Airetool Tube Cleaner and Expanders Catalog - Tecno Italia s.r.l

Model Number
General Accessories
Filters, Regulators, Lubricators
C
A
B
C
A
Filter Regulator Lubricator
NPT
Dimensions
Size Air Flow Bowl Capacity
A B C
In. SCFM m3/min. oz. liter in. mm in. mm in. mm
Filters
F02-M 1/4 35 9.9 5.0 0.15 5.6 142 3.0 76 0.9 23
F03-M 3/8 44 12.9 5.0 0.15 5.6 142 3.0 76 0.9 23
F04-M 1/2 138 39.1 10 0.30 6.4 163 3.4 86 1.0 25
Lubricators – Economist (Standard Mist)
L02-EP 1/4 28 3.7 5.0 0.15 4.8 122 3.0 76 1.6 41
L03-EP 3/8 48 6.2 5.0 0.15 4.8 122 3.0 76 1.6 41
L04-EP 1/2 102 13.6 10 0.30 5.4 137 3.4 86 1.6 41
Lubricators – Atomist (Fine Mist)
L02-AP 1/4 28 3.7 5.0 0.15 4.8 122 3.0 76 1.6 41
L03-AP 3/8 48 6.2 5.0 0.15 4.8 122 3.0 76 1.6 41
LO3-AP 1/2 102 13.6 10 0.30 5.4 137 3.4 86 1.6 41
Model Number
NPT
Size Air Flow
Pressure Range
(maximum)
A
Dimensions
B C
In. SCFM m3/min. psig bar in. mm in. mm in. mm
Regulators
RO2-G 1/4 80 10.8 125 8.5 3.9 99 3.0 76 1.3 33
RO3-G 3/8 80 10.8 125 8.5 3.9 99 3.0 76 1.3 33
R04-G 1/2 195 26.1 125 8.5 5.6 142 3.4 86 1.4 36
Modular Sleeve (with O-Ring)
Model: MS101
Unique modular sleeve design easily and
quickly connects one or more units and
accessories together without pipe nipples.
Hand tightening the threaded pin provides a
tight seal between the units. Modular sleeves
do not add length to combination
assemblies, and make a more compact
installation.
Modular Sleeve & Bracket (with O-Ring)
Model: MS101
Combination sleeve/wall mounting bracket as
shown. Designed for mounting a single unit or
combination of units directly to the wall. The
sleeve and mounting bracket can be ordered
assembled from the factory, or just the mounting
bracket alone to be used on existing modular
sleeves.
! Modular Construction
Modular End Blocks (sold in pairs)
Model: 1/4" NPTF – EB-102
3/8" NPTF – EB-103
1/2" NPTF – EB-104
3/4" NPTF – EB-106
The threaded End Blocks, together with the modular sleeves, allow a
single unit or a combination of units to be piped into the air system in
the modular mode. This feature allows ease of unit servicing or
replacement without disturbing the airline connections. End blocks
add 1.19" (30mm) to each end of the unit where used.
NOTE: The 3/4" end blocks are designed only to adapt to 3/4" piping
systems and do not increase flow ratings listed for any unit.
Automatic Drain Model: AD-101
Automatic Mechanical Drain is a float-type
mechanism with a 1/8" NPT threaded drain port completely
enclosed in the filter bowl. The float is
constructed of rigid cellular rubber. The
drain will operate automatically under air
pressure ranging from 20 to
175 psig (1.5 to 12 bar).
B
C
A
B
101