: CAN Controller 3. Wait
Page 445 and 446:
5. Determine if more messages are i
Page 447 and 448:
Chapter 18: CAN Controller 1. Confi
Page 449 and 450:
18.5.2 MIO‐EMIO Signals Chapter 1
Page 451 and 452:
° 1, 1.5, or 2 stop bits Chapter 1
Page 453 and 454:
19.2 Functional Description 19.2.1
Page 455 and 456:
19.2.3 Transmitter Data Stream Chap
Page 457 and 458:
19.2.6 Mode Switch X-Ref Target - F
Page 459 and 460:
4. Configure Baud Rate Generator (s
Page 461 and 462:
Chapter 19: UART Controller 4. Repe
Page 463 and 464:
Non‐FIFO Interrupts Chapter 19: U
Page 465 and 466:
19.4 System Functions 19.4.1 Clocks
Page 467 and 468:
Table 19‐4: UART MIO Pins and EMI
Page 469 and 470:
° Supports TO interrupt flag to av
Page 471 and 472:
Chapter 20: I2C Controller data is
Page 473 and 474:
Chapter 20: I2C Controller At the s
Page 475 and 476:
20.3 Register Overview An overview
Page 477 and 478:
Chapter 21: Programmable Logic Desc
Page 479 and 480:
Page 481 and 482:
Error Detection and Correction Chap
Page 483 and 484:
Page 485 and 486:
Page 487 and 488:
21.3 PS‐PL Interfaces Chapter 21:
Page 489 and 490:
Power Chapter 22: Programmable Logi
Page 491 and 492:
Chapter 22: Programmable Logic Desi
Page 493 and 494:
Page 495 and 496:
Page 497 and 498:
X-Ref Target - Figure 22-1 MIO Pins
Page 499 and 500:
X-Ref Target - Figure 22-3 MIO Pins
Page 501 and 502:
Page 503 and 504:
Page 505 and 506:
23.1.2 Block Diagram A block diagra
Page 507 and 508:
Chapter 23: Programmable Logic (PL)
Page 509 and 510:
X-Ref Target - Figure 23-5 PL Activ
Page 511 and 512:
Table 23‐5: Cycle Count Packet Fo
Page 513 and 514:
23.4 Register Overview Table 23‐1
Page 515 and 516:
24.2 Voltage Domains Figure 24-1 sh
Page 517 and 518:
Clocks 25.1 Introduction Chapter 25
Page 519 and 520:
25.1.4 System Viewpoint X-Ref Targe
Page 521 and 522: 25.3 CPU Clock Domains X-Ref Target
Page 523 and 524: Table 25‐2: PS Peripheral Clock C
Page 525 and 526: X-Ref Target - Figure 25-4 These fe
Page 527 and 528: 25.7 I/O Peripheral (IOP) Clocks I/
Page 529 and 530: Chapter 25: Clocks the RGMII interf
Page 531 and 532: X-Ref Target - Figure 25-10 IO PLL
Page 533 and 534: 25.12 Programming Model 25.12.1 Bra
Page 535 and 536: Table 25‐5: PLL Frequency Control
Page 537 and 538: Chapter 25: Clocks Zynq‐7000 EPP
Page 539 and 540: X-Ref Target - Figure 26-1 PS_POR_B
Page 541 and 542: X-Ref Target - Figure 26-3 System R
Page 543 and 544: Chapter 26: Reset System The PS doe
Page 545 and 546: Chapter 26: Reset System The first
Page 547 and 548: X-Ref Target - Figure 27-1 Chapter
Page 549 and 550: 27.2 Functional Description Chapter
Page 551 and 552: Chapter 27: JTAG and DAP Subsystem
Page 553 and 554: Chapter 27: JTAG and DAP Subsystem
Page 555 and 556: 27.6 Trace Port Interface Unit (TPI
Page 557 and 558: System Test and Debug 28.1 Introduc
Page 559 and 560: • Trace source: PTM, FTM, ITM •
Page 561 and 562: Table 28‐1: CTI Trigger Inputs an
Page 563 and 564: 28.2.6 Embedded Trace Buffer (ETB)
Page 565 and 566: 28.4 Register Overview 28.4.1 Memor
Page 567 and 568: Table 28‐6: CoreSight Component R
Page 569 and 570: 28.5 Programming Model 28.5.1 Authe
Page 571: On‐Chip Memory (OCM) 29.1 Introdu
Page 575 and 576: X-Ref Target - Figure 29-3 Arbitrat
Page 577 and 578: OCM Relocation Chapter 29: On‐Chi
Page 579 and 580: 29.2.5 Interrupts Chapter 29: On‐
Page 581 and 582: Chapter 29: On‐Chip Memory (OCM)
Page 583 and 584: 30.1.1 Block Diagram Figure 30-1 sh
Page 585 and 586: Chapter 30: Analog‐to‐Digital C
Page 587 and 588: 30.5 Programming Model Chapter 30:
Page 589 and 590: 31.2 Block Diagram X-Ref Target - F
Page 591 and 592: Device Secure Boot 32.1 Introductio
Page 593 and 594: 32.2 Functional Description 32.2.1
Page 595 and 596: X-Ref Target - Figure 32-3 BootROM
Page 597 and 598: 32.2.8 Key Management Chapter 32: D
Page 599 and 600: Chapter 32: Device Secure Boot resu
Page 601 and 602: A.2 Solution Centers Appendix A: Ad
Page 603 and 604: ChipScope Pro Software and Cores Us
Page 605 and 606: Register Details B.1 Overview Appen
Page 607 and 608: B.3 Module Summary Module Name Modu
Page 609 and 610: Module Name Module Type Base Addres
Page 611 and 612: Register Name Address Width Type Re
Page 613 and 614: Register (AFI) AFI_RDCHAN_ISSUINGCA
Page 615 and 616: Absolute Address afi0: 0xF8008010 a
Page 617 and 618: Field Name Bits Type Reset Value De
Page 619 and 620: Register (AFI) AFI_WRDATAFIFO_LEVEL
Page 621 and 622: B.5 CAN Controller (can) Module Nam
Page 623 and 624:
Register SRR Details Appendix B: Re
Page 625 and 626:
Please refer to the CAN chapter for
Page 627 and 628:
Field Name Bits Type Reset Value De
Page 629 and 630:
Page 631 and 632:
Page 633 and 634:
Page 635 and 636:
ETXFWMEMP (IXR_TXFWMEMP) ERXFWMFLL
Page 637 and 638:
Page 639 and 640:
CTXFWMEMP (IXR_TXFWMEMP) CRXFWMFLL
Page 641 and 642:
Description Watermark Interrupt Reg
Page 643 and 644:
Register (can) TXFIFO_DLC Name TXFI
Page 645 and 646:
Page 647 and 648:
Register TXHPB_DLC Details Field Na
Page 649 and 650:
IDH (IDR_ID1) SRRRTR (IDR_SRR) IDE
Page 651 and 652:
Register RXFIFO_DATA1 Details Field
Page 653 and 654:
Page 655 and 656:
Page 657 and 658:
Register AFMR2 Details Field Name B
Page 659 and 660:
Page 661 and 662:
Page 663 and 664:
Register AFMR4 Details Field Name B
Page 665 and 666:
Page 667 and 668:
Register Name Address Width Type Re
Page 669 and 670:
Page 671 and 672:
Page 673 and 674:
Page 675 and 676:
Register (ddrc) DRAM_param_reg0 Nam
Page 677 and 678:
Reset Value 0x83015904 Description
Page 679 and 680:
Page 681 and 682:
Page 683 and 684:
Description DRAM EMR, MR access Reg
Page 685 and 686:
Page 687 and 688:
Page 689 and 690:
Page 691 and 692:
Page 693 and 694:
Register phy_cmd_timeout_rddata_cpt
Page 695 and 696:
Register (ddrc) DLL_calib Name DLL_
Page 697 and 698:
Page 699 and 700:
Name ctrl_reg4 Register (ddrc) ctrl
Page 701 and 702:
Name ctrl_reg6 Register (ddrc) ctrl
Page 703 and 704:
Register (ddrc) CHE_T_ZQ_Short_Inte
Page 705 and 706:
Page 707 and 708:
Width 2 bits Access Type rw Reset V
Page 709 and 710:
Page 711 and 712:
Register CHE_UNCORR_ECC_LOG_REG_OFF
Page 713 and 714:
Register CHE_UNCORR_ECC_DATA_71_64_
Page 715 and 716:
Register CHE_ECC_CORR_BIT_MASK_31_0
Page 717 and 718:
Name Address PHY_Config0 0xf8006118
Page 719 and 720:
Name Address phy_rd_dqs_cfg0 0xf800
Page 721 and 722:
Register phy_we_cfg0 to phy_we_cfg3
Page 723 and 724:
Page 725 and 726:
Page 727 and 728:
Register reg6c_6d2 to reg6c_6d3 Det
Page 729 and 730:
Register dll_lock_sts Details Field
Page 731 and 732:
Name axi_id Register (ddrc) axi_id
Page 733 and 734:
Register (ddrc) axi_priority_rd_por
Page 735 and 736:
Register excl_access_cfg0 to excl_a
Page 737 and 738:
Register lpddr_ctrl2 Details Field
Page 739 and 740:
Register (ddrc) phy_gate_lvl_fsm Na
Page 741 and 742:
Page 743 and 744:
Register (cti) CTIINTACK Name CTIIN
Page 745 and 746:
Absolute Address debug_cpu_cti0: 0x
Page 747 and 748:
Register (cti) CTIINEN2 Name CTIINE
Page 749 and 750:
Register (cti) CTIINEN5 Name CTIINE
Page 751 and 752:
Register (cti) CTIOUTEN0 Name CTIOU
Page 753 and 754:
Page 755 and 756:
Page 757 and 758:
Page 759 and 760:
Page 761 and 762:
Page 763 and 764:
Description ITTRIGIN Register Regis
Page 765 and 766:
Width 32 bits Access Type wo Reset
Page 767 and 768:
Register (cti) DEVID Name DEVID Rel
Page 769 and 770:
Relative Address 0x00000FD8 Absolut
Page 771 and 772:
Page 773 and 774:
Width 8 bits Access Type ro Reset V
Page 775 and 776:
Register (cortexa9_pmu) PMXEVCNTR0
Page 777 and 778:
Register (cortexa9_pmu) PMXEVCNTR5
Page 779 and 780:
Register (cortexa9_pmu) PMXEVTYPER3
Page 781 and 782:
Register (cortexa9_pmu) PMINTENSET
Page 783 and 784:
Register (cortexa9_pmu) PMUSERENR N
Page 785 and 786:
Page 787 and 788:
Page 789 and 790:
Page 791 and 792:
Register (ptm) ETMTSSCR Name ETMTSS
Page 793 and 794:
Register (ptm) ETMACVR2 Name ETMACV
Page 795 and 796:
Register (ptm) ETMACVR7 Name ETMACV
Page 797 and 798:
Register ETMACTR2 Details Field Nam
Page 799 and 800:
Page 801 and 802:
Page 803 and 804:
Page 805 and 806:
Width 18 bits Access Type mixed Res
Page 807 and 808:
Register (ptm) ETMCNTVR2 Name ETMCN
Page 809 and 810:
Register ETMSQ23EVR Details Field N
Page 811 and 812:
Register ETMSQ13EVR Details Field N
Page 813 and 814:
Access Type rw Reset Value 0x000000
Page 815 and 816:
Access Type ro Reset Value 0x00C019
Page 817 and 818:
Page 819 and 820:
Register ITMISCOUT Details Field Na
Page 821 and 822:
Register ITATBCTR2 Details Field Na
Page 823 and 824:
Register CTSR Details Field Name Bi
Page 825 and 826:
Register LSR Details Field Name Bit
Page 827 and 828:
Register DTIR Details Field Name Bi
Page 829 and 830:
Access Type ro Reset Value 0x000000
Page 831 and 832:
Register (ptm) COMPID1 Name COMPID1
Page 833 and 834:
B.10 Debug Access Port (dap) Module
Page 835 and 836:
Width 32 bits Access Type ro Reset
Page 837 and 838:
Page 839 and 840:
Reset Value 0x0000B003 Description
Page 841 and 842:
Page 843 and 844:
Register ROMENTRY15 Details Field N
Page 845 and 846:
Register PERIPHID0 Details Field Na
Page 847 and 848:
Description Component ID1 Register
Page 849 and 850:
Page 851 and 852:
Register RRD Details Field Name Bit
Page 853 and 854:
Register CTL Details Field Name Bit
Page 855 and 856:
Page 857 and 858:
Page 859 and 860:
Name CTSR Register (etb) CTSR Relat
Page 861 and 862:
Page 863 and 864:
Page 865 and 866:
Page 867 and 868:
Register COMPID2 Details Field Name
Page 869 and 870:
Page 871 and 872:
Page 873 and 874:
Register FTMP2FDBG3 Details Field N
Page 875 and 876:
Description AXI Cycle Count clock p
Page 877 and 878:
Register FTMITTRIGOUTACK Details Fi
Page 879 and 880:
Absolute Address 0xF880BEF0 Width 2
Page 881 and 882:
Register CLAIMTAGSET Details Field
Page 883 and 884:
Absolute Address 0xF880BFC8 Width 1
Page 885 and 886:
Relative Address 0x00000FDC Absolut
Page 887 and 888:
Register (ftm) FTMCOMPONID0 Name FT
Page 889 and 890:
B.13 CoreSight Trace Funnel (funnel
Page 891 and 892:
Page 893 and 894:
Register ITATBCTR2 Details Field Na
Page 895 and 896:
Register CTSR Details Field Name Bi
Page 897 and 898:
Page 899 and 900:
Page 901 and 902:
Page 903 and 904:
Register COMPID2 Details Field Name
Page 905 and 906:
Page 907 and 908:
Register StimPort00 Details Field N
Page 909 and 910:
Page 911 and 912:
Page 913 and 914:
Page 915 and 916:
Page 917 and 918:
Page 919 and 920:
Page 921 and 922:
Page 923 and 924:
Page 925 and 926:
Page 927 and 928:
Page 929 and 930:
Page 931 and 932:
Page 933 and 934:
Page 935 and 936:
Page 937 and 938:
Page 939 and 940:
Absolute Address 0xF8805E20 Width 3
Page 941 and 942:
Description Integration Test Trigge
Page 943 and 944:
Description Integration Mode Contro
Page 945 and 946:
Relative Address 0x00000FB4 Absolut
Page 947 and 948:
Relative Address 0x00000FD0 Absolut
Page 949 and 950:
Absolute Address 0xF8805FE4 Width 8
Page 951 and 952:
Relative Address 0x00000FF8 Absolut
Page 953 and 954:
Page 955 and 956:
Reset Value 0x0000011F Description
Page 957 and 958:
Register (tpiu) CurrentTest Name Cu
Page 959 and 960:
Page 961 and 962:
Register ITTRFLINACK Details Field
Page 963 and 964:
Relative Address 0x00000EF8 Absolut
Page 965 and 966:
Description Lock Access Register Re
Page 967 and 968:
Page 969 and 970:
Page 971 and 972:
Register (tpiu) COMPID0 Name COMPID
Page 973 and 974:
B.16 Device Configuration Interface
Page 975 and 976:
Page 977 and 978:
Page 979 and 980:
Page 981 and 982:
Register LOCK Details Appendix B: R
Page 983 and 984:
Page 985 and 986:
Page 987 and 988:
Page 989 and 990:
Page 991 and 992:
Register (devcfg) ROM_SHADOW Name R
Page 993 and 994:
Register MCTRL Details Field Name B
Page 995 and 996:
Register XADCIF_INT_STS Details Fie
Page 997 and 998:
Register XADCIF_CMDFIFO Details Fie
Page 999 and 1000:
B.17 DMA Controller (dmac) Module N
Page 1001 and 1002:
Page 1003 and 1004:
Page 1005 and 1006:
Register DSR Details Field Name Bit
Page 1007 and 1008:
Page 1009 and 1010:
Absolute Address dmac0_ns: 0xF80040
Page 1011 and 1012:
Page 1013 and 1014:
Page 1015 and 1016:
Register FTR1 Details Field Name Bi
Page 1017 and 1018:
Page 1019 and 1020:
Page 1021 and 1022:
Page 1023 and 1024:
Page 1025 and 1026:
Page 1027 and 1028:
Page 1029 and 1030:
Page 1031 and 1032:
Page 1033 and 1034:
Page 1035 and 1036:
Page 1037 and 1038:
Page 1039 and 1040:
Page 1041 and 1042:
Page 1043 and 1044:
Page 1045 and 1046:
Description Channel PC for DMA chan
Page 1047 and 1048:
Relative Address 0x00000124 Absolut
Page 1049 and 1050:
Page 1051 and 1052:
Page 1053 and 1054:
Page 1055 and 1056:
Description Channel PC for DMA chan
Page 1057 and 1058:
Page 1059 and 1060:
Page 1061 and 1062:
Register LC0_0 Details Field Name B
Page 1063 and 1064:
Reset Value dmac0_ns: 0x00000000 dm
Page 1065 and 1066:
Page 1067 and 1068:
Page 1069 and 1070:
Page 1071 and 1072:
Page 1073 and 1074:
Page 1075 and 1076:
Page 1077 and 1078:
Page 1079 and 1080:
Page 1081 and 1082:
Page 1083 and 1084:
Page 1085 and 1086:
Page 1087 and 1088:
Page 1089 and 1090:
Page 1091 and 1092:
Page 1093 and 1094:
Page 1095 and 1096:
Page 1097 and 1098:
Page 1099 and 1100:
Page 1101 and 1102:
Page 1103 and 1104:
Page 1105 and 1106:
Page 1107 and 1108:
Page 1109 and 1110:
Page 1111 and 1112:
Access Type mixed Reset Value 0x000
Page 1113 and 1114:
Page 1115 and 1116:
Page 1117 and 1118:
Register CR3 Details Register (dmac
Page 1119 and 1120:
Page 1121 and 1122:
Page 1123 and 1124:
Register pcell_id_0 Details Field N
Page 1125 and 1126:
B.18 Gigabit Ethernet Controller (G
Page 1127 and 1128:
Page 1129 and 1130:
Page 1131 and 1132:
Name net_cfg Register (GEM) net_cfg
Page 1133 and 1134:
len_err_frame_disc (LENGTHERRDSCRD)
Page 1135 and 1136:
Page 1137 and 1138:
Page 1139 and 1140:
Name tx_status Register (GEM) tx_st
Page 1141 and 1142:
Register rx_qbar Details Appendix B
Page 1143 and 1144:
Register (GEM) intr_status Name int
Page 1145 and 1146:
Page 1147 and 1148:
Page 1149 and 1150:
Page 1151 and 1152:
Page 1153 and 1154:
Appendix B: Register Details operat
Page 1155 and 1156:
Name hash_top Register (GEM) hash_t
Page 1157 and 1158:
Register (GEM) spec_addr2_top Name
Page 1159 and 1160:
Register (GEM) spec_addr4_top Name
Page 1161 and 1162:
Page 1163 and 1164:
Register ipg_stretch Details Field
Page 1165 and 1166:
Register (GEM) spec_addr1_mask_top
Page 1167 and 1168:
Register octets_tx_top Details Appe
Page 1169 and 1170:
Register multi_frames_tx Details Ap
Page 1171 and 1172:
Register (GEM) frames_128to255b_tx
Page 1173 and 1174:
Description Frame Tx, 1024 to 1518-
Page 1175 and 1176:
Register multi_collisn_frames Detai
Page 1177 and 1178:
Description Deferred Transmission F
Page 1179 and 1180:
Register (GEM) octets_rx_top Name o
Page 1181 and 1182:
Register (GEM) multi_frames_rx Name
Page 1183 and 1184:
Page 1185 and 1186:
Page 1187 and 1188:
Name jab_rx Register (GEM) jab_rx S
Page 1189 and 1190:
Software Name XEMACPS_RXSYMBCNT Rel
Page 1191 and 1192:
Absolute Address gem0: 0xE000B1A4 g
Page 1193 and 1194:
Register udp_csum_errors Details Fi
Page 1195 and 1196:
Register timer_ns Details Field Nam
Page 1197 and 1198:
Name ptp_tx_ns Register (GEM) ptp_t
Page 1199 and 1200:
Page 1201 and 1202:
Register ptp_peer_rx_ns Details Fie
Page 1203 and 1204:
Page 1205 and 1206:
B.19 General Purpose I/O (gpio) Mod
Page 1207 and 1208:
Page 1209 and 1210:
Page 1211 and 1212:
Page 1213 and 1214:
Page 1215 and 1216:
Register (gpio) DATA_2_RO Name DATA
Page 1217 and 1218:
Page 1219 and 1220:
Software Name INTSTS Relative Addre
Page 1221 and 1222:
Description Interrupt Any Edge Sens
Page 1223 and 1224:
Page 1225 and 1226:
Absolute Address 0xE000A264 Width 2
Page 1227 and 1228:
Page 1229 and 1230:
Absolute Address 0xE000A2A4 Width 3
Page 1231 and 1232:
Page 1233 and 1234:
Absolute Address 0xE000A2E4 Width 3
Page 1235 and 1236:
Absolute Address gpv_qos301_cpu: 0x
Page 1237 and 1238:
Name aw_p Register (qos301) aw_p Re
Page 1239 and 1240:
Page 1241 and 1242:
Register (nic301_addr_region_ctrl_r
Page 1243 and 1244:
Page 1245 and 1246:
Page 1247 and 1248:
Page 1249 and 1250:
Width 16 bits Access Type ro Reset
Page 1251 and 1252:
TO (IXR_TO) Field Name Bits Type Re
Page 1253 and 1254:
B.23 L2 Cache (L2Cpl310) Module Nam
Page 1255 and 1256:
Page 1257 and 1258:
Page 1259 and 1260:
Page 1261 and 1262:
Page 1263 and 1264:
Page 1265 and 1266:
Register reg1_tag_ram_control Detai
Page 1267 and 1268:
Page 1269 and 1270:
Page 1271 and 1272:
Register reg2_int_mask Details Regi
Page 1273 and 1274:
Register reg2_int_raw_status Detail
Page 1275 and 1276:
Page 1277 and 1278:
Page 1279 and 1280:
Register (L2Cpl310) reg9_d_lockdown
Page 1281 and 1282:
Register (L2Cpl310) reg9_d_lockdown
Page 1283 and 1284:
Register reg9_d_lockdown4 Details F
Page 1285 and 1286:
Page 1287 and 1288:
Register reg9_unlock_way Details Fi
Page 1289 and 1290:
Page 1291 and 1292:
Register (L2Cpl310) reg15_power_ctr
Page 1293 and 1294:
Page 1295 and 1296:
Page 1297 and 1298:
Page 1299 and 1300:
Page 1301 and 1302:
Description SCU Invalidate All Regi
Page 1303 and 1304:
Page 1305 and 1306:
Register ICCICR Details Field Name
Page 1307 and 1308:
Register ICCIAR Details Field Name
Page 1309 and 1310:
Absolute Address 0xF8F0011C Width 3
Page 1311 and 1312:
Register (mpcore) Global_Timer_Cont
Page 1313 and 1314:
Absolute Address 0xF8F00210 Width 3
Page 1315 and 1316:
Register (mpcore) Private_Timer_Cou
Page 1317 and 1318:
Page 1319 and 1320:
Register Watchdog_Counter_Register
Page 1321 and 1322:
Register (mpcore) Watchdog_Interrup
Page 1323 and 1324:
Register Watchdog_Disable_Register
Page 1325 and 1326:
Register ICDICTR Details Field Name
Page 1327 and 1328:
Register ICDISR0 to ICDISR2 Details
Page 1329 and 1330:
Reset Value 0x0000FFFF Description
Page 1331 and 1332:
Register ICDISPR0 to ICDISPR2 Detai
Page 1333 and 1334:
Appendix B: Register Details Note:
Page 1335 and 1336:
Name Address ICDIPTR22 0xf8f01858 I
Page 1337 and 1338:
Description Interrupt Configuration
Page 1339 and 1340:
Register ppi_status Details Field N
Page 1341 and 1342:
Register ICDSGIR Details Field Name
Page 1343 and 1344:
Page 1345 and 1346:
Register ICPIDR3 Details Field Name
Page 1347 and 1348:
B.25 On‐Chip Memory (ocm) Module
Page 1349 and 1350:
Page 1351 and 1352:
B.26 Quad‐SPI Flash Controller (q
Page 1353 and 1354:
leg_flsh (IFMODE) Register Config_r
Page 1355 and 1356:
Register Intr_status_REG Details Fi
Page 1357 and 1358:
Register Intrpt_dis_REG Details Fie
Page 1359 and 1360:
Register En_REG Details Field Name
Page 1361 and 1362:
Page 1363 and 1364:
Register LPBK_DLY_ADJ Details Appen
Page 1365 and 1366:
Absolute Address 0xE000D0A0 Width 3
Page 1367 and 1368:
Page 1369 and 1370:
B.27 SD Controller (sdio) Module Na
Page 1371 and 1372:
Page 1373 and 1374:
Register Block_Size_Block_Count Det
Page 1375 and 1376:
Register (sdio) Transfer_Mode_Comma
Page 1377 and 1378:
Page 1379 and 1380:
Register Present_State Details Fiel
Page 1381 and 1382:
Page 1383 and 1384:
Description Host control register P
Page 1385 and 1386:
Page 1387 and 1388:
Absolute Address sd0: 0xE010002C sd
Page 1389 and 1390:
Page 1391 and 1392:
Page 1393 and 1394:
Page 1395 and 1396:
Page 1397 and 1398:
Page 1399 and 1400:
Page 1401 and 1402:
Register Capabilities Details Field
Page 1403 and 1404:
Page 1405 and 1406:
Page 1407 and 1408:
Register ADMA_system_address Detail
Page 1409 and 1410:
Register SPI_interrupt_support Deta
Page 1411 and 1412:
B.28 System Level Control Registers
Page 1413 and 1414:
Page 1415 and 1416:
Page 1417 and 1418:
Register SLCR_LOCK Details Field Na
Page 1419 and 1420:
Page 1421 and 1422:
Page 1423 and 1424:
Register (slcr) DDR_PLL_CFG Name DD
Page 1425 and 1426:
Page 1427 and 1428:
Page 1429 and 1430:
Description USB 1 ULPI Clock Contro
Page 1431 and 1432:
Page 1433 and 1434:
Page 1435 and 1436:
Register SPI_CLK_CTRL Details Field
Page 1437 and 1438:
Page 1439 and 1440:
Register TOPSW_CLK_CTRL Details Fie
Page 1441 and 1442:
Register FPGA2_CLK_CTRL Details Fie
Page 1443 and 1444:
Register PSS_RST_CTRL Details Field
Page 1445 and 1446:
Register USB_RST_CTRL Details Field
Page 1447 and 1448:
Register SDIO_RST_CTRL Details Fiel
Page 1449 and 1450:
Register CAN_RST_CTRL Details Field
Page 1451 and 1452:
Page 1453 and 1454:
Page 1455 and 1456:
Page 1457 and 1458:
Width 32 bits Access Type rw Reset
Page 1459 and 1460:
Page 1461 and 1462:
Page 1463 and 1464:
Register DDR_CAL_START Details Fiel
Page 1465 and 1466:
Register (slcr) DDR_URGENT_SEL Name
Page 1467 and 1468:
Page 1469 and 1470:
Page 1471 and 1472:
Page 1473 and 1474:
Page 1475 and 1476:
Page 1477 and 1478:
Page 1479 and 1480:
Page 1481 and 1482:
Page 1483 and 1484:
Register MIO_PIN_14 Details Field N
Page 1485 and 1486:
Page 1487 and 1488:
Page 1489 and 1490:
Page 1491 and 1492:
Page 1493 and 1494:
Page 1495 and 1496:
Page 1497 and 1498:
Page 1499 and 1500:
Page 1501 and 1502:
Page 1503 and 1504:
Page 1505 and 1506:
Page 1507 and 1508:
Page 1509 and 1510:
Page 1511 and 1512:
Relative Address 0x000007A8 Absolut
Page 1513 and 1514:
Register (slcr) MIO_PIN_44 Name MIO
Page 1515 and 1516:
Page 1517 and 1518:
Page 1519 and 1520:
Page 1521 and 1522:
Page 1523 and 1524:
Register (slcr) MIO_FMIO_GEM_SEL Na
Page 1525 and 1526:
Page 1527 and 1528:
Register (slcr) SD0_WP_CD_SEL Name
Page 1529 and 1530:
Absolute Address 0xF8000910 Width 3
Page 1531 and 1532:
Register (slcr) GPIOB_CFG_CMOS25 Na
Page 1533 and 1534:
Page 1535 and 1536:
Page 1537 and 1538:
Page 1539 and 1540:
Page 1541 and 1542:
Page 1543 and 1544:
Register (slcr) DDRIOB_DRIVE_SLEW_D
Page 1545 and 1546:
Register DDRIOB_DDR_CTRL Details Fi
Page 1547 and 1548:
Register DDRIOB_DCI_STATUS Details
Page 1549 and 1550:
Page 1551 and 1552:
int_en0 (INT_EN0) state (STATE) Fie
Page 1553 and 1554:
Register (pl353) memc_cfg_clr Name
Page 1555 and 1556:
Set_t6 (SET_T6) Set_t5 (SET_T5) Set
Page 1557 and 1558:
Page 1559 and 1560:
Page 1561 and 1562:
eserved 2 ro 0x0 Reserved. Do not m
Page 1563 and 1564:
Reset Value 0x0024ABCC Description
Page 1565 and 1566:
Register user_config Details Regist
Page 1567 and 1568:
Page 1569 and 1570:
Page 1571 and 1572:
Register (pl353) ecc_addr0_1 Name e
Page 1573 and 1574:
Register ecc_value1_1 Details Field
Page 1575 and 1576:
Register ecc_value3_1 Details Field
Page 1577 and 1578:
Absolute Address spi0: 0xE0006000 s
Page 1579 and 1580:
Register Intr_status_reg0 Details F
Page 1581 and 1582:
Page 1583 and 1584:
Register (SPI) En_reg0 Name En_reg0
Page 1585 and 1586:
Page 1587 and 1588:
Page 1589 and 1590:
Page 1591 and 1592:
Page 1593 and 1594:
Page 1595 and 1596:
Register (ttc) Clock_Control_3 Name
Page 1597 and 1598:
Register Counter_Control_2 Details
Page 1599 and 1600:
Value (MASK) Register Counter_Value
Page 1601 and 1602:
Absolute Address ttc0: 0xF800102C t
Page 1603 and 1604:
Description Match value Match (MATC
Page 1605 and 1606:
Match (MATCH) Register Match_3_Coun
Page 1607 and 1608:
Register (ttc) Interrupt_Register_3
Page 1609 and 1610:
Register Interrupt_Enable_3 Details
Page 1611 and 1612:
Absolute Address ttc0: 0xF8001078 t
Page 1613 and 1614:
B.33 UART Controller (UART) Module
Page 1615 and 1616:
TXRES (TXRST) RXRES (RXRST) Field N
Page 1617 and 1618:
Page 1619 and 1620:
Register Intrpt_mask_reg0 Details F
Page 1621 and 1622:
Page 1623 and 1624:
Page 1625 and 1626:
Page 1627 and 1628:
Page 1629 and 1630:
B.34 USB Controller (usb) Module Na
Page 1631 and 1632:
Page 1633 and 1634:
Page 1635 and 1636:
Page 1637 and 1638:
Register (usb) HWTXBUF Name HWTXBUF
Page 1639 and 1640:
Page 1641 and 1642:
Page 1643 and 1644:
Register HCSPARAMS Details Field Na
Page 1645 and 1646:
Page 1647 and 1648:
Register USBCMD Details Field Name
Page 1649 and 1650:
Page 1651 and 1652:
HCH (IXR_HCH) Appendix B: Register
Page 1653 and 1654:
Absolute Address usb0: 0xE0002148 u
Page 1655 and 1656:
UEE (IXR_UE) UE (IXR_UI) Field Name
Page 1657 and 1658:
Register PERIODICLISTBASE_DEVICEADD
Page 1659 and 1660:
Register TTCTRL Details Field Name
Page 1661 and 1662:
Register TXFILLTUNING Details Field
Page 1663 and 1664:
Register IC_USB Details Field Name
Page 1665 and 1666:
Page 1667 and 1668:
Absolute Address usb0: 0xE0002178 u
Page 1669 and 1670:
Register (usb) PORTSC1 Name PORTSC1
Page 1671 and 1672:
Page 1673 and 1674:
Page 1675 and 1676:
Page 1677 and 1678:
Page 1679 and 1680:
Register USBMODE Details Field Name
Page 1681 and 1682:
Register ENDPTSETUPSTAT Details Fie
Page 1683 and 1684:
Register (usb) ENDPTFLUSH Name ENDP
Page 1685 and 1686:
Register ENDPTSTAT Details Field Na
Page 1687 and 1688:
Register (usb) ENDPTCTRL0 Name ENDP
Page 1689 and 1690:
Register ENDPTCTRL1 to ENDPTCTRL12
Page 1691:
Access Type Description w1crs w: 1/
show all

ug585-Zynq-7000-TRM

Create successful ePaper yourself

Delete template?

Save as template?