ericsson review - ericssonhistory.com
ericsson review - ericssonhistory.com
ericsson review - ericssonhistory.com
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
Technical data<br />
Capacity<br />
Number of extensions 40 100<br />
Trunk lines incl. junction<br />
lines 12 24<br />
Local junctors 5 10<br />
Tone senders 3 6<br />
Operators 1 1<br />
Dimensioned for 0.17 erlangs with a congestion<br />
of 0.01 and 20-40% internal traffic.<br />
Cabinet Height Width Depth<br />
mm mm mm<br />
40 extensions 1068 600 300<br />
100 extensions 1800 600 300<br />
Telephone sets with dial for 10 or 16 Hz and<br />
the pulse ratio 30/70-50/<br />
50;<br />
with push-button set for<br />
tone frequency key sending<br />
in accordance with CCITT<br />
Current feeding 2\400 ohms<br />
Loop resistance max. 1800 ohms for extension<br />
lines, including the<br />
telephone set, max. 1000<br />
ohms for exchange lines<br />
Leakage resistance min. 40 kohms<br />
Attenuation 0.8 dB on exter- 1<br />
nal circuits<br />
7 dB on internal<br />
circuits<br />
at8Q0Hz<br />
Crosstalk attenuation min. 80 dB at 1100 Hz<br />
Numbering two or three-digit extension<br />
numbers<br />
Power feeding 110/127/220/230/240 V a.c,<br />
50/60 Hz or 42- 54 V da,<br />
max. power consumption<br />
250 W<br />
Environment +5° to +40°C ambient temperature<br />
20-80 % relative humidity<br />
connected to the exchange, i.e. telephone<br />
sets and the operator's console<br />
Thus, for example, data concerning test<br />
connections can be programmed from a<br />
push-button telephone and most of the<br />
administrative data for the exchange,<br />
such as classes of service and<br />
abbreviated numbers, can be programmed<br />
from the operator's console.<br />
It is thus always possible to administer<br />
the exchange and carry out simple fault<br />
localization without having to introduce<br />
extra equipment. However, it is possible<br />
to connect an I/O device of standard<br />
type to the exchange when large<br />
quantities of data have to be fed in, for<br />
example when the exchange is put into<br />
operation or when advanced test and<br />
fault localization programs are run. For<br />
this purpose the exchange is equipped<br />
with a terminal outlet with a standardized<br />
interface in accordance with<br />
CCITT V24. A portable typewriter terminal<br />
is normally connected, but a display<br />
terminal can be used instead. Remote<br />
<strong>com</strong>munication via modems is also possible.<br />
Normally the I/O function is not permanently<br />
connected, but is introduced in<br />
the system when required by inserting<br />
the necessary memory and interface<br />
boards.<br />
The I/O device can be used for:<br />
— programming of system data<br />
— initiation of test programs<br />
— printout of the results of test programs<br />
— printout of devices with disturbance<br />
marking<br />
19<br />
— printout of busy, blocked or test<br />
marked devices<br />
- printout of traffic recording data.<br />
Fault localization<br />
Fault localization in ASB 100 can be carried<br />
out either by means of test connections<br />
or program-controlled tests.<br />
Test connections are programmed from<br />
a normal push-button telephone or from<br />
the I/O device.<br />
Program controlled tests are carried out<br />
from the I/O device with the aid of special<br />
test programs. The boards with<br />
these can either be permanantly connected<br />
in the exchange or plugged in<br />
when required. They permit quick<br />
localization of faults down to the printed<br />
board assembly level.<br />
The tests can be carried out without disturbing<br />
the normal operation of the exchange.<br />
Command language<br />
Aspecial <strong>com</strong>mand language is used for<br />
<strong>com</strong>munication with ASB 100 from the<br />
typewriter terminal. A <strong>com</strong>mand consists<br />
of a <strong>com</strong>mand word and in certain<br />
cases a parameter part where the<br />
parameters are separated by colons.<br />
The <strong>com</strong>mand word consists of a<br />
mnemonic <strong>com</strong>bination of five letters,<br />
where the two first letters define the<br />
function, the next two define the subgroup<br />
within this function and the last<br />
letter defines the order that is to be carried<br />
out.