Hitech Pro User Manual English - Tuncmatik

More documents

Recommendations

Info

BYPASS PHASE ROT. INVERTER STOP 4.35 DSP INTERN. ERROR 4.36 UPS STOP UPS STOPS LOW BATTERY UPS STOP 4.37 EMERGE. POWER OFF 4.38 NO OUTPUT VOLTAGE OUT SHORT-CIRCUIT BYP STOPS NO OUTPUT VOLTAGE 4.39 DSP INTERN. ERROR UPS BLOCK ALL 4.40 DC BUS VOLT WRONG 4.41 RECTIFIER BLOCK RECTIFIER BLOCKED BLK.UPS -> BLK.REC 4.42 RECTIFIER DESATS. RECTIFIER BLOCK 4.43 VOLTAGE RAMP ERR. RECTIFIER BLOCK RECTIFIER BLOCKS 4.44 INTERN.EXE. ERROR RECTIFIER BLOCK 4.45 DSP INTERN. ERROR RECTIFIER BLOCK 4.46 CONTACTOR T. FAIL RECTIFIER BLOCK 4.47 VOLTAGE RAMP ERR. 4.48 INVERTER BLOCK OUTPUT DC VOLTAGE INVERTER BLOCK 4.49 INVERTER BLOCKED BLK.UPS -> BLK.INV INVERTER BLOCKS 4.50 INVERTER DESATS. INVERTER BLOCK 4.51 INTERN.EXE. ERROR INVERTER BLOCK 4.52 LCD Messages Alarm Ref. DSP INTERN. ERROR INVERTER BLOCK INVERTER BLOCKS 4.53 UPS BLOCKED BLK.REC -> BLK.UPS UPS Blocked 4.54 INTERN.INI. ERROR 4.55
UPS BLOCK (DSP) INTERN.EXE. ERROR UPS BLOCK (DSP) UPS BLOCKED BLK.INV -> BLK.UPS INTERN.COM. ERROR UPS BLOCK (DSP) PARAL. SYS. DISC. UPS BLOCK UPS OVERTEMPERAT. UPS BLOCK RECTIFIER OVERLO. UPS BLOCK INVERTER DESATS. UPS BLOCK DSP INTERN. ERROR UPS BLOCK PFC & INV BLOCK. UPS BLOCK Table .6 Alarm list displayed in the LCD panel. 4.56 4.57 4.58 4.59 4.60 4.61 4.62 4.63 4.64 • Screen 4.16: The temperature of battery cabinet (in case of separate battery cabinet) or battery place (in case of battery are located inside the UPS) is higher than 40ºC. • Screen 4.17: If battery test (automatic or manual) is finished unsuccessfully, this alarm will appear. • Screen 4.18: Two possible reasons: During the unit start up, a message appears indicating that the battery switch can be switched ON. After some period of time without switching ON, this alarm appears When the unit is running under normal conditions, and the battery switch is switched OFF. • Screen 4.19: When the mains is connected during the start up, a phase rotation error is detected and the start up procedure is inhibited. • Screen 4.20: When the bypass is connected during the start up, a bypass phase rotation error is detected and the start up procedure is inhibited. • Screen 4.21: This alarm appears when in any phase, the rectifier input voltage phase to neutral is out of the set margins (+15%/–20% by default) or the rectifier input frequency is out of the set margins (± 0,5Hz by default). Then the rectifier is shut down. • Screen 4.22: This alarm appears when any IGBT in the rectifier side, desaturates the number of times programmed by display (50 by default). • Screen 4.23: This alarm appears when there is a (*) DSP Internal Error in the rectifier module, shutting down the rectifier immediately. There will be 3 more retries before the rectifier blocking. • Screen 4.24: When a mains phase rotation error is detected and under these conditions the
Page 1 and 2: HI-TECH PRO UNINTERRUPTIBLE POWER S
Page 3 and 4: 5-1-2. Start up procedure 5-2. COMP
Page 5 and 6: 1-2-2. For More Information & Help
Page 7 and 8: * Only in optional version UPS-B (S
Page 9 and 10: * Only in optional version UPS-B (S
Page 11 and 12: 3-1-2. Corresponding legends to the
Page 13 and 14: In equipments with separate bypass
Page 15 and 16: 4. INSTALLATION • As this is a de
Page 17 and 18: Maximum input and bypass current, n
Page 19 and 20: 4-2-4. Location • In the Instruct
Page 21 and 22: Single phase input / three phase ou
Page 23 and 24: for connecting the UPS with any mac
Page 25 and 26: 5-1-2. Start up procedure. It is ve
Page 27 and 28: are protected through the UPS 5-2.
Page 29 and 30: The UPS supplies output voltage ent
Page 31 and 32: 6-2-1. Messages menus and classific
Page 33 and 34: 6-3-3. ‘‘PARAMETERS’’ level
Page 35 and 36: • Screen 4.1: This alarm indicate
Page 37: END OF BATTERY LIFE ALARM BATT. TEM
Page 41 and 42: Positive DC bus voltage over 450V.
Page 43 and 44: hh: hour of deleted alarm mm: minut
Page 45 and 46: 7. ANNEXES 7-1. General Technical S

Hitech Pro User Manual English - Tuncmatik

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?