34169621 - heidenhain - DR. JOHANNES HEIDENHAIN GmbH

More documents

Recommendations

Info

Multipoint Axis Error Compensation 42 Selecting the compensation table, entering an axis correction SPEC FCT PARAMETER CODE ENT 1 0 5 2 9 6 ENT AXIS X X X FCT. X X SPEC FCT or ENT ENT Select special functions. Select the "Parameter" function if required, by repeatedly pressing the 1 2 key Select dialog for entering the code number. Enter code number 105296 and confirm with ENT. Enter the axis causing the error (e.g. X) (screw pitch error), and confirm with ENT. DATUM X 2 7 SPACING X 1 0 27.000 ENT 0 0 1 28.024 ENT SPEC FCT or ENT ENT ENT Enter the active datum for the error on the axis to be corrected (e.g. 27 mm) and confirm with ENT. Enter the spacing of the compensation points on the axis to be corrected, for example 2 10 µm (equals 1024 mm) and confirm with ENT. Compensation point no. 1 is displayed. Enter the associated compensation value (e.g. 0.01 mm) and confirm with ENT. Enter all further compensation points. If you press the minus key, the unit will show the number of the current compensation point in the X display. Conclude entry.
Deleting a compensation value table SPEC FCT PARAMETER CODE ENT AXIS X Z SPEC FCT or 1 0 5 2 9 6 ENT DELETE Z ENT SPEC FCT Select special functions. Select “parameter.” Select the dialog for entering the code number. Enter the code number 105296 and confirm with ENT. Select the compensation value table (e.g., for the Z axis), and delete the table. Confirm with ENT, or cancel with CL. Conclude entry. Multipoint Axis Error Compensation 43
Page 1 and 2: User’s Manual Position Display Un
Page 3 and 4: This manual is for the ND display u
Page 5 and 6: Datum setting The workpiece drawing
Page 7 and 8: Nominal position, actual position a
Page 9 and 10: Switch-On, Traversing the Reference
Page 11 and 12: SPEC FCT SPEC FCT or PROBING ENT PR
Page 13 and 14: Datum Setting with the KT Edge Find
Page 15 and 16: X PROBE X (appears only briefly) 5
Page 17 and 18: PROBE MIDP. X ENT If required, sele
Page 19 and 20: Moving the Axes with Distance-To-Go
Page 21 and 22: Bolt Hole Circles and Bolt Circle S
Page 23 and 24: HOLE DEPTH 5 START SPEC FCT ENT ENT
Page 25 and 26: SPEC FCT LIN. HOLE ENT 1ST HOLE X 2
Page 27 and 28: Working with Scaling Factors Scalin
Page 29 and 30: Part II Installation and Specificat
Page 31 and 32: Connections on Rear Panel ID label
Page 33 and 34: Connecting the Encoders Your displa
Page 35 and 36: List of Operating Parameters P1 Uni
Page 37 and 38: P80 Function of the CL key Set to z
Page 39 and 40: Parameter settings for HEIDENHAIN l
Page 41: Multipoint Axis Error Compensation
Page 45 and 46: RS-232-C/V.24 (Option) In addition
Page 47 and 48: Measured value output when probing
Page 49 and 50: Measured value output over the cont
Page 51 and 52: Example of measured value output ov
Page 53 and 54: Dimensions in mm/inches Tilting bas

34169621 - heidenhain - DR. JOHANNES HEIDENHAIN GmbH

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?