Virtual Connect SAN Cookbook.pdf - Sallustio.ch

More documents

Recommendations

Info

The Virtual Connect 8Gb 24-Port Fibre Channel module supports up to 8 SAN fabrics: Fabric 6 Fabric 7 Fabric 5 Fabric 8 VC-FC 8Gb 24-Port Module Fabric 1 Fabric 4 Fabric 2 Fabric 3 The Virtual Connect FlexFabric module supports up to 4 SAN fabrics: VC-FlexFabric Module Fabric 1 Fabric 4 Fabric 2 Fabric 3 Considerations and concepts 16
12Vdc HP StorageWorks 4/32B SAN Switch 0 4 1 5 2 6 3 7 8 12 9 13 10 14 1 15 16 20 17 21 18 2 19 23 24 28 25 29 26 30 27 31 UID HP 4Gb VC-FC Module PS 1 Cntrl 1 1 2 DP1-A DP1-B 1 2 DP1-A DP1-B 1 2 3 4 12Vdc UID Mfg Mgmt HP ProLiant BL460c UID NIC 1 NIC 2 UID Cntrl 2 HP 4Gb VC-FC Module UID UID 12Vdc Mfg PS 2 HP StorageWorks 4/32B SAN Switch 0 4 1 5 2 6 3 7 8 12 9 13 10 14 1 15 16 20 17 21 18 2 19 23 24 28 25 29 26 30 27 31 1 2 3 4 12Vdc NPIV For Fibre Channel connections, HP VC 4Gb FC module, HP VC 8Gb 24-Port FC module, HP VC 8Gb 20- Port FC module or HP VC FlexFabric 10Gb/24-port module uplinks can be connected only to Fibre Channel switch ports that support N_port_ID virtualization (NPIV). The use of NPIV allows the VC-FC modules to be connected to any switch supporting the NPIV protocol like data center Brocade, McData, Cisco, and Qlogic FC switches. To verify that NPIV support is provided and for instructions on enabling this support see the firmware documentation that ships with the Fibre Channel switch. The SAN switch ports connecting to the VC Fabric uplink ports must be sometimes configured to accept NPIV logins, see "Appendix C: Brocade SAN switch NPIV configuration" or "Appendix D: Cisco SAN switch NPIV configuration" or "Appendix E: Cisco NEXUS SAN switch NPIV configuration" depending on your switch model. Figure 4: NPIV requires a SAN switch between the VC Fabric uplink ports and the Storage Disk Array Storage Array Fabric-1 Fabric-2 HBA 1 HBA 2 Blade Server Considerations and concepts 17
Page 1 and 2: HP Virtual Connect Fibre Channel Ne
Page 3 and 4: Contents About this document ......
Page 5 and 6: Summary ...........................
Page 7 and 8: Considerations and concepts Key tak
Page 9 and 10: Virtual Connect Fibre Channel suppo
Page 11 and 12: Supported VC SAN Fabric configurati
Page 13 and 14: 10/100Base-TX 6 15 16 13 14 11 12 9
Page 15: Multiple-fabric Support Support for
Page 19 and 20: Port Group Beginning with version 1
Page 21 and 22: Uplink port path failover: The modu
Page 23 and 24: Link stability This interval define
Page 25 and 26: Scenario 1: Simplest scenario with
Page 27 and 28: For more information about configur
Page 29 and 30: 4. Create a new VC Fabric named Fab
Page 31 and 32: Blade Server configuration Server p
Page 33 and 34: NOTE: Static Login Distribution has
Page 35 and 36: 12Vdc HP StorageWorks 4/32B SAN Swi
Page 37 and 38: 1. Create a VC SAN Fabric by select
Page 41 and 42: Blade Server configuration Server p
Page 45 and 46: Defining a new VC SAN Fabric via GU
Page 49 and 50: 7. Four VC fabrics have been create
Page 51 and 52: 2. Under FC SAN Connections, select
Page 53 and 54: Scenario 4: Multiple VC SAN fabrics
Page 55 and 56: Considerations Each Virtual Connect
Page 57 and 58: first VC-FC module (Bay 5). 3. On t
Page 59 and 60: 6. Then identically, create two VC
Page 61 and 62: 2. Enter the following commands to
Page 63 and 64: The VC module uplink ports are phys
Page 67 and 68:
Figure 18: FlexFabric Module port c
Page 69 and 70:
Defining a new VC SAN Fabric via GU
Page 71 and 72:
4. Select either Manual or Automati
Page 73 and 74:
7. Two VC fabrics have been created
Page 75 and 76:
Defining a new VC SAN Fabric via CL
Page 77 and 78:
Scenario 6: Adding VC Fabric uplink
Page 79 and 80:
a. For a Brocade SAN switch: Portsh
Page 81 and 82:
3. The upstream SAN switch shows th
Page 83 and 84:
2. Click Add Port, select the port
Page 85 and 86:
Figure 26: Hot adding one uplink po
Page 87 and 88:
2. Click on the Server connections
Page 89 and 90:
Summary This scenario demonstrates
Page 91 and 92:
2. Click the DPVM Setup icon. The D
Page 93 and 94:
7. Select all VC-FC fabric devices
Page 95 and 96:
Appendix A: Blade Server configurat
Page 97 and 98:
12Vdc HP StorageWorks 4/32B SAN Swi
Page 99 and 100:
Defining a Server Profile with FC C
Page 101 and 102:
7. Assign the profile to a server b
Page 103 and 104:
Appendix B: Blade Server configurat
Page 105 and 106:
12Vdc HP StorageWorks 4/32B SAN Swi
Page 107 and 108:
Defining a Server Profile with FCoE
Page 109 and 110:
8. The server can now be powered on
Page 111 and 112:
Appendix C: Brocade SAN switch NPIV
Page 113 and 114:
3. To be sure that the port is enab
Page 115 and 116:
Appendix D: Cisco MDS SAN switch NP
Page 117 and 118:
6. Click the FLOGI tab. In the Port
Page 119 and 120:
NPIV is enabled globally on the swi
Page 121 and 122:
2. Click npiv. 3. In the Action col
Page 123 and 124:
7. Click the FLOGI tab. In the Port
Page 125 and 126:
7. To verify that NPIV is properly
Page 127 and 128:
Appendix F: Static Login Distributi
Page 129 and 130:
4. Select Static Login Distribution
Page 131 and 132:
12. Click Name Server on the left s
Page 133 and 134:
Or on the first FlexFabric module (
Page 135 and 136:
2. In the same Interconnect Bay scr
Page 137 and 138:
2. Click Name Server on the left si
Page 139 and 140:
Testing the loss of uplink ports In
Page 141 and 142:
2. VC Uplink port X1 port status be
Page 143 and 144:
On the server side, the Boot from S
Page 145 and 146:
Figure 29: Emulex showing Boot from
Page 147 and 148:
Figure 32: Emulex showing Boot from
Page 149 and 150:
Acronyms and abbreviations Term BIO
Page 151 and 152:
Reference NPIV and Fibre Channel in
show all

Virtual Connect SAN Cookbook.pdf - Sallustio.ch

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?