W1683 Manual - Grizzly Industrial Inc.

More documents

Recommendations

Info

SAFETY FIRST! SAFETY READ MANUAL BEFORE OPERATING MACHINE FAILURE TO FOLLOW INSTRUCTIONS BELOW WILL RESULT IN PERSONAL INJURY Indicates an imminently hazardous situation which, if not avoided, WILL result in death or serious injury. Indicates a potentially hazardous situation which, if not avoided, COULD result in death or serious injury. Indicates a potentially hazardous situation which, if not avoided, MAY result in minor or moderate injury. It may also be used to alert against unsafe practices. NOTICE This symbol is used to alert the user to useful information about proper operation of the equipment. 1. Thoroughly read the instruction manual before operating your machine. Learn the applications, limitations and potential hazards of this machine. Keep manual in a safe, convenient place for future reference. 2. Keep work area clean and well lighted. Clutter and inadequate lighting invite potential hazards. 3. Ground all tools. If a machine is equipped with a three-prong plug, it must be plugged into a threehole electrical outlet or grounded extension cord. If using an adapter to aid in accommodating a twohole receptacle, ground using a screw to a known ground. 4. Wear eye protection at all times. Use safety glasses with side shields or safety goggles (that meet the national safety standards) while operating this machine. 5. Avoid dangerous environments. Do not operate this machine in wet or open flame environments. Airborne dust particles could cause an explosion and severe fire hazard. 6. Ensure all guards are securely in place and in working condition. 7. Make sure switch is in the “OFF” position before connecting power to machine. 8. Keep work area clean and free of clutter, grease, etc. 9. Keep children and visitors away. All visitors should be kept a safe distance away while operating unit. 10. Childproof workshop with padlocks, master switches or by removing switch keys. 11. Disconnect machine when cleaning, adjusting or servicing. 12. Do not force tool. The machine will do a safer and better job at the rate for which it was designed. 4
13. Use correct tool. Do not force machine or attachment to do a job for which it was not designed. 14. Wear proper apparel. Do not wear loose clothing, neck ties, gloves, jewelry, etc. 15. Remove adjusting keys and wrenches before turning the machine on. Make this a habit! 16. Use proper extension cord. When using an extension cord, make sure it is in good condition. Use extension cords 100' or less in length that are rated Hard Service (grade S) or better, and that have a conductor size of 16 A.W.G. A drop in line voltage, loss of power and overheating can result when using an undersized cord. The extension cord must have a ground wire and ground plug pin, as well. 17. Keep proper footing and balance at all times. SAFETY 18. Do not leave machine unattended—wait until it comes to a complete stop before leaving the area. 19. Perform machine maintenance and care. Follow lubrication and accessory attachment instructions in the manual. 20. Keep machine away from open flame. Operating machines near pilot lights and/or open flames creates a high risk if dust is dispersed in the area. Dust particles and an ignition source may cause an explosion. Do not operate the machine in high risk areas, including but not limited to, those mentioned above. 21. Do not use machine under the influence of drugs or alcohol or if you are excessively tired. 22. Do not let untrained people use the machine if they are not supervised by an experienced operator. 23. If at any time you are experiencing difficulties performing the intended operation, stop using the machine! Then contact our service department or ask a qualified expert how the operation should be performed. 24. Mag switches can be accidentally turned on when they are bumped. Always be aware of the mag switch location when moving items around the shop. Operating this equipment has the potential for flying debris to cause eye injury. Always wear safety glasses or goggles when operating equipment. Everyday glasses or reading glasses only have impact resistant lenses, they are not safety glasses. Be certain the safety glasses you wear meet the appropriate standards of the American National Standards Institute (ANSI). 5
Page 1 and 2: MODEL W1683 20" PLANER INSTRUCTION
Page 3 and 4: Table Of Contents PAGE 1. INTRODUCT
Page 5: WARRANTY AND RETURNS Woodstock Inte
Page 9 and 10: ELECTRICAL REQUIREMENTS NOTICE NEVE
Page 11 and 12: Shop Preparation • Floor Load: Yo
Page 13 and 14: Handwheel Figure 4. Handwheel attac
Page 15 and 16: ADJUSTMENTS Do not connect power to
Page 17 and 18: 3. Place the block on one end of th
Page 19 and 20: Checking Knives The Model W1683 fea
Page 21 and 22: To tighten the knives after adjustm
Page 23 and 24: 7. Lower the chipbreaker and the pr
Page 25 and 26: The power should not be connected t
Page 27 and 28: Always wear safety glasses when ope
Page 29 and 30: Troubleshooting Planing Results Pla
Page 31 and 32: MAINTENANCE Disconnect power to the
Page 33 and 34: Belt Tension Frequently inspect the
Page 35 and 36: TROUBLESHOOTING This section covers
Page 37 and 38: 35 36 37 38 21 44 25 43 1 96 2 97
Page 39 and 40: 206 211 212 207 6201TR SPACE-AGE BE
Page 41 and 42: 414 415 413 419 406 405 406 407 404
Page 43 and 44: 41 C C D D B B A A 532 531 529 530
Page 45 and 46: WARRANTY CARD Name_________________

W1683 Manual - Grizzly Industrial Inc.

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?