Pet Immune PIR Motion Sensor 1 Introduction: Combined with multi ...
Pet Immune PIR Motion Sensor 1 Introduction: Combined with multi ...
Pet Immune PIR Motion Sensor 1 Introduction: Combined with multi ...
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
<strong>Pet</strong> <strong>Immune</strong> <strong>PIR</strong> <strong>Motion</strong> <strong>Sensor</strong> 1<br />
<strong>Introduction</strong>:<br />
<strong>Combined</strong> <strong>with</strong> <strong>multi</strong> innovative technology, here we have this hi-tech security detector. It consists of<br />
four parts, infra-red board, infra-red detector, advanced wireless emitting technology, and high quality<br />
nylon armor.<br />
Features:<br />
- Blurring logic processor, and intelligent analysis calculation method. It can define disruption signal<br />
and human activity signal. It can avoid wrong-report, and also resist strong electric magnetic,<br />
strong light, temperature fluctuation, hot air, pet disruption.<br />
- incorporated green technology which save electricity. The battery life can last for more than 2<br />
years.<br />
- automatically adjust to different room temperature.<br />
- The alarm automatically rings when the detector is opened.<br />
- There is reminding signal when the battery is low<br />
- The vibrating electric resistance can be set into three level which allows it to goes hand in hand<br />
<strong>with</strong> many different types of alarm machines and systems.<br />
- Equipped <strong>with</strong> long distance emitting system. In plain area, it can be effective up to 300 meters.<br />
- It uses number 5 battery which has higher electric capacity and longer battery life, so it can be<br />
replaced less oftenly.
<strong>Pet</strong> <strong>Immune</strong> <strong>PIR</strong> <strong>Motion</strong> <strong>Sensor</strong> 2<br />
Technical description:<br />
Main Control Board: imported wrong detection prevented and infra-red detecting board.<br />
Wrong detection eliminated: it resists strong electric magnetic, strong light, temperature fluctuation,<br />
hot air, and pet disruption.<br />
Processing mode:<br />
Testing mode: it goes into testing mode once it is started, and keeps ringing per six seconds. Until there<br />
have been no people <strong>with</strong>in the area for five minutes, it goes into the green mode or normal mode.<br />
Green mode: if there is no activity detected for five minutes, it will be <strong>with</strong>drawn from green mode.<br />
Afterward, it will be alarmed if it detects any activity.<br />
Normal mode: when the power-saving jumper is not inserted, there will be a lag time of six seconds<br />
between to alarm reports.<br />
Vibrating Electric Resistance:<br />
There are 3 available levels. 1.5M, 3.3M, or 4.7M.<br />
Emitting Distance:<br />
300 meter in a plain area.
<strong>Pet</strong> <strong>Immune</strong> <strong>PIR</strong> <strong>Motion</strong> <strong>Sensor</strong> 3<br />
Size:<br />
105x60x40mm<br />
Frequency:<br />
315 MHz. It could also be reset to other frequency.<br />
Jumper Installation Description:<br />
After changing the jumper setting, it need to be restarted. It takes 2 minutes to restart while there is no<br />
disruption allowed<br />
JP3 A0-A7 Jumper: jumper address<br />
JP2 A:1.5M/B3.3M Jumper: after inserting the jumper into the specific position, the value represents<br />
the frequency of the vibrating electric resistance; otherwise, the electric resistance is 4.7 when there is<br />
no jumper resisted.<br />
D0-D3 Jumper: the address of jumper’s data code.<br />
JP1 F Jumper: after installing it here, the detector can be effective in its largest range.<br />
M Jumper: after installing it here, the detector can detect its mid-range distance; this is the<br />
common position.<br />
N : no F or M installed. The detector can detect its closest range.<br />
I Jumper: after installing the jumper here, it goes into green mode. Under green mode, if the<br />
detector detected two activities <strong>with</strong>in five minutes, power-saving mode will be started. If there<br />
are activities detected <strong>with</strong>in another five minutes, it will not be alarmed, and the green mode<br />
will keep going for another five minutes. The same function will keep going if it keep detecting<br />
activities. However, if there are no activities detected for five minutes, it will be <strong>with</strong>drawn<br />
from green mode, and it will be alarmed once any activity is detected afterward.<br />
Installation Procedure:<br />
Step 1: open the detector
<strong>Pet</strong> <strong>Immune</strong> <strong>PIR</strong> <strong>Motion</strong> <strong>Sensor</strong> 4<br />
Step 2: according to the function, set the jumpers respectively. Install the battery, and plug the battery<br />
source wires onto the circuit board.<br />
Step 3: close the cover, and adjust the detecting angle.<br />
Signal:<br />
The light flashes 1 time: it initiate.<br />
When it flashes 2 times: the initiate mode finished.<br />
When it flashes 3 times: it detects activities and invasion. It is alarmed and send the alarm report.<br />
When it flashes 10 times: low on battery.<br />
Notice:<br />
- Only one detector can be installed <strong>with</strong>in the same area.<br />
- After replacing the battery or resetting the jumper, it takes two minutes to be initiated.<br />
- During the two minutes of initiate mode, no activities are allowed to disrupt it.<br />
Installation Position:<br />
- The most sensitive position is the frontal area of the detector.<br />
- Avoid direct sunlight.<br />
- Avoid high temperature, air conditioning and strong wind if possible.<br />
- Avoid putting unnecessary moving objects <strong>with</strong>in the area.<br />
- It should be installed on a solid wall or roof that there is no vibration.