CaprizPlus Instructions for use - Heatline

More documents

Recommendations

Info

Fault codes Description Cause Solution F00 Flow heating temperature sensor fault Sensor open circuit F01 Return heating temperature sensor fault Return heating temperature sensor disconnected F10 Flow heating temperature sensor fault Sensor short-circuit F11 Return heating temperature sensor fault Return heating temperature sensor shorted. F20 F22 F23 F24 Overheating fault Water pressure of the installation (
Fault codes Description Cause Solution F73 Heating circuit pressure sensor fault The sensor is shorted or disconnected. • Check the sensor’s connections. F74 Heating circuit pressure sensor fault Fault in pressure sensor • Check the sensor. F76 F77 F83 F84 F85 F86 Thermal fuse fault Fault in gas valve motor. No water in the installation : the temperature does not increase when the burner is lit Permanent temperature difference between fl ow and return heating sensors Flow and return heating sensors fault Underfl oor heating contact fault Thermal fuse disconnected Defective thermal fuse Defective gas valve. Defective condensate pump (option) Return water valve closed Pump disconnected Leak in the installation Inverted or disconnected fl ow and return heating temperature sensors Defective temperature sensors Flow and return heating temperature sensor connected to same tube Floor heating contact open Sensor disconnected or defective Err User interface fault Defective user interface • Check the fuses connections. • Replace the heat exchanger. • Check the gas valve connections. • Check the operation of the gas valve. • Check the operation of the condensate pump (option). • Fill the installation. • Purge the installation. • Check the pump connections. • Check the fl ow and return heating sensor connections. • Check that there are no leaks. • Check temperature sensors connections. • Replace faulty sensors. • Check temperature sensors connections. • Check the sensor connections. • Check that the sensor is connected to the main board and the shunt is removed. • Check connection from user interface PCB to main PCB. • Replace user interface. 15.4 Functional flow diagram 15.4.1 Central Heating Service Call 0844 736 9138, Technical Help (Chargeable) Call 0906 802 0253 - 31 -
Page 1 and 2: 16 17 18 19 11 22 10 23 9 8 7 1 6 2
Page 3 and 4: INTRODUCTION 1 Instructions guidanc
Page 5 and 6: 19 Ignition module 20 Heating flow
Page 7 and 8: 4.2 Appliance Most of the appliance
Page 9 and 10: 7 Appliance installation 7.1 Scope
Page 11 and 12: The fl ue is designed with an inter
Page 13 and 14: Service Call 0844 736 9138, Technic
Page 15 and 16: 9 Evacuation of combustion products
Page 17 and 18: 9.2 Flue configuration description
Page 19 and 20: 230V permanent supply + 230V system
Page 21 and 22: 11 Commissioning At the time of com
Page 23 and 24: Operational Gas Inlet Pressure In c
Page 25 and 26: 13 Installation settings • To adj
Page 27 and 28: 13.1.2 Test modes By activating the
Page 29: 15.1.2 Check the gas supply 1 15.2
Page 33 and 34: 17 Draining 17.1 Heating circuit
Page 35 and 36: 2A Flue elbow 2B Vertical flue adap
Page 37 and 38: 18.8 Condensate trap a Warning: 3 5
Page 39 and 40: 18.9.1 Spark electrode • Disconne
Page 41 and 42: 19.4 Hydraulic block 31 32 33 34 9
Page 43 and 44: 19.5 Combustion block 19 20 21 18 1
Page 45 and 46: When reconnecting, the polarity of
Page 47 and 48: 20 Spare parts In order to guarante
Page 50 and 51: Failure to install and commission a
Page 52: 0020112883-03 06/11 Heatline, Notti

CaprizPlus Instructions for use - Heatline

Create successful ePaper yourself

Delete template?

Save as template?