Building instructions Pober Pixie - aero-naut Modellbau

More documents

Recommendations

Info

Pober Pixie Dangers and hazards Model flying, especially under radio control, is a fascinating pastime. When you are operating your model we recommend that you make a point of observing the following basic rules, to avoid annoying or injuring other model flyers and anybody else. When you are operating a model aircraft you bear sole responsibility for your behaviour and for any consequences of your behaviour. For this reason it is essential that you take out a private third-party insurance policy or a special model flying policy. Ask your local model shop for details, or contact your regional or national model flying association (BMFA in U.K.). You may need to register your radio control system (varies from country to country) before using it. Once again, your local model shop will gladly give you information on this. Build your model carefully, checking every procedure, and be sure that everything is safely secured. Check that the entire model is safe to fly before each flight. Only fly your model at an approved location, e.g. a model flying site, at which your activity will not cause a nuisance or hazard to other modellers or anybody else in the vicinity. Gliders and electricpowered models are far less critical in these respects. Glow motors should only be operated with the recommended silencer fitted. Read the safety recommendations supplied by the motor manufacturer. Never fly directly towards or over spectators, and don’t be tempted to carry out flashy, high-risk manoeuvres. Don’t switch on your transmitter until you have ensured that no other radio control system in the vicinity is operating on the same frequency. We hope you have many hours of fun and pleasure with your Pober Pixie. Happy landings! aero-naut Modellbau Parts List No. Part Description No. off 1 GRP fuselage White GRP fuselage, factory-fitted cabane 1 2 Cowl Ready made, vac. moulded ABS 1 3 Port outboard wing panel Built-up balsa structure, ready made 1 4 Starboard outboard wing panel Built-up balsa structure, ready made 1 5 Wing centre section Built-up balsa structure, ready made 1 6 Tailplane Balsa, ready made 1 7 Left elevator Balsa, ready made 1 8 Right elevator Balsa, ready made 1 9 Fin Balsa, ready made 1 10 Fin strake (front fairing) Balsa, ready made 1 11 Rudder Balsa, ready made 1 12 Balsa block for undercarriage Balsa, ready made, 20 x 122 x 50 mm 1 13 Strut support Profiled hardwood strip, ready made 1 14 Undercarriage support Plywood, 3 x 49.5 x 118 1 15 Undercarriage retaining nut support Plywood, 3 x 15 x 15 2 16 Battery support Plywood, 3 x 45 x 220 1 17 Servo plate – wing Plywood, 3 x 68 x 68 2 18 Servo plate – fuselage Plywood, 3 x 80 x 135 1 19 Servo plate support – wing Spruce, 4 x 12 x 68 4 20 Servo plate support – fuselage Spruce, 5 x 5 x 80 4 21 Slotted tailwheel support Obechi, 10 x 17 x 30, ready made 1 22 Upper hatch latch Profiled balsa strip 2 23 Strut support, fuselage GRP, ready made, 2 x 10 x 140 2 24 Strut support GRP, ready made, 2 x 10 x 35 + 22 4 Pober Pixie building instructions 10
Pober Pixie 25 Access hatch ABS 1 27 Reinforcing strip – tailplane / fin Balsa triangular strip, 8 x 8 x 120 2 28 Reinforcement Obechi, 10 x 10 x 150, overlength 1 29 Cockpit reinforcement Balsa, 19 x 19 x 30 1 30 Motor mount – side panel Plywood, ready made 2 31 Motor mount – front part Plywood, ready made 1 32 Motor mount reinforcement – front part Spruce triangular strip, ready made 1 33 Motor mount – fuselage reinforcement Balsa triangular strip, ready made 1 34 Motor mount top reinforcement Plywood 2 35 Balsa block For motor mount installation 1 36 Screw-hook – for cockpit Metal - ready made 2 37 M2 ball-link Ready made 1 38 M2 ball-link ball Ready made 1 39 Tension spring Ready made 1 40 Threaded rod Ready made, M2 x 330, overlength 1 41 Elevator joiner Ready made, steel 2 mm 1 42 Metal M2 clevis Ready made 16 43 M2 threaded rod, 200 long Ready made 7 44 M2 nut Ready made 18 45 Rudder / elevator horn, 18 mm Ready made 2 46 GRP aileron horn Ready made 2 47 Self-tapping screw, 2.5 x 13 Ready made 12 48 Nylon M5 screw for undercarriage Ready made 2 49 M3 captive nut Ready made 3 50 Steel screw with integral washer, M3 x 12 Ready made 2 51 Steel screw with integral washer, M3 x 25 Ready made 1 52 Brass tube Ready made, 5/4 x 108 mm 2 53 Steel rod Ready made, 4 x 40 mm 4 54 Self-tapping screw with integral washer Ready made 7 55 Brass tube Ready made, 4/3 x 17 mm 1 56 Nylon M5 nut for undercarriage Ready made 2 57 Rudder hinge Ready made 2 58 Wing joiner hook Steel - ready made 2 59 Main undercarriage unit Ready made 1 60 Profiled strip – wing strut Ready made, obechi, 480 mm 4 61 Wheel spat Vac. moulded ABS 1 62 Pushrod Balsa, 8 x 8 x 700 mm 2 63 Wheel Ready made, 60/19 mm 2 64 M4 nut Undercarriage 4 65 Steel screw, M4 x 35 Undercarriage - wheel axle 2 66 M4 self-locking nut Undercarriage - wheel nut 2 67 Tailwheel unit Complete set 1 68 Cockpit Ready made 1 69 Building instructions 1 70 Plan 1 71 Decal sheet Ready made 2 Pober Pixie building instructions 11
Page 1 and 2: Pober Pixie Building instructions P
Page 3 and 4: Pober Pixie Sand the internal surfa
Page 5 and 6: Pober Pixie • Slit and peel off a
Page 7 and 8: Pober Pixie • Screw the centre se
Page 9: Pober Pixie RC installation, finish

Building instructions Pober Pixie - aero-naut Modellbau

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?