Aladin MKII Manual Ver 1.14 - Schneider Optics

More documents

Recommendations

Info

10 Introduction 2.3. Considerations regarding rf-channel selection with more than one working unit on a set If there are more then one ALADIN operated on set, care has to be taken regarding the selection of the rf-channel of each single receiver/ hand controller combination. It is not just important to select different channels but also to select channels which have enough space from each other in the channel raster. This avoids the physical effect of inter- modulation in the receivers and therefore prevents interference with each other. The table below is a suggestion which channels to select for up to 5 ALADINs operated simultaneously: Alternatively: Alternatively: Alternatively: Alternatively: ALADIN 1 Rf-Channel 0 ALADIN 1 Rf-Channel 0 ALADIN 2 Rf-Channel 8 ALADIN 2 Rf-Channel 1 ALADIN 3 Rf-Channel C/12 ALADIN 3 Rf-Channel 3 ALADIN 4 Rf-Channel E/14 ALADIN 4 Rf-Channel 7 ALADIN 5 Rf-Channel F/15 ALADIN 5 Rf-Channel D/13
3. Receiver / Motor Controller 3.1. Sockets/ Operation / Optical Signals Figure 1 - Motor Controller Front Panel Figure 2 - Motor Controller Rear Panel Full Color OLED Graphic Display Status LEDs RF-Error, Power, CAM-Relay Figure Figure 3 - Motor Motor Controller Controller Top Top 3.1.1. Sockets „MOTORS 1 – 8” (Lemo 7 Pin) Details 11 Connect external digital servo motors with incremental encoder, such as motors from the manufacturers BETZ-Tools, Hedén (M26VE), Scorpio, „Easylook System“ and Preston. 3.1.2. Socket „POWER/CAMERA“ (Lemo 2 and 5 pin) These sockets are used for the connection of the external power supply (voltage 10-30V). The Lemo 5pin also controls the start/stop-function of film and video cameras and accepts LTC time code signal for synchronizing the internal time code. 3.1.3. Sockets „AUX1 - 2“ Motor Status LEDs These sockets interface to the digital ENG-Lenses and other additional accessories like a controlling PC. Functions can be assigned within the setup menu. Membrane Keypad
Page 1: 333
Page 4 and 5: 4 Content Table of Contents 1. Intr
Page 6 and 7: 6 Introduction
Page 8 and 9: 8 Introduction 2. Short Overview 2.
Page 12 and 13: 12 Details 3.1.4. Socket „ANTENNA
Page 14 and 15: 14 Details 3.3. Receiver Menu Pleas
Page 16 and 17: 16 Details M2 Setup Link To: * Mode
Page 18 and 19: 18 Details … … Config: Config:
Page 20 and 21: 20 Details are addressed by an inde
Page 22 and 23: 22 Details 3.3.13.2. Lens Data Focu
Page 24 and 25: 24 Details 3.3.13.4. Lens Data Zoom
Page 26 and 27: 26 Details 3.3.14. Matching Setup S
Page 28 and 29: 28 Details Type Type of of Extensio
Page 30 and 31: 30 Details 5. Transmitter / Hand Co
Page 32 and 33: 32 Details 5.2. Transceiver-Module
Page 34 and 35: 34 Details Set Up RF-Channel Commun
Page 36 and 37: 36 Details Turn the hand wheel coun
Page 38 and 39: 38 Details 5.5.5. Zoom Scale (LED-B
Page 40 and 41: 40 Details Example: Drive lens ring
Page 42 and 43: 42 Advanced Features To switch the
Page 44 and 45: 44 Connections 8. Connection Exampl
Page 46 and 47: 46 Connections 8.2. Remote Control
Page 48 and 49: 48 Technical 10. Technical Informat
Page 50 and 51: 50 Technical 10.2. Electronic Calib
Page 52 and 53: 52 Technical 10.3.3. Electrical Cha
Page 54 and 55: 54 Documentation 10.5. Declarations
Page 56 and 57: 56 Documentation
Page 59: Documentation 59

Aladin MKII Manual Ver 1.14 - Schneider Optics

Create successful ePaper yourself

Delete template?

Save as template?