2800/3350 Air Cart Manual - Amity Technology

More documents

Recommendations

Info

Storage • Fully open the seed meters. • Open clean out doors on the bottom of the air tube. • Clean any remaining product from tanks. • Use water to thoroughly clean any compartment used for fertilizer • Thoroughly clean fertilizer and dirt from cup area. • Clean the inside of the seed meter door. Fertilizer, seed and dirt accumulate in this area. • Clean any remaining product from the auger and leave the auger slide open. • Oil chains. • Grease all lubrication points. • Check the gear box for visible leaks. If none, no service is required. • Release the latch on the tank lids to relieve pressure on the lid gaskets. 34
34814 CAB HARNESS INSTALLATION AND OPERATION 1. Mount the ISOBOX connector in a suitable location near your tractor hitch. 2. Route the generic tractor wiring harness from the hitch to the battery and the location where you will mount your virtual terminal. 3. At the rear of the tractor, remove the backshell cover on the ISOBOX connector. 4. Plug the bare contacts on the tractor harness into the back of the ISOBOX 4-pin connector using the table and connector diagram shown on the previous page as a reference. 5. Re-install the backshell cover on the ISOBOX connector. 6. Fit the CAN (2-pin) and ECU Power (4-pin) connectors on the tractor harness into the appropriate cutouts in the ISOBOX. 7. At the tractor battery, connect the red 16AWG and 8AWG power wires from the tractor harness to the positive terminal on the battery. 8. Connect the the 16AWG black/white and 8AWG black wires from the tractor harness to the negative terminal on the battery. 9. At the ISOBOX connector, use a meter or voltage test probe to verify that 12 volt power is present between terminals 3 & 1 and between terminals 4 & 2. Terminals 3 & 4 are power and terminals 1 & 2 are ground. The VT needs to be powered on to enable power between terminals 4 & 2. 10. Route the VT adaptor cable (P/N 34815) from the 6-pin VT connector on the tractor harness to the location in the tractor cab where you will mount the VT. 11. Plug the 6-pin VT connector on the tractor harness into the matching connector on the VT adaptor cable. Caution Double-check the pin locations before inserting each contact/wire. Removing the contats is possible but a special tool from Deutsch is required for each contact size. Caution Do not connect the D3030 VT to the wiring harness before verifying that the power connections are correct. 35
Page 1: OWNERS OPERATING & PARTS MANUAL 280
Page 4 and 5: T ABLE OF CONTENTS Table of Content
Page 6 and 7: CONGRATULATIONS! Congratulations on
Page 8 and 9: M ECHANICAL SYSTEMS - SETUP AND OPE
Page 10 and 11: Using the Auger to Unload Products
Page 12 and 13: Tractor to Blower Hydraulic Coupler
Page 14 and 15: Setting Blower Speed The blower sho
Page 16 and 17: Blower Speed Sensor An inductive se
Page 18 and 19: Adjusting Product Meters The produc
Page 20 and 21: Variable Rate Drive Calibration and
Page 22 and 23: Entering Accumulated Weight on the
Page 24 and 25: Rate Charts 24
Page 26 and 27: Rate Charts 26
Page 28 and 29: M ECHANICAL SYSTEMS - MAINTENANCE A
Page 30 and 31: Changing Metering Rolls - Variable
Page 32 and 33: Gear Box The gear box is fi lled wi
Page 36 and 37: AIR SYSTEM ASSEMBLY PARTS 36
Page 38 and 39: 27 28 24 23 29 25 26 22 30 18 19 20
Page 40 and 41: 10 11 9 13 12 14 15 4 2 1 8 7 3 6 5
Page 42 and 43: 9 4 3 2 5 6 8 2 1 8 9 2 8 5 8 7 ASS
Page 44 and 45: 44 41 40 42 39 16 48 12 13 11 19 18
Page 46 and 47: 9 2 8 1 2 1 4 5 7 10 3 6 12 13 11 A
Page 48 and 49: 4 9 17 8 3 8 9 14 16 18 9 19 1 6 12
Page 50 and 51: 1 2 ASSY-W&T 18.4X26 R1 8PLY, 16X26
Page 52 and 53: 16 9 24 15 16 10 17 6 12 16 29 16 1
Page 54 and 55: 15 27 28 26 10 13 13 12 25 24 16 23
Page 56 and 57: 9 2 1 24 22 6 23 13 8 6 14 16 21 20
Page 58 and 59: 22 18 19 22 TO AUGER 21 20 TO AUGER
Page 60 and 61: 6 10 9 8 14 13 2 1 4 5 3 12 3 7 11
Page 62 and 63: 21 27 18 3 10 21 27 19 18 22 22 15
Page 64 and 65: 9 7 12 10 8 6 11 13 8 4 5 3 1 2 ASS
Page 66 and 67: 4 9 10 2 3 2 1 7 8 5 6 ASSY-CATWALK
Page 68 and 69: 7 4 31 5 9 10 13 30 29 6 11 19 8 34
Page 70 and 71: 24 22 23 21 REF. 65816 WLDMT-AUGER
Page 72 and 73: 19 18 1 2 3 14 9 11 15 16 17 8 20 8

2800/3350 Air Cart Manual - Amity Technology

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?