LTI 20.20 Laser Speed Measurement Devices and ... - Tele-Traffic UK

More documents

Recommendations

Info

6. Highlighting the ‘YES’ option to download the data log To download the data log, highlight yes by pressing the ‘Up Option’, so that the following screen is displayed © Copyright – Tele-Traffic (UK) Limited 2007 ARE YOU SURE? � YES NO With ‘YES’ highlighted, press the ‘Enter Option’, and the data log will start to be downloaded. Whilst the data log is being downloaded the following message is displayed. DOWNLOADING LOG… EXIT UP DOWN LEFT RIGHT ENTER EXIT UP DOWN LEFT RIGHT ENTER 55
Once the data log has been downloaded the main menu screen is then displayed as shown below. Please note:- The above operation can only be used prior to setting the DVD recording system in operation. Whilst the system is in recording mode this operation is automatically controlled by on board computer programs and you will not be able to gain access. Viewing the DCU system status page © Copyright – Tele-Traffic (UK) Limited 2007 SET LIMIT OPTIONS SET USER NUMBER SET TIME/DATE SET CROSS-HAIR SET DISPLAY OPTIONS DATA LOG OPTIONS SYSTEM OPTIONS � EXIT To view the DCU system status page, follow the steps below. 1. Enter the DCU menu by pressing the symbol on screen. On entering the main menu, the following menu will be displayed. SET LIMIT OPTIONS SET USER NUMBER SET TIME/DATE SET CROSS-HAIR SET DISPLAY OPTIONS DATA LOG OPTIONS SYSTEM OPTIONS � EXIT EXIT UP DOWN LEFT RIGHT ENTER EXIT UP DOWN LEFT RIGHT ENTER 56
Page 1 and 2:
LTI 20.20 Laser Speed Measurement D
Page 3 and 4:
© Copyright - Tele-Traffic (UK) Li
Page 5 and 6: © Copyright - Tele-Traffic (UK) Li
Page 7 and 8: 12. TAPELOGGER Here there is a chan
Page 17 and 18: 2. Highlight the ‘SET LIMIT OPTIO
Page 19 and 20: 6. Adjusting the speed limit in the
Page 21 and 22: 4. Highlight the ‘SET SPEED TIMEO
Page 23 and 24: 2. Highlight the ‘SET USER NUMBER
Page 25 and 26: 2. Highlight the ‘SET TIME/DATE
Page 27 and 28: 2. Highlight the ‘SET CROSS-HAIR
Page 29 and 30: 6. Adjusting the cross-hair positio
Page 31 and 32: 4. Highlight the ‘SET TYPE’ sel
Page 35 and 36: 2. Highlight the ‘SET CROSS-HAIR
Page 37 and 38: 6. Adjusting the cross-hair size in
Page 39 and 40: 4. Highlight the ‘SET GAP’ sele
Page 41 and 42: 2. Highlight the ‘SET DISPLAY OPT
Page 43 and 44: 6. Adjusting the display position i
Page 45 and 46: 4. Highlight the ‘SET BACKGROUND
Page 47 and 48: 2. Highlight the ‘DATA LOG OPTION
Page 49 and 50: 6. Navigating the data log in the
Page 51 and 52: 4. Highlight the ‘CLEAR DATA LOG
Page 53 and 54: Once the data log has been cleared
Page 55: 4. Highlight the ‘DOWNLOAD DATA L
Page 59 and 60: 4. Highlight the ‘DCU STATUS’ s
Page 63 and 64: 1. Entering the DVD Menu by pressin
Page 65 and 66: The Exit Option will always take th
Page 67 and 68: If the disk is BLANK the following
Page 69 and 70: If the correct disk has been loaded
Page 71 and 72: 6. Event marker. The Event marker s
Page 73 and 74: The Operator now has two choices:-
Page 75 and 76: Once the DVD disk is removed and th
Page 77 and 78: AGAIN select the EXIT Option and th
Page 79 and 80: Now select the REC Option and the f
show all

LTI 20.20 Laser Speed Measurement Devices and ... - Tele-Traffic UK

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?