TigerSwitch 10/100/1000 Installation Guide - SMC

More documents

Recommendations

Info

INSTALLING THE SWITCH 3-6 3. If installing a single switch only, turn to “Connecting to a Power Source” at the end of this chapter. 4. If installing multiple switches, mount them in the rack, one below the other, in any order. 5. If also installing RPUs, mount them in the rack below the other devices. Desktop or Shelf Mounting 1. Attach the four adhesive feet to the bottom of the first switch. RPU 1000=Yellow 100=Green 10=Flashing Green R01 TigerSwitch 10/100/1000 8624T 21 22 23 24 18 20 22 24 17 19 21 23 10 12 14 16 9 11 13 15 2 4 6 8 1 3 5 7 Figure 3-4. Attaching the Adhesive Feet 2. Set the device on a flat surface near an AC power source, making sure there are at least two inches of space on all sides for proper air flow. 3. If installing a single switch only, go to “Connecting to a Power Source” at the end of this chapter. 4. If installing multiple switches, attach four adhesive feet to each one. Place each device squarely on top of the one below, in any order. 5. If also installing RPUs, place them close to the stack.
Installing an Optional SFP Transceiver into the Switch TigerSwitch TigerSwitch 10/100/1000 10/100/1000 8624T 8624T RPU RPU 1000=Yellow 1000=Yellow 100=Green 100=Green 10=Flashing 10=Flashing Green Green R01 R01 Figure 3-5. Inserting an SFP Transceiver into a Slot To install an SFP transceiver, do the following: MOUNTING 1. Consider network and cabling requirements to select an appropriate SFP transceiver type. 2. Insert the transceiver with the optical connector facing outward and the slot connector facing down. Note that SFP transceivers are keyed so they can only be installed in one orientation. 3. Slide the SFP transceiver into the slot until it clicks into place. Note: SFP transceivers are hot-swappable. The switch does not need to be powered off before installing or removing a transceiver. However, always first disconnect the network cable before removing a transceiver. 3-7
Page 1: TigerSwitch 10/100/1000 Gigabit Eth
Page 4 and 5: Information furnished by SMC Networ
Page 6 and 7: ii WARRANTIES EXCLUSIVE: IF AN SMC
Page 8 and 9: COMPLIANCES iv voltage limits and t
Page 10 and 11: COMPLIANCES vi Safety Compliance Wa
Page 12 and 13: COMPLIANCES viii
Page 14 and 15: CONTENTS x Connecting to a Power So
Page 16 and 17: CONTENTS xii
Page 18 and 19: ABOUT THE TIGERSWITCH 10/100/1000 S
Page 20 and 21: ABOUT THE TIGERSWITCH 10/100/1000 S
Page 22 and 23: ABOUT THE TIGERSWITCH 10/100/1000 O
Page 24 and 25: ABOUT THE TIGERSWITCH 10/100/1000 1
Page 26 and 27: NETWORK PLANNING Application Exampl
Page 28 and 29: NETWORK PLANNING Remote Connections
Page 30 and 31: NETWORK PLANNING Application Notes
Page 32 and 33: INSTALLING THE SWITCH Ethernet Cabl
Page 34 and 35: INSTALLING THE SWITCH Mounting 3-4
Page 38 and 39: INSTALLING THE SWITCH Connecting to
Page 40 and 41: INSTALLING THE SWITCH 3-10
Page 42 and 43: MAKING NETWORK CONNECTIONS Connecti
Page 44 and 45: MAKING NETWORK CONNECTIONS Connecti
Page 46 and 47: MAKING NETWORK CONNECTIONS Cable La
Page 48 and 49: TROUBLESHOOTING Installation A-2 Ve
Page 50 and 51: CABLES Twisted-Pair Cable and Pin A
Page 52 and 53: CABLES 1000BASE-T MDI and MDI-X Por
Page 54 and 55: CABLES B-6
Page 56 and 57: SPECIFICATIONS C-2 Size 44.0 x 41.0
Page 58 and 59: SPECIFICATIONS C-4
Page 60 and 61: ORDERING INFORMATION D-2
Page 62 and 63: GLOSSARY Bandwidth The difference b
Page 64 and 65: GLOSSARY LAN Segment Separate LAN o
Page 66 and 67: GLOSSARY Glossary-6
Page 68 and 69: INDEX L port connections 4-1 power
Page 70: INDEX Index-4

TigerSwitch 10/100/1000 Installation Guide - SMC

Create successful ePaper yourself

Delete template?

Save as template?