Owners Manual - Precor

More documents

Recommendations

Info

18 Operating and Maintaining the P10 Console Number Name Workouts Pause OK and Up/Down arrows Quick Start • Calories • Time Elapsed • Time Remaining • Watts (bike) • Time (bike) Incline or Crossramp Speed or Resistance • Average Speed (treadmill) • Speed (bike) • Pace (treadmill) • Distance (all equipment) • RPM (bike) • Cals/Min (AMT) • Strides/Min (AMT, EFX) • Total Strides (EFX) Details Examples of workouts: • <strong>Manual</strong> • Heart Rate • Interval • Weight Loss • Variety • Performance Use to pause or end a workout session. Use to navigate options and settings. Press Quick Start to begin exercising. Use the ▲ or ▼ arrows to change what information is displayed. Available on treadmill and EFX (dual). Available on AMT, bike, treadmill, EFX (single), and EFX (dual). Use the ▲ or ▼ arrows to change what information is displayed.
Chapter 2 Setting Up the Console Use the System mode to configure settings in ways that benefit your users and your facility. The System menu is visible only to administrators and registered service technicians. Changes made to these settings are saved to the fitness equipment. The System Settings categories are: • Club Parameters • Informational Display System Settings System Setting features remain hidden from club patrons and can only be accessed using special keypresses. To view the System Settings, the equipment must be in the Welcome state. The equipment is in the Welcome state when it is on, but not actually in use. This means that there is no exercise session, data entry, or diagnostic operation in progress. When the equipment is in the Welcome state: • SELECT A WORKOUT OR PRESS QUICKSTART TO BEGIN scrolls in the text display. • On the treadmill, the belt is not moving and the lift motor is off. Note: On self-powered equipment, the console initializes when you begin working out. You must maintain a minimum rate of motion for the Welcome banner to appear. The changes made in System Setting modes become the default settings when the display resets to the Welcome banner. CAUTION: If you change the Unit of Measure display on the treadmill, check the speed setting to verify that it is correct.
Page 1: Operating and Maintaining the P10 C
Page 5 and 6: Important Safety Instructions Impor
Page 7 and 8: Important Safety Instructions 5 •
Page 9 and 10: Important Safety Instructions 7 •
Page 11 and 12: Important Safety Instructions 9 Ind
Page 13 and 14: Important Safety Instructions 11 El
Page 15 and 16: Table of Contents Important Safety
Page 17 and 18: Chapter 1 Getting Started The P10 c
Page 19: Getting Started 17 Identifying Part
Page 23 and 24: Setting Up the Console 21 Select La
Page 25 and 26: Setting Up the Console 23 Remote Sp
Page 27 and 28: Setting Up the Console 25 Product V
Page 29 and 30: Setting Up the Console 27 Event Des
Page 31 and 32: Chapter 3 Introducing Users to the
Page 33 and 34: Introducing Users to the P10 Consol
Page 35 and 36: Introducing Users to the P10 Consol
Page 37 and 38: Chapter 4 Starting a Workout CAUTIO
Page 39 and 40: Starting a Workout 37 Pending Shutd
Page 41 and 42: Chapter 5 Maintenance To keep the e
Page 44 and 45: Precor Incorporated 20031 142nd Ave
Page 48 and 49: Edition Information ASSEMBLING AND
Page 50 and 51: 4 Assembling and Maintaining the EF
Page 56 and 57: 10 Assembling and Maintaining the E
Page 70 and 71:
24 Assembling and Maintaining the E
Page 72 and 73:
Page 74 and 75:
Page 76 and 77:
Page 78 and 79:
Page 80 and 81:
Page 82 and 83:
Page 84 and 85:
Page 86 and 87:
Page 88 and 89:
Page 90 and 91:
Page 92 and 93:
Page 94:
show all

Owners Manual - Precor

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?