ipc-a-610 âacceptability of electronic assembliesâ - SMTA

More documents

Recommendations

Info

NEW FORMAT 6 Terminals ♦ 6.1 Terminals - Edge Clip 4.7 ♦ 6.2 Swaged Hardware 4.3 ♦ 6.2.1 Swaged Hardware - Flared Flange 4.3 ♦ 6.2.1.1 Swaged Hardware - Flared Flange - Controlled Split 4.3.1.1 ♦ 6.2.2 Swaged Hardware - Terminals 4.3.3 ♦ 6.2.3 Swaged Hardware - Flat Flange - Fused-in-Place 4.3.2, 6.6.6 ♦ 6.3 Wire/Lead Preparation, Tinning 4.3.2 ♦ 6.4 Terminals - Lead Forming - Stress Relief 5.3.2.3 ♦ 6.5 Terminals - Service Loop 5.5.4 ♦ 6.6 Terminals - Stress Relief Lead/Wire Bend 5.5.3 ♦ 6.7 Terminals – Lead/Wire Placement 5.5.5, 5.5.1 ♦ 6.7.1 Terminals – Lead/Wire Placement - Turrets and Straight Pins 5.5.1
NEW FORMAT CONT. ♦ 6.10 Terminals – Solder 6.6 ♦ 6.10.1 Terminals – Solder - Turrets 6.6.2 ♦ 6.10.2 Terminals – Solder – Bifurcated 6.6.1 ♦ 6.10.3 Terminals – Solder - Slotted Terminal Assembly Requirements ♦ 6.10.4 Terminals – Solder - Pierced/ Perforated 6.6.4 ♦ 6.10.5 Terminals – Solder - Hook/Pin 6.6.3 ♦ 6.10.6 Terminals – Solder - Solder Cups 6.6.5
Page 1 and 2: IPC-A-610 “ACCEPTABILITY OF ELECT
Page 3 and 4: TRAINING PROGRAM CERTIFIED IPC TRAI
Page 5: SECTIONS RE-NUMBER ♦ Section 1 -
Page 9 and 10: SECTION 6 - TERMINALS CONT. ♦ Cri
Page 11 and 12: NEW SECTION ♦ 5 Soldering ♦ 5.1
Page 13 and 14: WHAT TO EXPECT ♦ TABLES LIKE J-ST
Page 15 and 16: WHAT TO EXPECT CONT. ♦ Example of
Page 17 and 18: WHAT TO EXPECT CONT. ♦ Section 5
Page 19 and 20: ADDITIONAL CRITERIA ♦ PQFN ♦ BG
Page 21 and 22: BGA CRITERIA CONT. ♦ 8.2.12.5 Pla
Page 23 and 24: PLASTIC QUAD FLAT PACK - NO LEADS (
Page 25 and 26: D-PAK Section 8.2.14 CONT. Target -
Page 27 and 28: SECTION 9 - COMPONENT DAMAGE (New S
Page 29 and 30: 9.5 CONNECTORS CONT. Defect - Class
Page 31: IPC-A-610 REVISION “D” WORKSHOP

ipc-a-610 âacceptability of electronic assembliesâ - SMTA

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?

ipc-a-610 âacceptability of electronic assembliesâ - SMTA