Product Overview 2010 - Lokshop

u
LokPilot Fx micro V3.0
LokPilot Fx micro V3.0 - Small and practical
LokPilot Fx micro V3.0
Motorless rolling stock can be digitalised with the LokPilot Fx
micro V3.0., for which the LokPilot Fx V3.0. is not small enough.
To this end, LokPilot Fx micro V3.0 offers four function outputs,
which can activate typical functions, such as car interior
illumination, head- or rear (-end, warning-) lights on cars, and
function models.
Of course, LokPilot Fx micro V3.0 is multi-protocol capable and
with a dimension of 13.5mm x 9.0 mm x 3.5 mm (0.54 x 0.36
x 0.12 inch) small enough for most any application. LokPilot Fx
micro V3.0 comes with an 6-wire NEM 651 harness.
Operational modes
LokPilot Fx micro V3.0 can handle DCC with 14, 28 or 128
speed steps as well as Motorola® and Selectrix®.
The decoder recognizes the speed steps automatically. It supports
Lenz® LG100 resp. ROCO® braking sections in addition
to Zimo®’s HLU-commands, or braking in DC sections with reversed
polarity as well as Märklin® braking sections (also for
DCC). You can either use short-, or four digit addresses, or assign
a consist address.
The Motorola® protocol enables the LokPilot Fx micro V3.0 decoder
to run with Märklin® stations 6020®, 6021®, delta®,
mobile station® and Central Station®. For those, the decoder
handles addresses 01 – 255, and comes to a halt correctly on
the Märklin® braking section. On Selectrix® layouts you can
choose between addresses 01 – 112.
LokPilot Fx micro V3.0 converses during operation fully automatically
between all control modes (Motorola®, DCC, DC, AC,
Selectrix®).
Analog operation
There are no restrictions for LokPilot Fx micro V3.0-equipped
rolling stock, of course, when operating in digital mode.
u
Technical data on page 54.
Functions
LokPilot Fx micro V3.0 comes with six function outputs, 140mA
each, and each can be assigned individually to a function: There
is flash light, alternate flash, (or ditch lights), strobe light, firebox
flicker as well as Mars-or Gyra light for US models. There
is also a high frequency-, time controlled output available for
digitally operated couplings.
All function outputs can be dimmed individually in 15 steps. In
DCC mode, each function output can be assigned to function
keys F0 - F12. F0 – F8 will be recognized in Motorola® mode,
the same in Selectrix® mode, depending on the station.
Programming
The LokPilot Fx micro V3.0 supports all DCC programming modes,
including POM (Programming on the main). For Märklin®
stations 6020®, 6021®, mobile station®, and Central Station®
all programming is also done electronically. For these units Lok-
Pilot Fx micro V3.0 employs a time proven, easily acquired programming
procedure.
The programmed changes during Motorola® operation are also
valid during DCC- and Selectrix® operation – and vice verse.
Programming parameters is especially simple for owners of our
ECoS command station: All options are displayed in plain language
on the large screen, and can easily be modified – even
during operation on the layout.
Interaction
LokPilot Fx micro V3.0 is designed for optimum interaction with
the LokSound V3.5 and the LokPilot V3.0 decoder: For example
it’s possible to equip the cab of an A-A consist with a LokSound
V3.5 decoder and the controlling car with a LokPilot Fx micro
V3.0 decoder. Given both the same address, they work absolutely
identically. Identical grouping of the CVs facilitates synchronisation
of both decoders.
RailCom®
RailCom® is activated ex works. You are able to read CVs on
the main track if you use an appropriate command station like
our ECoS.
Protection
All function outputs are protected against overload and short
circuit.
Built-in future
The LokPilot Fx micro V3.0 decoder is firmware upgradeable. New
software functions can be installed through the LokProgrammer.
Ordering information
52624 LokPilot Fx micro V3.0 functional decoder (MM/DCC/SX), with 6-pin plug according to NEM651 and
wire harness
53