TK-880/H (UHF) mobile service manual - The Repeater Builder's ...
TK-880/H (UHF) mobile service manual - The Repeater Builder's ...
TK-880/H (UHF) mobile service manual - The Repeater Builder's ...
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
REALIGNMENT<br />
<strong>TK</strong>-<strong>880</strong>/H<br />
Notes :<br />
• To start the Firmware Programmer from KPG-49D, the<br />
FPRO path must be set up by KPG-49D setup.<br />
• This mode cannot be entered if the Firmware programming<br />
mode is set to Disable in the Programming software<br />
(KPG-49D).<br />
• When programming the firmware, it is recommend to<br />
copy the data from the floppy disk to your hard disk before<br />
update the radio firmware.<br />
Directly copying from the floppy disk to the radio may not<br />
work because the access speed is too slow.<br />
6-4. Function<br />
1. If you press the [MON] switch while “PROG 57600” is<br />
displayed, the checksum is displayed. If you press the<br />
[MON] switch again while the checksum is displayed,<br />
“PROG 57600” is redisplayed.<br />
2. If you press the [D] switch while “PROG 57600” is displayed,<br />
the display changes to “PROG 19200” to indicate<br />
that the write speed is low speed (19200 bps). If you<br />
press the [D] switch again while “PROG 19200” is displayed,<br />
the display changes to “PROG 38400”, and the<br />
write speed becomes the middle speed (38400 bps). If<br />
you press the [D] switch again while “PROG 38400” is<br />
displayed, the display returns to “PROG 57600”.<br />
Note :<br />
Normally, write in the high-speed mode.<br />
How to enter the password with the [System up/down]<br />
key (Trunking format), the [Group up/down] key (Conventional<br />
format);<br />
If the [System up/down] key (Trunking format), the<br />
[Group up/down] key (Conventional format) is pressed<br />
while “CLONE LOCK” is displayed, numbers (0 to 9) are<br />
displayed flashing. When you press the [SCN] key, the<br />
currently selected number is determined, and the display<br />
shifts to the left. If you press the [SCN] key after entering<br />
the password in this procedure, “CLONE MODE” is displayed<br />
if the entered password is correct. If the password<br />
is incorrect, “CLONE LOCK” is redisplayed.<br />
4. Power on the slave <strong>TK</strong>-<strong>880</strong>/<strong>880</strong>H.<br />
5. Connect the cloning cable (No. E30-3382-05) to the<br />
modular microphone jacks on the master and slave.<br />
6. Press the [S] key on the master while the master displays<br />
“CLONE MODE”. <strong>The</strong> data of the master is sent to the<br />
slave. While the slave is receiving the data, “PRO-<br />
GRAM” is displayed. When cloning of data is completed,<br />
the mater displays “END”, and the slave automatically<br />
operates in the User mode. <strong>The</strong> slave can then be operated<br />
by the same program as the master.<br />
7. <strong>The</strong> other slave can be continuously cloned. When the<br />
[S] key on the master is pressed while the master displays<br />
“END”, the master displays “CLONE MODE”.<br />
Carry out the operation in step 4 to 6.<br />
Note :<br />
Only the same models can be cloned together.<br />
7. Clone Mode<br />
Programming data can be transferred from one radio to<br />
another by connecting them via their modular microphone<br />
jacks. <strong>The</strong> operation is as follows (the transmit radio is the<br />
master and the receive radio is a slave).<br />
1. Turn the master <strong>TK</strong>-<strong>880</strong>/<strong>880</strong>H power ON with the [C] key<br />
held down. If the password is set to the <strong>TK</strong>-<strong>880</strong>/<strong>880</strong>H,<br />
the <strong>TK</strong>-<strong>880</strong>/<strong>880</strong>H displays “CLONE LOCK”. If the password<br />
is not set, the <strong>TK</strong>-<strong>880</strong>/<strong>880</strong>H displays “CLONE<br />
MODE”.<br />
2. When “CLONE LOCK” is displayed, only the [System up/<br />
down] key (Trunking format), the [Group up/down] key<br />
(Conventional format) and [SCN], and [0] to [9] keys can<br />
be accepted. When you enter the correct password, and<br />
“CLONE MODE” is displayed, the <strong>TK</strong>-<strong>880</strong>/<strong>880</strong>H can be<br />
used as the cloning master. <strong>The</strong> following describes how<br />
to enter the password.<br />
3. How to enter the password with the microphone keypad.<br />
If you press a key while “CLONE LOCK” is displayed, the<br />
number that was pressed is displayed on the <strong>TK</strong>-<strong>880</strong>/<br />
<strong>880</strong>H. Each press of the key shifts the display in order to<br />
the left. When you enter the password and press the<br />
[SCN] key, “CLONE MODE” is displayed if the entered<br />
password is correct. If the password is incorrect,<br />
“CLONE LOCK” is redisplayed.<br />
Cloning cable<br />
(E30-3382-05)<br />
Fig. 2<br />
17