CFR 2014/2015

The CFR Tunnel Racks are designed to go on the back of most snowmobiles
with a 141” or longer tunnel. They are made from strong yet lightweight
structural tubular aluminium. The CFR Tunnel Racks are
designed to carry extra fuel, backpacks, ski boots, etc. CFR also manufactures
a complete line of waterproof bags that are designed to fit seamlessly
with our racks, to keep your gear extra dry. If you need to carry
skis, snowboards, or pow surfers we offer a complete line of brackets that
bolt to the side of our racks to keep your gear secure and out of your way.
We are constantly working on making our product line up better every
year. The release of the new Mountain rack is as cutting edge as snowmobile
racks get.The overall height is a low profile 3 3/4". Dropping the
center of mass lowers all weight that is carried in the rack allowing the
snowmobile to perform better under load.
The CFR Mountain racks design also allows the rack to be mounted on
the edge of the tunnel. This will allow Ski Doo XM factory Holes to be
used to install the rack requiring no drilling into the rear tunnel. The new
design is also engineered to use fewer materials than existing racks yet
still be as strong.
2014/2015
Snowmobile Racks
and Accessories
Rider: Rob Alford
Photo: Geoff Kyle

Photo: Eric Berger
Skeet shooters: Eric Pehota and Dan Treadway

Index
Tunnel Racks
Mountain Rack.......................................................................Page 2
Irack.........................................................................................Page 3
Bracket Kits
Boardski Bracket Kit..............................................................Page 4
Snowboard Bracket Kit..........................................................Page 5
Single Ski Bracket...................................................................Page 6
Dual Ski Bracket.....................................................................Page 7
Powder Surf Bracket...............................................................Page 8
Bag Divison
Buck Bag..................................................................................Page 9
Dime Bag................................................................................Page 10
QP Bag....................................................................................Page 11
Direct Tunnel Mount
Boardski Rack System DTM...............................................Page 12
Metal Snowboard Rack System DTM................................Page 13
Metal Ski Rack System DTM...............................................Page 14
Snowmobile Control Divison
Boondocker.............................................................................Page15
Boondocker 2.0......................................................................Page16
Brett Turcotte Bar..................................................................Page 17
Dan Treadway Bar.................................................................Page 18
Dan Treadway 2.0 Bar...........................................................Page 19
Knucks Risers........................................................................Page 20
Accessories
Snowmobile Wraps...............................................................Page 21
Connect System.....................................................................Page 22
Blades......................................................................................Page 23
Spare Parts..............................................................................Page 24
Accessories.............................................................................Page 25

The CFR Tunnel Racks are designed to go on the back of most snowmobiles with a 141” or longer
tunnel. They are made from strong yet lightweight structural tubular aluminium. The CFR
Tunnel Racks are designed to carry extra fuel, backpacks, ski boots, etc. CFR also manufactures a
complete line of waterproof bags that are designed to fit seamlessly with our racks, to keep your
Extra gear dry. If you need to carry skis, snowboards, or pow surfers we offer a complete line of
brackets that bolt to the side of our racks to keep your equipment secure and out of your way.
Mountain Rack
Part# TR04
Tunnel Racks
Last years release of the Mountain rack was a huge success.
The response from the the low pro-file 3 3/4" height rack
weighing in at a featherweight 3.8 pounds was overwhelming.
Customers noticed that by dropping the center of mass, and
lowering all the weight that is carried in the rack, there
snowmobile performed better under load. The Mountain racks
design allowing Ski Doo XM factory Holes to be used to install
the rack was an added bonus as well. The abuse of rollovers and
bumpy access roads were no match for the strong yet
lightweight Mountain rack. A unanimous winner!
Features include:
-Made from extremely strong and lightweight 3/4”structural
tubular aluminum.
-Mounting Plates wrap around the sides of the rack for super
strength.
-Professional Welds for long lasting results.
-All mounting Hardware included is made from high grade
stainless steel. Super strong and rust Free
-Carries up to a 20L 6 G fuel container.
-Carries up to 2 pairs of Skis/Snowboards with proper attachments (Sold Separately)
-Mounts to most snowmobiles with a 141"
track or longer.
-Compatible with CFR Dime Bag and QP
Bag.
2
Specs
-Mounting plate lines up with Ski Doo XM
snowmobiles factory holes.
-Outside Rack dimensions
Height - 4 " Length - 13 1/2" Width - 17"
-Inside Rack dimensions
Length - 10 3/4" Width - 15 1/4"
-Mounting Plate dimensions
Length - 13 1/2" Width - 2 1/2"
Weight - 3.8 lbs
Photo - Mason Mashon

iRack
Part# TR03
The irack is celebrating its 5th year in our
products line up. The 4 3/4" overall height
weighing in at 4lb has proven itself year after year!
The CFR Connect system was designed around the
strong yet lightweight rack.
Features include:
- Available with CFR Connect system that allows irack to be put
on and taken off snowmobile without any tools. (Sold separately
and only available on ski doo XM and XP snowmobiles.)
-Made from extremely strong and lightweight 3/4”structural
tubular aluminum.
-Mounting Plates wrap around the sides of the rack for super
strength.
-Professional Welds for long lasting results.
-All mounting Hardware included is made from high grade
stainless steel. Super strong and rust Free-Carries up to a 20L 6 G
fuel container.
-Carries up to 2 pairs of Skis/Snowboards with proper attachments
(Sold Separately)
-Mounts to most snowmobiles with a 141" track or longer.
-Compatible with CFR Dime Bag and QP Bag.
Specs,
-Outside Rack dimensions
Height - 4 3/4" Length - 15 1/2" Width - 16 3/4"
Inside Rack dimensions
Length - 10 7/8" Width - 15 1/8"
-Mounting Plate dimensions
Length - 12 1/2" Width - 2 1/2"
Weight - 4 lbs
Photo: Russel Dalby
Rider: Dan Treadway
3

CFR Bracket Kits are designed to be attached to the CFR Mountain Rack, iRack, DD and D
racks. Each CFR Bracket is Designed to carry skis, snowboards, no boards, and powder surfers.
The Bracket Kits attach to the side of the CFR racks enabling up to two bracket kits to be
attached to each rack.
(Using the single ski brackets system only allows one bracket kit to be used)
Boardski bracket Kit
Part# K04
CFR Bracket Kits
The Boardski Bracket Kit can carry one snowboard
or one pair of skis and poles on the side of the DD,
iRack or Mountain Rack. It's the go to bracket for
people who both ski and snowboard or have friends
that ski and snowboard. Nothing has been
compromised in the design securing both skis or
snowboards.
4
Features:
-Carries one pair of skis/poles or
one snowboard.
-Light weight Nylon parts are infused
with resin that makes them extremely
strong and can handle -100 degree
cold temps.
-Custom made Injected moulded straps
that wont break in the cold but will break
in severe roll overs to prevent damage.
-Ratchets and Ladders are custom made for
superior ratcheting capabilities.
-All mounting Hardware included is made from
high grade stainless steel.
-Super strong and rust Free.
-Another Dual Ski bracket kit, Boardski bracket
kit, Pow surf bracket kit or snowboard bracket
kit can be used on other side of rack.
-Specifically designed to be fastened to CFR DD,
iRack or Mountain Rack. (Sold separately)
Photo: db
Snowmobiler: Johnny Foon

Snowboard bracket kit
Part# K01
The snowmobile Snowboard rack that is tested and approved by professional snowboarders
Travis Rice, Mark Carter, Mark Landvik, Helen Schettini and Annie Boulanger. The CFR
Snowboard Bracket Kit will keep your snowboard out of the way while snowmobiling. You will
forget that you have your snowboard with you breaking trail to the top of your favorite
snowboard line or jump spot. This package contains parts and hardware to carry one snowboard
on D, DD, i or Mountain Rack. Another Snowboard Bracket Kit can be purchased to carry up to
two Snowboards.
Features:
-Professionally used and approved by Snowboarders Travis Rice,
Mark Carter, Mark Landvik, Helen Schettini and Annie Boulanger.
-Light weight Nylon parts are infused with resin that makes
them extremely strong and can handle -100 degree cold temps.
-Injected molded straps that can withstand down to -100 degree cold temps but will break in
severe roll overs to prevent damage.
-Ratchets and Ladders are custom made for superior ratcheting lockdown.
-All mounting Hardware included is made from high grade stainless steel.
(Super strong and rust Free)
-Carries one snowboard. Another Snowboard Bracket Kit can be purchased to carry up to two
snowboards.
Photo: db
Shredder: Brian Hockenstien
5

Single ski bracket kit
Part# K03
The CFR single ski brackets system is designed to be mounted to D, DD, iRack or Mountain
Rack. This set up evenly distributes the weight of both skis and poles by carrying one ski and
pole on each side of rack. No other attachments are possible.
Features:
-Light weight Nylon parts are infused with resin that makes them extremely strong and can
handle -100 degree cold temps.
-Custom made Injected molded straps that wont break in the cold but will break in severe roll
overs to prevent damage
-Ratchets and Ladders are custom made for superior ratcheting capabilities
-All mounting Hardware included is made from high grade stainless steel.
-Super strong and rust Free
-Carries one ski and pole on each side of snowmobile. No other Brackets can be used with this
system.
-Specifically designed to be fastened to CFR D/DD/i or Mountain Rack
6
Photo - Blake Jorgenson
Skier - Dave Treadway

Dual Ski Bracket Kit
Part# K02
The CFR Dual Ski Bracket Kit will keep your skis and poles out of the way while
breaking trail to your favourite line or jump spot. This system can be used with another
dual ski bracket kit to carry up to two pairs of skis and poles.
It also can be used with a snowboard bracket kit to carry a snowboard on one side of snowmobile
and skis/poles on the other side of snowmobile. When two dual ski bracket kits are being used it
is putting a lot of extra weight on the
rear tunnel. Slow down going through rough conditions. Extra tunnel upports are a good idea if
you frequently travel in rough conditions with two pairs of skis.The Dual Ski Bracket kit is
specifically designed to be attached to the CFR DD, iRack or Mountain rack
Features:
-Professionally approved by Skiers Dan Treadway, Ian McIntosh, Dana Flahr,Seth Morrison and
Sage Cattabriga.
-Light weight Nylon parts are infused with resin that makes them extremely strong and can
handle -100 degree cold temps.
-Custom made Injected molded straps can handle -100 degree cold but will break in severe roll
overs to prevent damage.
-Ratchets and Ladders are custom made for superior ratcheting lock-down.
-All mounting Hardware included is made from high grade stainless steel. Super strong and rust
Free
-Carries one pair of skis and
poles. Another Dual Ski
bracket kit can be purchased
to carry up to two pairs of
skis
-Specifically designed to be
fastened to CFR DD, iRack
or Mountain Rack.
Photo - Blake Jorgenson
Sledskiers- Dave Treadway and friends!
7

Pow Surf Bracket Kit
Part# K05
The CFR Snowboard/Pow surf bracket is a result
of a direct collaboration with Jeremy Jensen at
Grassroots pows surfing and CFR. Jeremy needed a
rack on his snowmobile to carry his Pow surfers.
The Current CFR snowboard bracket kit he
had been using worked great for his snowboard
but didn't work with his pow surfers.
We hit the drawing board and designed a new bracket
that worked both to carry his revolutionary
binding-less snow riding Pow surfers and his regular
snowboard when he had to use bindings. If you want
to carry your Pow surfer or snowboard on your
snowmobile this is the bracket for you.
Features:
-Professionally used and approved by
Grassroots Founder Jeremy Jensen
-Light weight Nylon parts are infused with
resin that makes them extremely strong and
can handle -100 degree cold temps
-Injected molded straps that wont break in the
cold but will break in severe roll overs to
prevent damage
-Ratchets and Ladders are custom made for
superior ratcheting capabilities
-All mounting Hardware included is made from
high grade stainless steel.
-Super strong and rust Free
-Carries one snowboard or Pow Surf bracket
-Specifically designed to be fastened to CFR D,
DD, i and Mountain rack
8
Surfer- Jeremy Jenson
Photo- powsurf.com

The CFR Bag Division was developed to utilize certain key spots on the snowmobile
to carry much needed extra gear. Our goal was to only have the essentials
in your backpack and pockets. Lightening up your load when sledding and
shredding is a must have for high performance manoeuvres. The Bags are
waterproof and can withstand the hardest winter conditions you will face and
keep your gear dry and accessible.
Buck Bag
Bag Division
Part# B03
The new CFR handlebar bag conveniently attaches
between the handlebars of most snowmobiles.
The rip stop waterproof fabric along with waterproof
zippers keep you goods dry on the wettest days.
Using the CFR handlebar bag lets you empty your
jacket and pant pockets keeping all of your go to stuff
in one go to spot. With your jacket and pants pocket
empty you can boondock your snowmobile through
the trickiest terrain and side hill for miles.
9” of clearance is needed on XM snowmobiles between the top of the bag to the
DESS switch. If clearance is not available the bag can knock the DESS switch out
when turning sharply. Otherwise the Dess switch can be relocated if you still
want to rock the buck bag if you don’t have clearance.
Photo - db
9

Dime Bag
Part# B01
The CFR Dime Bag was designed by Pemberton, BC Canada based FYI designs. Tom Routh
head designer/snowboard legend/sled/moto head wanted a waterproof and super tough bag for
his CFR rack. The Dime Bag was the result. Tom chose leading fabric maker Dimension Polyent
for the outer shell because of its super tough and waterproof characteristics.
The CFR Dime Bag has Velcro
strips that wrap around the CFR
DD, i and Mountain racks tubular
bars in four spots to keep the bag
locked into place. The waterproof
zipper on the outside will keep
your contents dry. The inside
waterproof pocket is perfect for
your wallet and the key hook
keeps your keys in the right place.
A CFR scraper comes standard in all Dime
Bags so you can scrape the un wanted ice
build up on your snowboard/skis and running
boards. The CFR Dime Bag allows 10 cubic
inches of carrying capacity. Now you can bring
along your first aid kit, tow rope, siphon hoses,
beverages or whatever else you might need for
your winter adventures.
-Specifically designed to be
fastened to CFR D/DD/i
or Mountain Rack
10
Photo - db
Tandemers- db and Delaney

QP Bag
Part# B02
The CFR QP Bag offers 25 liters of waterproof carrying capacity and fits snugly
in all of the CFR rack systems. The QP is a telescoping bag that doubles in size
with a quick zipper extension to carry up to 50 liters of gear.
Features:
-Cordura waterproof fabric.
-Waterproof zippers.
-25 liter capacity. Un-zip the extension and up
to 50 liters of capacity are possible.
-Clips right into all CFR tunnel rack systems and
is easily removable.
-Shovel holder on the top enables a shovel to be
carried on the deep days for quick access.
-Convenient carrying handle.
-Individual inside pocket.
Photo: db
Tandamers: db and Jake Bauer
11

Direct Tunnel Mount
The CFR direct tunnel mount (DTM) rack systems are designed to be attached directly to the rear
tunnel of most snowmobiles. No other rack required.
Board-Ski Bracket System (DTM)
Part# M03
The ability to carry either a pair of skis and or a snowboards with no other rack required is now a
reality. Just buy this bracket, bolt it to your snowmobile, throw your skis and or snowboard on and
go. This is for the minimalist who doesn't want the rack on the back and just wants to carry his
skis and or snowboards depending on their fancy for the day.
Features:
-The CFR DTM Boardski bracket bolts to the side of
most snowmobiles. (Does not work on 2007 and newer
Polaris snowmobiles, 2012 and newer Arctic Cat
snowmobiles or 2003-2007 Ski-doo revs.
-Two Nylon infused polyurethane brackets carry
snowboard and or skis securely and safely.
-Custom made injection molded nylon straps keep
your gear tightly secured!
-CFR uses custom Ratchets designed to be used
under very high tensile loads with thicker springs
and ratcheting mechanisms.
-Carries either a pair of skis and poles or a snowboard.
-Another DTM Boardski bracket system can be
purchased to carry up to two
skis and or snowboards.
-Top vertical Holes line up with pre drilled Ski Doo
XM’s factory hole pattern.
Photo: Jussi Grznar
12

Metal Snowboard Rack System (DTM)
Part# M01
The snowboard rack tested and approved by snowboarders Eric Jackson, Bjorn Leines and Mads
Johnson. The Metal snowboard rack System is one of the lightest snowboard brackets on the
market weighing in at 2lbs. Tandem riding with your buddies is now easy as pie with your
snowboards on the rack and not in your back packs hitting you in the back of the head. Having
snowboards fastened to the snowmobile allows you to negotiate tricky snowmobiling situations
getting to your favorite big mountain line or jump spot.
The Metal Snowboard Rack system is made for
the minimalist who wants to be able to carry his
or her snowboard and nothing else. The CFR
Metal Snowboard Rack System carries one
snowboard on the side of your snowmobile.
(No other rack required)
Another Metal Snowboard Rack System can be
purchased to carry two snowboards. The CFR
Top mount Billet bracket (Sold separately) can
be purchased if you need to mount the bracket
to the top tunnel of your snowmobile.
Features:
-Used by Professional Snowboarders
Eric Jackson, Bjorn Leines and Mads Johnson
to get there snowboards into the backcountry.
-Metal Snowboard Rack System carries one
snowboard on the side of most snowmobiles
(No other rack required)
-Another snowboard can be carried by
purchasing another Metal Snowboard Rack
Systems.
-A cost effective way of carrying a snowboard on your snowmobile.
-Billet Aluminum top bracket is an optional part.
-Some snowmobile requires bracket to be mounted to the top of the rear tunnel.
-Light weight Nylon parts are infused with resin that makes them extremely strong and can
handle -100 degree cold temps.
-Custom made Injected molded straps that can handle temps as low as -100 cold but will break
in severe roll overs to prevent damage.
-Ratchets and Ladders are custom made
for superior ratcheting lock down.
-All mounting Hardware included is
made from high grade stainless steel.
(Super strong and rust Free)
13
Photo: Mason Mashon

Metal Ski Bracket System (DTM)
Part# M02
The CFR Metal Ski Bracket System is one of the lightest snowmobile ski racks available today at
5lbs. This is the minimalist set up for a person who only wants to carry one ski and pole on each
side of there snowmobile.
Having skis fastened to the snowmobile allows you to negotiate tricky snowmobiling situations
getting to your favorite backcountry recreating area.
Features:
-Metal Ski Bracket System carries one ski and
pole on each side of most snowmobiles.
(No other rack required.)
-A cost effective way of carrying a pair of skis
and poles on your snowmobile
-Light weight Nylon parts are made from
extremely strong infused resin that can
handle-100 degree cold temps
-Custom made Injected molded straps that will
not break in -100 degree cold but will break in
severe roll overs to prevent damage.
-Ratchets and Ladders are custom made for
superior ratcheting lock down
-All mounting Hardware included is made
from high grade stainless steel.
-Super strong and rust free
-Weight: 5 lb
Photo: Blake Jorgenson
Sledskiers: Mark Abma and friend.
14

Snowmobile Control Division
The CFR Boondocker handlebar, Dan Treadway handlebar and Knucks risers are now one of the
Industry leaders in aftermarket handlebars and risers for snowmobiles. Last year’s Boondocker
and Dan Treadway handlebar changed handlebar design and increased the performance of
snowmobiling. This year we added the Boondocker 2.0, Treadway 2.0 and Turcotte to our
handlebar line up. We added 1.5” of width on each bar to allow a more comfortable and stable
position when snowmobiling. The added width will also allow some stock controls to be attached
to the handlebars directly along with more brake lever space.
Our entire line up of handlebars are built
from the inside out. We start with high
quality 7075 double butted heat treated
aluminum for a strong and lightweight base.
In the center, where the risers stem clamps
to the bar, the width is a beefy 1 1/8” thick.
The handlebars then taper off to 7/8” thick
for all of your handlebar controls and hands
to fit nicely around. This construction also
allows energy to dissipate over a gradual
tapering thickness within the inner core.
This results in a stronger bar that dampens
hard hits and also gives the user a better feel
of what’s going on underneath on the snow.
Boondocker
Photo: Russell Dalby
Rider: Mark Sollors
Flat Black
Part# CD01
Monster Green Part# CD02
Specs
Ghost White
Part# CD03
-30” Width
-2” Rise, 7 Degree Up, 12 Degree Back 30 degree Back.
-Made from 7075 Heat treated super aluminum with Flex technology.
-Strong, Lightweight and tough as shit.
-Better positioning than stock bars and way stronger!
-Cutting edge design dissipates bumpy conditions better than stock bars keeping you fresh and
riding longer.
-Vertical and horizontal positioning graphics for the most accurate center and pull back angulation.
-CFR Bar pad included!
15

Boondocker 2.0
Flat Black
Part# CD01.5
Ghost White Part# CD03.5
Specs
Hot Pink
Part# CD12
-31.5” width
-2” Rise, 7 degree Up, 12 degree Back.
-Strong, Lightweight and tough as shit!
-The Bars bends and construction dissipate bumpy access roads and keep you less fatigued so
you ride better, and most importantly, longer.
-Vertical and horizontal positioning graphics allows for easy installation without needing a
tape measure!
-CFR Bar pad included.
16
Photo: Tim Grey

Brett Turcotte Signature bar
The Brett Turcotte signature bar is
the handlebar of choice for Brett
and his mind blowing snowmobiling
skills. From the Snowcross Track to
the backcountry, Brett is the Jedi
and this Handlebar his sword! Brett
Chose the Boondocker handlebar,
picked the color and designed the
graphics for this bar.
Available in Green Only!
Specs
Brett Turcotte Signature
Part# CD13
-31.5” width
-2” Rise, 7 degree Up, 12 degree Back.
-Strong, Lightweight and tough as shit!
-The Bars bends and construction dissipate bumpy access roads and keep you less fatigued so
you ride better, and most importantly, longer.
-vertical and horizontal positioning graphics allows for easy installation without needing a
tape measure!
-CFR Bar pad included.
Rider - Brett Turcotte
Photo - Julie-Ann Chapman
Rider - Brett Turcotte
Photo - Tim Grey
17

Dan Treadway Signature Bar
Dan changed what was thought
possible on a snowmobile. The Flat Black Part# CD04
only thing that was holding him
back was his equipment. This Bar
was the result of what Dan was
missing from his stock and other
aftermarket bars. The Bends were
Monster green Part# CD05
all Dans specs along with the
colors and graphics.
Specs
Ghost White Part# CD06
-30” width
-3” Rise, 8 degree Up, 14 degree Back
-Strong, Lightweight and tough as shit!
-The Bars bends and construction dissipate bumpy access roads and keep you less fatigued so
you ride better ,and most importantly, longer.
-Vertical and horizontal positioning graphics allows for easy installation without needing a
tape measure!
-CFR Bar pad included.
Photo: Russell Dalby
Snowmobiler: Dan Treadway
18
Photo: Bryn Hughes
Snowmobiler: Dan Treadway

Dan Treadway 2.0 Bar
Dan continues to push the sport of
snowmobiling in the mountains
year after year. His signature bar
reflects his all-around
snowmobiling just given er style!
Working with Dan’s Feedback last
year we decided to Release the
Treadway 2.0. The added 1.5”
width gives you stability on snow,
in the air, and gives you more
space on the handlebars for
controls and brake lever
positioning.
Specs
Flat Black Part# CD04.5
Monster green Part# CD05.5
Ghost White Part# CD06.5
-31.5” width
-3” Rise, 8 degree Up, 14 degree Back
-Strong, Lightweight and tough as shit!
-The Bars bends and construction dissipate bumpy access roads and keep you less fatigued so
you ride better, and most importantly, longer.
-Vertical and horizontal positioning graphics allows for easy installation without needing a
tape measure!
-CFR Bar pad included.
Photo: Russell Dalby
Snowmobiler: Dan Treadway
Photo: Bryn Hughes
Snowmobiler: Dan Treadway
19

Knucks Risers
Knucks Handlebar risers are ideal to personally customise
the height of your bars. Machined from Hi Strength super
tough 6061 - T06 Aluminum they can take anything you
can throw at them. An anodized black tumble finish and
Graphics kit will ad some style to your steed. The graphics
are not just for looks with a centering line on the top cap
allowing you to adjust your handle bars to where you want
them! The Knucks come in 4,5,6,7 and 8 inch heights and
will work on your 7/8" or over sized 1 1/8" bars.
Part#
4" CD07
5" CD08
6" CD09
7" CD10
8" CD11
Features:
-CNC machined from Hi strength 6061 - T06 Aluminum
-Graphics are laser etched for a durable long lasting look
-Anodized black and tumbled finished
-Available in 4,5,6,7 and 8" inch heights
-Will work with either 1-1/8" tapered bar or 7/8"bars.
Rider - Rob Alford
(Adaptor included.
-Patent pending ⅞" anti slip insert keeps bars where you want them
-You must have a pivot style steering post or a double pivot adapter
-Designed to be used with the new CFR Boondocker/DT Bars but will work with all
handlebars
-Double check length of cables and brake lines for a proper fit. Extended length cables
or brake lines may be required for proper operation
20

Wraps
New for 2014-2015 from CFR are sled wraps.
Sled wraps not only ad style to your whip but
also protect the plastic from the abusive sport
of snowmobiling. The graphics are a real hand
drawn topo graphical map of one of our
favorite snowmobiling areas just west of our
headquarters here in Pemberton BC Canada.
CFR is working with Toyskinz to produce
these wraps witch are made of industry
leading 6 mil. vinyl and 15 mil.over-laminate, making a total of 21 mil. thick. The Colors
and designs of the wraps work well with all of our other snowmobile accessories for a
tight look!
Ski-doo
Part#WSD01
White
Part#WSD02
Pink
Part#WSD03
Red
Part#WSD04
Black
Polaris
Part# WP01
Red
Part# WP02
White
Part# WP03
Pink
Part# WP04
Black
Arctic Cat
Part# AC01
Green
Part# AC03
Pink
Part# AC02
White
Part# AC04
Black
Yamaha
Part# WY01
Green
Part# WY03
Red
Part# WY02
Blue
Part# WY04
Black
21

Connect System
Part# C01
The CFR Connect System enables you to take your CFR
iRack on or off at whim! Four stainless steel buckles lock
your rack down to your snowmobile. Permanent Mounting
points on snowmobile are low profile stainless steel loops.
Go lightweight and low pro. Drop the rack and go.
*CFR Connect system only works with the CFR iRacks
and on Ski Doo XP/XM model snowmobiles with a 146"
tunnel or longer.
Photo: West Coast Sledders
Snowmobiler: Tom Cepek
22

Blades
Ad a little more Metal to your Ski Doo
XP/XM. The CFR Blades are designed to
be fastened to the outside or inside of the
rear tunnel of your 146”, 154", 163 or 174
tunnel. The added 50% more strength
allows more weight to be carried on the
tunnel. The CFR Blades are
recommended if you travel on bumpy
roads carrying lots of extra weight on
your snowmobile.
Features
- Anatomically designed to fit the rear tunnel of the Ski Doo XP/XM.
- Comes in 146”, 154” , 163”and 174" lengths.
- Mount them on the inside of your tunnel for the stock look.
- Mount them on the outside for the check me out I’m awesome look.
- Come complete with 1 right/1 left side.
- All Rivets and mounting hardware included.
Part# TS01 -146” Track length
Part# TS02 -154” Track length
Part# TS03 -163” Track length
Part# TS07 -174” Track length.
Nytro Blades square off the rear
rounded tunnel leaving a flat platform
to mount CFR tunnel racks.
Part# TS04 2010-2013 Yamaha Nytro.
Part# TS05 2008-2009 Yamaha Nytro.
06-08 Arctic Cat Blades go on dimples
that are on top of rear tunnel allowing
a flat surface for rack to sit on.
Part# TS06 2008-2009 Arctic Cat
Photo: Bryn Hughes
Tandemers: Dan Treadway
Logan Pehota
23

Aluminium Rachet
Part# 1006
The CFR Aluminum Ratchet is custom made to take the
abuse that snowmobiling throws at it.
These custom made ratchets are designed to hold your
snowboard and or skis down solid until you need them no matter what!. The powder
coated black finish will keep them rust free and looking good. The thick springs are long
lasting and will give you years of trouble free use.
-This Ratchet will replace all CFR ratchets current and past years.
Ladder Strap
Spare Parts
Part# 1003
The CFR 220MM Replacement Ladder Strap
works on all of our Snowboard and Ski Brackets.
-64 Stainless Steele rivet and two washers included.
Replacment Strap
Part# 1001
8" Replacement Strap
The CFR 8” replacement strap is used in most of the snowboard
and ski rack carrying racks that we manufacture. A 66 Stainless
steel rivet and two washers included.
Part# 1002
16" Replacement Strap
The CFR 16” replacement strap is used in all of the snowboard and ski rack carrying
racks that we manufacture. A 64 Stainless steel rivet and washer included.
24
Photo: Phil Tifo
Snowmobiler: Dan Treadway

Scraper
Part# 1012
The CFR Snow Scraper is a great way to scrape off
unwanted snow and ice from your running boards,
Snowboards or Skis.
In the shop you can scrape off the fresh hot wax from
your Skis or Snowboards.
Tunner Armour
Part# 1014
The CFR Tunnel armour use super sticky 3m adhesive to
add a layer of protection to your snowmobile. Stick the
pad on the tunnel to prevent against rubbing from
equipment.
Bar Pad
Part# CD12
The CFR bar pads are designed to fit all CFR
Handlebars or any oversized large diameter Handlebars.
The Dual density foam will protect against sharp
corners and hardware on riser. The Cordura material
with CFR logos is long lasting and can withstand cold
temps and all of the abuse that comes with
snowmobiling. The CFR Bar pad comes in Black with
white logos.
Super Straps
Part# 1013
The must have strap for your backcountry adventures,
the CFR Super Strap and duct tape can pretty much fix
anything.
Snow Scratchers
Part# S01
The CFR Snow Scratchers are a cost
effective way to prevent the
overheating of your snowmobiles
Motor on those early morning
long approaches.
Reversible Snow Scratchers
Accessories
Part# S02
These Scratchers are bad ass. They kick up twice as much snow as regular Scratchers and wont
break or bend if you accidentally go in reverse. Hanger
Included to secure scratchers when not in use.
25

For more info or
ordering please visit
cheetahfactoryracing.com
or call
(604)-894-1880
1-877-894-1880
Photo:db
2014/2015
Snowmobile Racks
and Accessories
Studio Photo:
Dice K.
Brian Hockenstein
Brochure:
Barrett Hepburn