AdrenalineMoto - PU STREET 2014.pdf.pdf

www.partsnetweb.com
LIGHTING
EXHAUST
LUGGAGE
AUDIO &
VIDEO
PENTASTAR-
XP TURN
SIGNAL/BRAKE
LIGHT SYSTEM
MODULE
•All the features of a self-canceling turn signal module with the addition
of a turn signal to brake light module
•Applying the brakes lights the rear turn signals and holds until brakes
are released; turn signal flash has priority over brake lights
•Features three turn signal timing modes: a one-second press of the
turn signal button causes seven seconds of turn signal flash before selfcancel,
a two-second press causes 20 seconds of flash before self-cancel
and a four-second press causes 75 seconds of flash before self-cancel
•All flash modes can be cancelled with a second push of the turn
signal button
•Flash time is consistent whether using incandescent or LED lighting
•Simultaneous depression of right and left turn signal buttons for one
second begins hazard mode; flash continues until manually cancelled
•Solid-state electrical components with weather-proof, soft cell
technology to prevent wire damage
•Runs from 12V power source at 6A per channel
•Measures 2 1 /4” L x 1 5 /8” W x 5 /8” H
•Mounts easily with included double-sided tape
•Designed for use with individual momentary-type turn signal switches
mounted on left and right bars; will not work on models with left and
right turn signal switch built into one unit that requires push to cancel
•Made in the U.S.A.
BRAKE HOLD MODULE
•Keeps brake lights lit after you’ve released your brakes but are still
decelerating; also keeps them lit while stopped
•Features two modes: when brakes are applied, emits three short
light flashes followed by one long flash (3.5 sec.) and repeats until
acceleration or, when brakes are applied, emits five short flashes
followed by a constant on until acceleration
•Brake alert feature allows you to get the attention of someone behind
you while the module is holding the brake lights on; press the brake
and the lights will flash five times
•Connects to bike’s electronic speed pick-up sensor; will not work with
cable-driven speedometers
•Installs inline on the wire leading to the brake light; connect to a
switched power source and ground wire, then tap a wire into
speed sensor
•Sealed, weather-resistant heat sink case
•Runs from 12V power source at a max 10A
•Measures 2 1 /4” L x 1 5 /8” W x 5 /8” H
•Not for integrated brake/turn
•Made in the U.S.A.
SUG. RETAIL .........$109.95 PART # 2050-0062 SUG. RETAIL ............$64.95 PART # 2050-0063
“BACK OFF”
WIG WAG
BRAKE LIGHT
MODULATOR
FOR MODELS WITH
TWIN BRAKE LIGHTS
All part numbers in BOLD MAGENTA
are new this year.
“BACK OFF”
XP BRAKE
LIGHT
MODULATOR
•Compact, solid-state
electronic module converts
brake lights into two choices of
visual alerting signals
•Mode one emits four quick,
alternating flashes of left and right brake
light followed by three short flashes and
one long flash of both brake lights; pattern of
three short flashes and one long flash of both lights repeats as long as
brakes are applied
•Mode two emits four quick, alternating flashes of the left and right
brake lights followed by three short flashes of both brake lights and
then a steady on; brake lights remain on until brakes are released
•Specifications: 12V DC, max. capacity 10A, sealed weather-resistant heat
sink case, 2 1 /4” L x 1 5 /8” W x 5 /8” H
•Not for integrated brake/turn
•Made in the U.S.A.
SUG. RETAIL ............$42.95 PART # 2050-0031 SUG. RETAIL ............$42.95
“BACK OFF” MC BRAKE LIGHT MODULATOR
•This compact, solid-state electronic module converts your ordinary brake light into an attention-getting,
visual alerting device
•Module causes three short flashes, stays on for 3.5 seconds, then repeats the cycle for as long as the
brake is on
•Specifications: 12V DC, max. capacity 10A, sealed weather-resistant heat sink case, 2 1 /4” L x 1 5 /8” W x 5 /8” H
•Not for integrated brake/turn
•Made in the U.S.A.
SUG. RETAIL .............................$37.95 PART #
DS-272352
2014 PARTS UNLIMITED STREET
•Compact, solid state
electronic module
converts brake lights
into two choices of visual
alerting signals when brakes
are applied
•Mode one emits three short flashes followed by one long flash (3.5
seconds); repeats as long as brakes are applied
•Mode two emits five short flashes followed by a steady on light; light
remains on until brakes are released
•Specifications: 12V DC, max. capacity 10A, sealed weather-resistant heat
sink case, 2 1 /4” L x 1 5 /8” W x 5 /8” H
•Not for integrated brake/turn
•Made in the U.S.A.
PART # 2050-0030
COVERS &
SECURITY
GENERAL
ACCESSORIES
WINDSHIELDS
FAIRINGS &
BODY
SEATS &
SISSY BARS
HANDLEBARS &
HAND CONTROLS
FOOTPEGS &
FOOT CONTROLS
LIGHTING
ELECTRICAL
& GAUGES
SPROCKETS
CHAINS
WHEELS &
ACCESSORIES
BRAKES
SUSPENSION
ENGINE
FUEL/AIR
SYSTEMS
CHEMICALS
& LUBES
HARDWARE
& TOOLS
TRANSPORT &
TRAILER
MERCHANDISING
CROSS
REFERENCE
INDEX
767