4G INSTALLATION GUIDE - Morpho

More documents

Recommendations

Info

Install Hardware After all devices are configured and connected to the RS-485 network, the baud rate can be increased to the highest supported rate (some experimentation might be required). 4.7 SINGLE-DOOR CONTROLLER INSTALLATION The 4G Lite devices incorporate an internal relay that enables them to operate a deadbolt/door strike directly. WARNING The internal relay is limited to a maximum current of 1A. If the deadbolt/ doorstrike to be controlled draws more than 1A, damage to the device may occur. If the deadbolt/door strike load exceeds 1A, an external relay must be used, as described below. Do not use the same power supply to power a 4G Lite device and a door strike. Assuming the current drawn by the deadbolt/door strike is less than 1A, the connections between 4G Lite device, deadbolt/door strike, and power supply for the deadbolt/door strike should be made. Note that a snubber diode (1N4007 or equivalent) must be connected across the deadbolt/door strike to protect the DC power supply from inductive kickback. CAUTION The snubber diode and DC power supply for the deadbolt/door strike are not supplied with the 4G Lite device. The power supply should be specified in accordance with the voltage and current requirements of the deadbolt/door strike, but it must be ensured that the current to operate the dead bolt/door strike does not exceed 1A. If the current required to operate the deadbolt/door strike exceeds 1A, an external relay must be used in conjunction with the 4G Lite device. The external relay must be specified so that its contacts are rated to carry the current required by the deadbolt/door strike, and that the current required to operate its energizing coil is within the 1A capacity of the 4G Lite device's internal relay. Part # 430-4G-050-00-006 © 2011 - L-1 Identity Solutions Inc. All rights reserved
Install Hardware Figure 4-12 Connections for Internal Relay Operation The power supply for the external relay must be chosen to match the operating voltage and current of the external relay coil, but its voltage must not exceed the 4G Lite device's internal relay maximum voltage rating of 250 volts. The external relay should be connected. Note that snubber diodes (1N2007 or equivalent) should be connected across the external relay coil and the deadbolt/door strike. Figure 4-13 Connections for External Relay Operation Part # 430-4G-050-00-006 © 2011 - L-1 Identity Solutions Inc. All rights reserved
Page 1 and 2:
4G INSTALLATION GUIDE Version 4.4.5
Page 3 and 4:
Contents Table of Contents CHAPTER
Page 5 and 6:
Contents 8.1.1 ERROR 1406 - INSUFFI
Page 7 and 8: Introduction CHAPTER 1 - INTRODUCTI
Page 9 and 10: Introduction 1.2 PRODUCT OVERVIEW 1
Page 11 and 12: Introduction 1.3 DEVICE DIMENSIONS
Page 13 and 14: Introduction 1.3.3 4G V-STATION LIT
Page 15 and 16: Introduction 1.4 SAFETY PRECAUTIONS
Page 17 and 18: Planning the Installation CHAPTER 2
Page 19 and 20: Planning the Installation 2.1.2 REQ
Page 21 and 22: Planning the Installation SQL Serv
Page 23 and 24: Planning the Installation 2.1.4 CHO
Page 25 and 26: Planning the Installation To avoid
Page 27 and 28: Planning the Installation transmiss
Page 29 and 30: Planning the Installation with acci
Page 31 and 32: Install Software 3. Click 4G LiteRe
Page 33 and 34: Install Software Figure 3-4 SecureA
Page 35 and 36: Install Software Figure 3-6 SecureA
Page 37 and 38: Install Software Figure 3-8 Connect
Page 39 and 40: Install Software Figure 3-10 Secure
Page 41 and 42: Install Software Figure 3-13 Welcom
Page 43 and 44: Install Software Figure 3-15 Secure
Page 45 and 46: Install Software Figure 3-17 Instal
Page 47 and 48: Install Hardware CHAPTER 4 - INSTAL
Page 49 and 50: Install Hardware Figure 4-2 4G V-Fl
Page 51 and 52: Install Hardware Figure 4-4 4G Secu
Page 53 and 54: Install Hardware Figure 4-6 Connect
Page 55 and 56: Install Hardware Table 4-1 PoE Pin
Page 57: Install Hardware Figure 4-11 4G Lit
Page 61 and 62: Install Hardware Figure 4-14 Locati
Page 63 and 64: System Start-Up Procedures CHAPTER
Page 65 and 66: Configure Device CHAPTER 6 - CONFIG
Page 67 and 68: Configure Device Figure 6-2 Registe
Page 69 and 70: Configure Device 8. Select a Group.
Page 71 and 72: Configure Device NOTICE The first t
Page 73 and 74: Configure Device 11.Enter a Device
Page 75 and 76: Maintenance and Cleaning 3. Rub the
Page 77 and 78: Troubleshooting Log off and log on
Page 79 and 80: Troubleshooting 8.1.4 ERROR 27502 -
Page 81 and 82: Troubleshooting 8.1.6 INSUFFICIENT
Page 83 and 84: Notices CHAPTER 9 - NOTICES CHAPTER
Page 85 and 86: Notices Under Industry Canada regul
Page 87 and 88: Glossary and Acronyms Optical Senso
show all

4G INSTALLATION GUIDE - Morpho

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?