TigerSwitch 10/100/1000 Installation Guide - SMC

More documents

Recommendations

Info

TROUBLESHOOTING Installation A-2 Verify that all system components have been properly installed. If one or more components appear to be malfunctioning (such as the power cord or network cabling), test them in an alternate environment where you are sure that all the other components are functioning properly. In-Band Access You can access the management agent in the switch from anywhere within the attached network using Telnet, a Web browser, or other network management software tools. However, you must first configure the switch with a valid IP address, subnet mask, and default gateway. If you have trouble establishing a link to the management agent, check to see if you have a valid network connection. Then verify that you entered the correct IP address. Also, be sure the port through which you are connecting to the switch has not been disabled. If it has not been disabled, then check the network cabling that runs between your remote location and the switch. Caution: The management agent can accept up to four simultaneous Telnet sessions. If the maximum number of sessions already exists, an additional Telnet connection will not be able to log into the system.
Specifications APPENDIX B CABLES Cable Type Cable Types and Specifications Max. Length Connector 10BASE-T Cat. 3 or better 100-ohm UTP 100 m (328 ft) RJ-45 100BASE-TX Cat. 5 or better 100-ohm UTP 100 m (328 ft) RJ-45 1000BASE-T Cat. 5, 5e, 6 100-ohm UTP or 100 m (328 ft) STP RJ-45 1000BASE-SX 50/125 or 62.5/125 micron See the following LC core MMF table 1000BASE-LX 9/125 micron SMF 2 m - 5 km (7 ft - 3.2 miles) LC 1000BASE-ZX 9/125 micron SMF 70 - 100 km (43.5 - 62.1 miles) LC 1000BASE-SX Fiber Specifications Fiber Diameter Fiber Bandwidth Cable Length Range 62.5/125 micron 160 MHz/km 2-220 m (7-722 ft.) MMF 200 MHz/km 2-275 m (7-902 ft.) 50/125 micron 400 MHz/km 2-500 m (7-1641 ft.) MMF 500 MHz/km 2-550 m (7-1805 ft.) B-1
Page 1: TigerSwitch 10/100/1000 Gigabit Eth
Page 4 and 5: Information furnished by SMC Networ
Page 6 and 7: ii WARRANTIES EXCLUSIVE: IF AN SMC
Page 8 and 9: COMPLIANCES iv voltage limits and t
Page 10 and 11: COMPLIANCES vi Safety Compliance Wa
Page 12 and 13: COMPLIANCES viii
Page 14 and 15: CONTENTS x Connecting to a Power So
Page 16 and 17: CONTENTS xii
Page 18 and 19: ABOUT THE TIGERSWITCH 10/100/1000 S
Page 20 and 21: ABOUT THE TIGERSWITCH 10/100/1000 S
Page 22 and 23: ABOUT THE TIGERSWITCH 10/100/1000 O
Page 24 and 25: ABOUT THE TIGERSWITCH 10/100/1000 1
Page 26 and 27: NETWORK PLANNING Application Exampl
Page 28 and 29: NETWORK PLANNING Remote Connections
Page 30 and 31: NETWORK PLANNING Application Notes
Page 32 and 33: INSTALLING THE SWITCH Ethernet Cabl
Page 34 and 35: INSTALLING THE SWITCH Mounting 3-4
Page 36 and 37: INSTALLING THE SWITCH 3-6 3. If ins
Page 38 and 39: INSTALLING THE SWITCH Connecting to
Page 40 and 41: INSTALLING THE SWITCH 3-10
Page 42 and 43: MAKING NETWORK CONNECTIONS Connecti
Page 44 and 45: MAKING NETWORK CONNECTIONS Connecti
Page 46 and 47: MAKING NETWORK CONNECTIONS Cable La
Page 50 and 51: CABLES Twisted-Pair Cable and Pin A
Page 52 and 53: CABLES 1000BASE-T MDI and MDI-X Por
Page 54 and 55: CABLES B-6
Page 56 and 57: SPECIFICATIONS C-2 Size 44.0 x 41.0
Page 58 and 59: SPECIFICATIONS C-4
Page 60 and 61: ORDERING INFORMATION D-2
Page 62 and 63: GLOSSARY Bandwidth The difference b
Page 64 and 65: GLOSSARY LAN Segment Separate LAN o
Page 66 and 67: GLOSSARY Glossary-6
Page 68 and 69: INDEX L port connections 4-1 power
Page 70: INDEX Index-4

TigerSwitch 10/100/1000 Installation Guide - SMC

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?