TigerSwitch 10/100/1000 Installation Guide - SMC

More documents

Recommendations

Info

ABOUT THE TIGERSWITCH 10/100/1000 Optional Redundant Power Unit 1-6 SMC provides an optional Redundant Power Unit (RPU), SMCRPU600W, that can supply power to the switch in the event of failure of the internal power supply. Power Supply Receptacles DC IN 12V 8.5A There are two power receptacles on the rear panel of the switch. The standard power receptacle is for the AC power cord. The receptacle labeled “RPU” is for the optional Redundant Power Unit. RPU Figure 1-3. Power Supply Receptacles 100-240V~, 50-60Hz 2A
Features and Benefits Connectivity FEATURES AND BENEFITS ◆ 24 dual-speed ports for easy Gigabit Ethernet integration and for protection of your investment in legacy LAN equipment. ◆ Auto-negotiation enables each RJ-45 port to automatically select the optimum communication mode (half or full duplex) if this feature is supported by the attached device; otherwise the port can be configured manually. ◆ Independent RJ-45 10/100/1000BASE-T ports with auto MDI/ MDI-X pinout selection. ◆ Unshielded (UTP) cable supported on all RJ-45 ports: Category 3, 4 or 5 for 10 Mbps connections, Category 5 or 5e for 100 Mbps connections, and Category 5 or better for 1000 Mbps connections. ◆ IEEE 802.3 Ethernet, 802.3u Fast Ethernet, 802.3z and 802.3ab Gigabit Ethernet compliance ensures compatibility with standards-based hubs, network cards and switches from any vendor. Expandability ◆ Supports 1000BASE-SX and 1000BASE-LX SFP transceivers. Performance ◆ Transparent bridging ◆ Switching table with a total of 16K MAC address entries ◆ Provides store-and-forward switching ◆ Supports wire-speed switching ◆ Supports flow control, using back pressure for half duplex and IEEE 802.3x for full duplex 1-7
Page 1: TigerSwitch 10/100/1000 Gigabit Eth
Page 4 and 5: Information furnished by SMC Networ
Page 6 and 7: ii WARRANTIES EXCLUSIVE: IF AN SMC
Page 8 and 9: COMPLIANCES iv voltage limits and t
Page 10 and 11: COMPLIANCES vi Safety Compliance Wa
Page 12 and 13: COMPLIANCES viii
Page 14 and 15: CONTENTS x Connecting to a Power So
Page 16 and 17: CONTENTS xii
Page 18 and 19: ABOUT THE TIGERSWITCH 10/100/1000 S
Page 20 and 21: ABOUT THE TIGERSWITCH 10/100/1000 S
Page 24 and 25: ABOUT THE TIGERSWITCH 10/100/1000 1
Page 26 and 27: NETWORK PLANNING Application Exampl
Page 28 and 29: NETWORK PLANNING Remote Connections
Page 30 and 31: NETWORK PLANNING Application Notes
Page 32 and 33: INSTALLING THE SWITCH Ethernet Cabl
Page 34 and 35: INSTALLING THE SWITCH Mounting 3-4
Page 36 and 37: INSTALLING THE SWITCH 3-6 3. If ins
Page 38 and 39: INSTALLING THE SWITCH Connecting to
Page 40 and 41: INSTALLING THE SWITCH 3-10
Page 42 and 43: MAKING NETWORK CONNECTIONS Connecti
Page 44 and 45: MAKING NETWORK CONNECTIONS Connecti
Page 46 and 47: MAKING NETWORK CONNECTIONS Cable La
Page 48 and 49: TROUBLESHOOTING Installation A-2 Ve
Page 50 and 51: CABLES Twisted-Pair Cable and Pin A
Page 52 and 53: CABLES 1000BASE-T MDI and MDI-X Por
Page 54 and 55: CABLES B-6
Page 56 and 57: SPECIFICATIONS C-2 Size 44.0 x 41.0
Page 58 and 59: SPECIFICATIONS C-4
Page 60 and 61: ORDERING INFORMATION D-2
Page 62 and 63: GLOSSARY Bandwidth The difference b
Page 64 and 65: GLOSSARY LAN Segment Separate LAN o
Page 66 and 67: GLOSSARY Glossary-6
Page 68 and 69: INDEX L port connections 4-1 power
Page 70: INDEX Index-4

TigerSwitch 10/100/1000 Installation Guide - SMC

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?