TigerSwitch 10/100/1000 Installation Guide - SMC

More documents

Recommendations

Info

CABLES Twisted-Pair Cable and Pin Assignments B-2 Caution: DO NOT plug a phone jack connector into any RJ-45 port. Use only twisted-pair cables with RJ-45 connectors that conform with FCC standards. For 10BASE-T/100BASE-TX connections, a twisted-pair cable must have two pairs of wires. Each wire pair is identified by two different colors. For example, one wire might be green and the other, green with white stripes. Also, an RJ-45 connector must be attached to both ends of the cable. Caution: Each wire pair must be attached to the RJ-45 connectors in a specific orientation. (See “Cabling Guidelines” on page 4-1 for an explanation.) Figure B-1 illustrates how the pins on the RJ-45 connector are numbered. Be sure to hold the connectors in the same orientation when attaching the wires to the pins. 10BASE-T/100BASE-TX Pin Assignments Figure B-1. RJ-45 Connector Pin Numbers Use unshielded twisted-pair (UTP) or shielded twisted-pair (STP) cable for RJ-45 connections: 100-ohm Category 3, 4 or 5 cable for 10 Mbps connections or 100-ohm Category 5 cable for 100 Mbps connections. Also be sure that the length of any twisted-pair connection does not exceed 100 meters (328 feet). The RJ-45 ports on the switch base unit support automatic MDI/MDI-X
TWISTED-PAIR CABLE AND PIN ASSIGNMENTS operation, you can use straight-through cables for all network connections to PCs or servers, or to other switches or hubs. In straight-through cable, pins 1, 2, 3, and 6, at one end of the cable, are connected straight through to pins 1, 2, 3, and 6 at the other end of the cable. When using any RJ-45 port on this switch, you can use either straight-through or crossover cable.. Pin MDI-X Assignment MDI Assignment 1 Input Receive Data + Output Transmit Data + 2 Input Receive Data - Output Transmit Data - 3 Output Transmit Data + Input Receive Data + 6 Output Transmit Data - Input Receive Data - 4,5,7,8 Not used Not used Note: The "+" and "-" signs represent the polarity of the wires that make up each wire pair. 1000BASE-T Pin Assignments All 1000BASE-T ports support automatic MDI/MDI-X operation, so you can use straight-through cables for all network connections to PCs or servers, or to other switches or hubs. The table below shows the 1000BASE-T MDI and MDI-X port pinouts. These ports require that all four pairs of wires be connected. Note that for 1000BASE-T operation, all four pairs of wires are used for both transmit and receive. Use 100-ohm Category 5, 5e or 6 unshielded twisted-pair (UTP) or shielded twisted-pair (STP) cable for 1000BASE-T connections. Also be sure that the length of any twisted-pair connection does not exceed 100 meters (328 feet). B-3
Page 1: TigerSwitch 10/100/1000 Gigabit Eth
Page 4 and 5: Information furnished by SMC Networ
Page 6 and 7: ii WARRANTIES EXCLUSIVE: IF AN SMC
Page 8 and 9: COMPLIANCES iv voltage limits and t
Page 10 and 11: COMPLIANCES vi Safety Compliance Wa
Page 12 and 13: COMPLIANCES viii
Page 14 and 15: CONTENTS x Connecting to a Power So
Page 16 and 17: CONTENTS xii
Page 18 and 19: ABOUT THE TIGERSWITCH 10/100/1000 S
Page 20 and 21: ABOUT THE TIGERSWITCH 10/100/1000 S
Page 22 and 23: ABOUT THE TIGERSWITCH 10/100/1000 O
Page 24 and 25: ABOUT THE TIGERSWITCH 10/100/1000 1
Page 26 and 27: NETWORK PLANNING Application Exampl
Page 28 and 29: NETWORK PLANNING Remote Connections
Page 30 and 31: NETWORK PLANNING Application Notes
Page 32 and 33: INSTALLING THE SWITCH Ethernet Cabl
Page 34 and 35: INSTALLING THE SWITCH Mounting 3-4
Page 36 and 37: INSTALLING THE SWITCH 3-6 3. If ins
Page 38 and 39: INSTALLING THE SWITCH Connecting to
Page 40 and 41: INSTALLING THE SWITCH 3-10
Page 42 and 43: MAKING NETWORK CONNECTIONS Connecti
Page 44 and 45: MAKING NETWORK CONNECTIONS Connecti
Page 46 and 47: MAKING NETWORK CONNECTIONS Cable La
Page 48 and 49: TROUBLESHOOTING Installation A-2 Ve
Page 52 and 53: CABLES 1000BASE-T MDI and MDI-X Por
Page 54 and 55: CABLES B-6
Page 56 and 57: SPECIFICATIONS C-2 Size 44.0 x 41.0
Page 58 and 59: SPECIFICATIONS C-4
Page 60 and 61: ORDERING INFORMATION D-2
Page 62 and 63: GLOSSARY Bandwidth The difference b
Page 64 and 65: GLOSSARY LAN Segment Separate LAN o
Page 66 and 67: GLOSSARY Glossary-6
Page 68 and 69: INDEX L port connections 4-1 power
Page 70: INDEX Index-4

TigerSwitch 10/100/1000 Installation Guide - SMC

Create successful ePaper yourself

Delete template?

Save as template?