2800/3350 Air Cart Manual - Amity Technology

More documents

Recommendations

Info

M ECHANICAL SYSTEMS - MAINTENANCE AND TROUBLESHOOTING Routine Maintenance Drive Line and Steering Lubricate all drive line bearings and steering components every 50 hours with a SAE multipurpose grease. Gear Box The gear box is fi lled at the factory and requires no maintenance. Service is required only if oil leaks become visible. Hydraulic Motor The hydraulic motor can only be damaged by heat or foreign material. Keep your tractor hydraulic oil and fi lter serviced regularly to ensure long life from your hydraulic components. Wheel Bearings Annually check wheel bearings for tightness. Adjust if needed. Repack every three (3) years. 28
Changing Metering Rolls - Ground Drive System To change metering rolls on a GD System: 1. Close the meter gate or ensure the bin is empty. 2. Remove the meter door and set aside. 3. Remove the chain from the meter drive sprocket. Do not remove the sprocket. 4. Remove the two nuts that hold the bearing on the meter shaft (sprocket end only). 5. Pull the shaft out of the meter while holding on to the meter roll. 6. Remove the meter roll. 7. Re-assemble the meter in reverse order with the desired fl ute. 3 4 29
Page 1: OWNERS OPERATING & PARTS MANUAL 280
Page 4 and 5: T ABLE OF CONTENTS Table of Content
Page 6 and 7: CONGRATULATIONS! Congratulations on
Page 8 and 9: M ECHANICAL SYSTEMS - SETUP AND OPE
Page 10 and 11: Using the Auger to Unload Products
Page 12 and 13: Tractor to Blower Hydraulic Coupler
Page 14 and 15: Setting Blower Speed The blower sho
Page 16 and 17: Blower Speed Sensor An inductive se
Page 18 and 19: Adjusting Product Meters The produc
Page 20 and 21: Variable Rate Drive Calibration and
Page 22 and 23: Entering Accumulated Weight on the
Page 24 and 25: Rate Charts 24
Page 26 and 27: Rate Charts 26
Page 30 and 31: Changing Metering Rolls - Variable
Page 32 and 33: Gear Box The gear box is fi lled wi
Page 34 and 35: Storage • Fully open the seed met
Page 36 and 37: AIR SYSTEM ASSEMBLY PARTS 36
Page 38 and 39: 27 28 24 23 29 25 26 22 30 18 19 20
Page 40 and 41: 10 11 9 13 12 14 15 4 2 1 8 7 3 6 5
Page 42 and 43: 9 4 3 2 5 6 8 2 1 8 9 2 8 5 8 7 ASS
Page 44 and 45: 44 41 40 42 39 16 48 12 13 11 19 18
Page 46 and 47: 9 2 8 1 2 1 4 5 7 10 3 6 12 13 11 A
Page 48 and 49: 4 9 17 8 3 8 9 14 16 18 9 19 1 6 12
Page 50 and 51: 1 2 ASSY-W&T 18.4X26 R1 8PLY, 16X26
Page 52 and 53: 16 9 24 15 16 10 17 6 12 16 29 16 1
Page 54 and 55: 15 27 28 26 10 13 13 12 25 24 16 23
Page 56 and 57: 9 2 1 24 22 6 23 13 8 6 14 16 21 20
Page 58 and 59: 22 18 19 22 TO AUGER 21 20 TO AUGER
Page 60 and 61: 6 10 9 8 14 13 2 1 4 5 3 12 3 7 11
Page 62 and 63: 21 27 18 3 10 21 27 19 18 22 22 15
Page 64 and 65: 9 7 12 10 8 6 11 13 8 4 5 3 1 2 ASS
Page 66 and 67: 4 9 10 2 3 2 1 7 8 5 6 ASSY-CATWALK
Page 68 and 69: 7 4 31 5 9 10 13 30 29 6 11 19 8 34
Page 70 and 71: 24 22 23 21 REF. 65816 WLDMT-AUGER
Page 72 and 73: 19 18 1 2 3 14 9 11 15 16 17 8 20 8

2800/3350 Air Cart Manual - Amity Technology

Create successful ePaper yourself

Delete template?

Save as template?