CKD series HLC parallel grippers - BIBUS France

More documents

Recommendations

Info

Hand Series RRC GRC RV3* NHS HR LN FH100 HAP BSA2 BHA/ BHG LHA LHAG HKP HLA/ HLB HLAG/ HLBG HEP HCP HMF HMFB HFP HLC HGP FH500 HBL HDL HMD HJL BHE CKG CK CKA CKS CKF CKJ CKL2 CKL2 -*-HC CKH2 CKLB2 NCK/ SCK/FCK FJ FK Ending 1. COMMON CAUTION If a lateral load or load with a large impact is applied to the master key, play or damage could occur in the master key. Adjust and check that external force is not applied to the master key. The cylinder switch could malfunction if there is magnetic substance, such as a steel plate, near the cylinder switch. Keep magnetic substance at least 10mm from the cylinder. 10mm and over Magnetized device such as steel plate, etc. The cylinder switch could malfunction if cylinders are installed adjacently. Check that the following distances are provided between cylinders. 10mm and over 10mm and over If the clamp is operated carefully and slowly as possible, accuracy increases. Repeatability also stabilizes. Regularly grease the sliding section of the master key. Periodic replenishment of grease will extend the life of the part. Installing the jaw To prevent any effect onto the hand, support the master key with a wrench, etc., and tighten so that the master key is not twisted. Installation & Adjustment 10mm and over 10mm and over 2. Installation Do not cause dents or scratches that may worsen flatness or perpendicularity on the fixing face or master key. If there is a limit to the thickness direction of the FH series body, the available piping joint will be limited. Refer to the following joints. Fixing plate Hand Model Port size Joint Barbed joint Straight FTS Feather hand Joint Close piping port Open piping port FH*10 FH*12 M3 FH*16 FH*20 M5 FH*25 Applicable Effective Applicable O.D. Effective Model no. sectional area Model no. sectional area O.D. (mm) (mm 2 ) (mm) (mm 2 ) FTS4-M3 3.2· 4 0.4 FTS4-M5 3.2· 4 2.1 - - - FTS6-M5 6 Refer to the section below for details on installing the FH series. Top installation Front installation 4.1 Note) When a switch is provided, screw the bolt into as shown below so the switch is not pressed by the end of the bolt. 262 Check that no load is applied to the body. Tighten Side installation Note) Check that the fixed plate does not overlap the master jaw support. Model Applicable bolt size FH*10 M3 0.5 FH*12 M3 0.5 FH*16 M4 0.7 FH*20 M5 0.8 FH*25 M5 0.8 Max. screw depth (mm) 4.5 4.5 6 7.5 12 Recommended tightening torque (N·cm) 70 70 160 330 330
Use of throught hall Note) A throught hall cannot be used when a switch is provided. Note) Check that the fixed plate does not overlap the master jaw support. CAUTION Model Applicable bolt size FH*10 M3 0.5 FH*12 M2.5 0.45 FH*16 M3 0.5 FH*20 M4 0.7 FH*25 M4 0.7 Do not dissemble or modify the body. Recommended tightening torque (N·cm) 32 32 90 210 210 During Use & Maintenance When installing the small jaw, check that a lateral load is not applied to the master key. Lateral load Master key Tighten with the following tightening torque. Screw nominal Recommended tightening torque (N·m) M3 0.59 M4 1.4 Hand Series Precautions Small jaw M5 2.8 M6 4.8 M8 12.0 RRC GRC RV3* NHS HR LN FH100 HAP BSA2 BHA/ BHG LHA LHAG HKP HLA/ HLB HLAG/ HLBG HEP HCP HMF HMFB HFP HLC HGP FH500 HBL HDL HMD HJL BHE CKG CK CKA CKS CKF CKJ CKL2 CKL2 -*-HC CKH2 CKLB2 NCK/ SCK/FCK FJ FK Ending Hand 263
Page 1 and 2: RRC GRC RV3* NHS HR LN FH100 HAP BS
Page 3: When gripping a long object or larg
Page 7 and 8: How to order HLC 20CS L1 T2H R HLC
Page 9 and 10: Gripping power performance data Gri
Page 11: 0 0 Dimensions 63.5 37.5 26 HLC-25C

CKD series HLC parallel grippers - BIBUS France

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?