TigerSwitch 10/100/1000 Installation Guide - SMC

More documents

Recommendations

Info

NETWORK PLANNING Application Notes 2-6 1. Full-duplex operation only applies to point-to-point access (such as when a switch is attached to a workstation, server or another switch). When the switch is connected to a hub, both devices must operate in half-duplex mode. 2. Avoid using flow control on a port connected to a hub unless it is actually required to solve a problem. Otherwise back pressure jamming signals may degrade overall performance for the segment attached to the hub. 3. As a general rule the length of fiber optic cable for a single switched link should not exceed 550 m (1805 ft) for multimode fiber or 5 km (16404 ft) for single-mode fiber. However, power budget constraints must also be considered when calculating the maximum cable length for your specific environment.
Selecting a Site CHAPTER 3 INSTALLING THE SWITCH TigerSwitch 10/100/1000 units can be mounted in a standard 19-inch equipment rack or on a flat surface. Be sure to follow the guidelines below when choosing a location. ◆ The site should: • be at the center of all the devices you want to link and near a power outlet. • be able to maintain its temperature within 0 to 50 °C (32 to 122 °F) and its humidity within 5% to 95%, non-condensing • provide adequate space (approximately two inches) on all sides for proper air flow • be accessible for installing, cabling and maintaining the devices • allow the status LEDs to be clearly visible ◆ Make sure twisted-pair cable is always routed away from power lines, fluorescent lighting fixtures and other sources of electrical interference, such as radios and transmitters. ◆ Make sure that a separate grounded power outlet that provides 100 to 240 VAC, 50 to 60 Hz, is within 2.44 m (8 feet) of each device and is powered from an independent circuit breaker. As with any equipment, using a filter or surge suppressor is recommended. 3-1
Page 1: TigerSwitch 10/100/1000 Gigabit Eth
Page 4 and 5: Information furnished by SMC Networ
Page 6 and 7: ii WARRANTIES EXCLUSIVE: IF AN SMC
Page 8 and 9: COMPLIANCES iv voltage limits and t
Page 10 and 11: COMPLIANCES vi Safety Compliance Wa
Page 12 and 13: COMPLIANCES viii
Page 14 and 15: CONTENTS x Connecting to a Power So
Page 16 and 17: CONTENTS xii
Page 18 and 19: ABOUT THE TIGERSWITCH 10/100/1000 S
Page 20 and 21: ABOUT THE TIGERSWITCH 10/100/1000 S
Page 22 and 23: ABOUT THE TIGERSWITCH 10/100/1000 O
Page 24 and 25: ABOUT THE TIGERSWITCH 10/100/1000 1
Page 26 and 27: NETWORK PLANNING Application Exampl
Page 28 and 29: NETWORK PLANNING Remote Connections
Page 32 and 33: INSTALLING THE SWITCH Ethernet Cabl
Page 34 and 35: INSTALLING THE SWITCH Mounting 3-4
Page 36 and 37: INSTALLING THE SWITCH 3-6 3. If ins
Page 38 and 39: INSTALLING THE SWITCH Connecting to
Page 40 and 41: INSTALLING THE SWITCH 3-10
Page 42 and 43: MAKING NETWORK CONNECTIONS Connecti
Page 44 and 45: MAKING NETWORK CONNECTIONS Connecti
Page 46 and 47: MAKING NETWORK CONNECTIONS Cable La
Page 48 and 49: TROUBLESHOOTING Installation A-2 Ve
Page 50 and 51: CABLES Twisted-Pair Cable and Pin A
Page 52 and 53: CABLES 1000BASE-T MDI and MDI-X Por
Page 54 and 55: CABLES B-6
Page 56 and 57: SPECIFICATIONS C-2 Size 44.0 x 41.0
Page 58 and 59: SPECIFICATIONS C-4
Page 60 and 61: ORDERING INFORMATION D-2
Page 62 and 63: GLOSSARY Bandwidth The difference b
Page 64 and 65: GLOSSARY LAN Segment Separate LAN o
Page 66 and 67: GLOSSARY Glossary-6
Page 68 and 69: INDEX L port connections 4-1 power
Page 70: INDEX Index-4

TigerSwitch 10/100/1000 Installation Guide - SMC

Create successful ePaper yourself

Delete template?

Save as template?