You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
Preassembly<br />
<strong>Unit</strong> 3—Short Top Foil<br />
If top foil is shorter than 93/4" (248 mm), use one of the following special techniques to ensure sufficient bearing<br />
surface for the foil in the area of the halyard swivel.<br />
UNIT 3<br />
9 3 /4" (248 mm)<br />
9 3 /4" (248 mm) No special treatment required.<br />
9 5 /8"–7 1 /8" (244–181 mm)<br />
9 5 /8"–7 1 /8" (244–181 mm) Do not use plastic bushing<br />
above top connector.<br />
7"–5 1 /2" (178–140 mm)<br />
7"–5 1 /2" (178–140 mm) Do not use plastic bushing<br />
above top connector. Shorten top of connector and if<br />
necessary shorten trim cap.<br />
5 3 /8"–4" (137–102 mm)<br />
Cut-Offs<br />
Do Not Use<br />
Cut-Offs – Do Not Use<br />
Cut-Offs<br />
Do Not Use<br />
5 3 /8"–4" (137–102 mm) Do not use plastic bushing<br />
above top connector. Cut connector right at cross formed<br />
by glue dispersion channels. Use single foil screw in top<br />
foil only.<br />
18 MKIV Underdeck <strong>Unit</strong> 3<br />
3 1 /2" (89 mm)<br />
3" (76 mm)<br />
2 1 /2" (64 mm)<br />
2" (51 mm)<br />
1 1 /2" (38 mm)<br />
Top Foil<br />
Length from<br />
Worksheet<br />
3 1 /2"<br />
(89 mm)<br />
3"<br />
(76 mm)<br />
2 1 /2"<br />
(64 mm)<br />
2"<br />
(51 mm)<br />
1 1 /2"<br />
(38 mm)<br />
Under 1 1 /2" (38 mm)<br />
1. Initial<br />
top foil<br />
cut length<br />
6 9 /16"<br />
(167 mm)<br />
6 1 /16"<br />
(154 mm)<br />
6 9 /16"<br />
(167 mm)<br />
5 1 /16"<br />
(129 mm)<br />
4 9 /16"<br />
(116 mm)<br />
2. Cut through<br />
middle hole in<br />
top foil.*<br />
Resulting Top<br />
Foil Length<br />
5"<br />
(127 mm)<br />
4 1 /2"<br />
(114 mm)<br />
4"<br />
(102 mm)<br />
3 1 /2"<br />
(89 mm)<br />
3"<br />
(76 mm)<br />
Cut-Offs<br />
Do Not Use<br />
3 1 /2"–1 1 /2" (89–38 mm) Shorten top foil and adjoining<br />
full length foil so two screws are used to assemble joint<br />
instead of four. Do not use plastic bushings above top<br />
connector.<br />
3. Shorten<br />
full length<br />
adjoining<br />
foil by<br />
cutting<br />
through<br />
middle<br />
hole.*<br />
4. Shorten<br />
connector<br />
Length<br />
4 7 /8"<br />
(124 mm)<br />
4 7 /8"<br />
(124 mm)<br />
4 7 /8"<br />
(124 mm)<br />
4 3 /8"<br />
(111 mm)<br />
3 3 /4"<br />
(95 mm)<br />
*To allow for saw cut, position blade so upper half of<br />
middle hole is preserved.<br />
Under 1 1 /2" (38 mm) Eliminate top foil and run foil<br />
higher in torque tube.<br />
5. Shorten<br />
trim cap<br />
No<br />
No<br />
No<br />
Yes<br />
Yes<br />
Cut-Off<br />
Do Not Use