PK Series Manual (English, 2005) - Forgotten Weapons

More documents

Recommendations

Info

In order to prepare the link belt loader for use, it is necessary to do the following: 1) Remove the loader parts from the box. 2) Fasten the handle with the locking device. 3) Set up the base and fasten it to a table or to the side of the loader. 4) Set up the link belt feed. 5) Fill the basket with cartridges so that they lie across the width of the basket. 6) Lift the lid of the receptacle and insert the link belt with the cutouts on the links facing downward. 7) Insert a cartridge into the first link by hand and place the link belt with the cartridge opposite the feed; close the receptacle lid (see figure 6-16). Figure 6-16. Link Belt Loader Prepared for Use In order to load the link belt with cartridges turn the handle clockwise with your right hand at an even speed and add ammunition to the basket with your left hand so that it lies across the width of the basket. When loading the link belt, attention must be paid that the link belt does not twist. During loading, the cartridges fall by their own weight into the narrow part of the conduit where the feed mechanism takes hold of them and pushes them out of the chute. The cartridge is passed forward along the conduit and then falls onto the bottom from where the feed mechanism aligns it with the link when the handle is turned around again. When the feeder returns to the rear position, its lever moves the link belt feeder which presses it into the link belt and moves it by one link. UNCLASSIFIED VI - 11
In order to pack the link belt loader into the wooden box, it is necessary to do the following: 1) Release the latch and move the handle along the length of the loader over the feed mechanism. 2) Raise the clamp and fasten it with the machine bolt. 3) Place the handle between the bifurcation and the clamp machine bolt and place the components in the wooden box. UNCLASSIFIED VI - 12
Page 1 and 2:
NATIONAL GROUND INTELLIGENCE CENTER
Page 3 and 4:
PURPOSE PREFACE This publication pr
Page 5 and 6:
Section I. General The Soviet/Russi
Page 7 and 8:
PKS: The basic PK mounted on a trip
Page 9 and 10:
PKMS: The PKMS (see figures 1-6 1-
Page 11 and 12:
Figure 1-10. Bulgarian MG-M1S (PKMS
Page 13 and 14:
Description of the PK Machinegun Co
Page 15 and 16:
Flash Suppressor. The flash suppres
Page 17 and 18:
Along the bottom, the receiver fram
Page 19 and 20:
Figure 1-18. Barrel Lock Assembly R
Page 21 and 22:
Figure 1-20. Feed Tray Assembly On
Page 23 and 24:
Figure 1-22. Gas Block Assembly The
Page 25 and 26:
Gas Cylinder. The gas cylinder (see
Page 27 and 28:
Slide and Piston Assembly. The slid
Page 29 and 30:
Front Sight Assembly. The front sig
Page 31 and 32:
Sight Bar Assembly. The sight bar a
Page 33 and 34:
Tripod Assembly. The tripod serves
Page 35 and 36: and has longitudinal ribs which all
Page 37 and 38: Figure 1-36. Cradle Mount & Base d)
Page 39 and 40: Section II. Technical Data All tech
Page 41 and 42: An improperly loaded cartridge (see
Page 43 and 44: Figure 3-5. Receiver Cover Properly
Page 45 and 46: Clearing the PK Machinegun. Keep th
Page 47 and 48: Figure 3-7. Barrel Locking Latch in
Page 49 and 50: Zeroing the PK-series Machinegun. L
Page 51 and 52: In order to fire, the gunner, while
Page 53 and 54: • Zeroing the weapon is conducted
Page 55 and 56: checked again in order to establish
Page 57 and 58: Figure 4-2. Feed Tray Cover Open Fi
Page 59 and 60: Remove the Operating Rod Assembly (
Page 61 and 62: Remove the Bolt and Carrier: Grasp
Page 63 and 64: Removing the Bolt from the Carrier:
Page 65 and 66: Removing the Barrel from the Receiv
Page 67 and 68: PK Machinegun Field Stripped. The P
Page 69 and 70: Figure 5-2. Gas Escape Chamber Alig
Page 71 and 72: Replace the Bolt into the Carrier:
Page 73 and 74: With Receiver Group Grooves Figure
Page 75 and 76: Close the Feed Tray Cover: Grasp th
Page 77 and 78: Figure 6-1. 100- and 250- Cartridge
Page 79 and 80: Carrying Case. The carrying case (s
Page 81 and 82: The slings for carrying the tripod
Page 83 and 84: Oil Can. The oil can (see figure 6-
Page 85: Link Belt Loader. The link belt loa
Page 89 and 90: • The presence of corrosion, scra
Page 91 and 92: cocking level tooth catches is not
Page 93 and 94: Listed in table 7-1 are the establi
Page 95 and 96: Malfunctions and their Characterist
Page 97 and 98: Section VIII. Service and Training
Page 99 and 100: M1908 7.62 x 54R-mm Ammunition Bull
Page 101 and 102: M1908 7.62 x 54R-mm Ammunition Head
Page 103 and 104: Figure 8-7. Three-Element, 3 x 120
Page 105 and 106: Figure 8-11. Single Segment Headsta
Page 107 and 108: • Listed below in table 8-3 are t
show all

PK Series Manual (English, 2005) - Forgotten Weapons

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?