Develop a time stamping application in PlantStruxure? - Schneider ...

More documents

Recommendations

Info

3-Design Figure 4 System architecture for “time stamped by module” • Time stamped by program There are two ways to implement the method of time stamped by program. Here we use the example of NTP mode. The solution is designed based on the M340 system. The clock reference is provided by the NTP server, and the signal data is time stamped by a CPU program. As showed in Fig 6, the system includes the following parts: • M340 system (BMX P34 2020) with I/O module, • NTP client module (BMX NOE 0100) • GPS (Global Positioning System) receiver, including NTP server unit 22
3-Design The GPS receiver with NTP server provides the time signal to each client by Ethernet. The CPU obtains the time information through the NTP client module in M340 system. Time stamps with 5-10 ms resolution can be achieved by NTP mode. GPS Receiver Human Machine Interface(HMI) NTP Server Ethernet TCP/IP NTP synchronizing Ethernet Switch M340 PLC BMX XBP 0600 CPS CPU NOE DDI_1 CPS2000 DC24V P34 2020 Modbus, Ethernet NOE 0100.2 DDI 1602 Signal source Figure 5 System architecture for “time stamped by program” (NTP mode) 3.2. System software design The software used in this STG are based on SoCollaborative, which is a part of PlantStruxure. Three SoCollaborative software components are needed in the design of the time stamping function: • Vijeo Citect • OFC Factory Server • Unity Pro In the Process Operator’s Station: Vijeo Citect Run Time is used to display the time stamping value. OPC Factory Server is used to connect to the PAC system. 23
Page 1: How can I … Develop a time stampi
Page 4 and 5: The STG Collection System Technical
Page 6 and 7: 6. Operation.......................
Page 8 and 9: 1-Introduction 8
Page 10 and 11: 1-Introduction Figure 1 Time stampi
Page 12 and 13: 1-Introduction 1.3. Challenges Figu
Page 14 and 15: 2-Selection 14
Page 16 and 17: 2-Selection Figure 3 Time stamping
Page 18 and 19: 2-Selection Table 3 Solution list f
Page 20 and 21: 3-Design 20
Page 24 and 25: 3-Design In the Process Engineering
Page 26 and 27: 3-Design Figure 7 shows the program
Page 28 and 29: 3-Design The table below gives para
Page 30 and 31: 3-Design The next table gives param
Page 32 and 33: 3-Design The following table gives
Page 38 and 39: 3-Design For example, the TimeStamp
Page 40 and 41: 3-Design 40
Page 42 and 43: 4-Configuration • PAC configurati
Page 44 and 45: 4-Configuration 4.2. Time stamped b
Page 46 and 47: 4-Configuration • SCADA This proc
Page 48 and 49: 5-Implementation NTP mode: Use the
Page 50 and 51: 5-Implementation 5.2. SCADA There a
Page 52 and 53: 5-Implementation 52
Page 54 and 55: 6-Operation 6.2 Time stamping alarm
Page 56 and 57: 7- HPP Example The hydro power cont
Page 58 and 59: 7- HPP Example SCADA can be used to
Page 60 and 61: 7- HPP Example Use this section to
Page 62 and 63: 7- HPP Example The turbine and gene
Page 64 and 65: 7- HPP Example Figure 18 Device Lis
Page 66: Schneider Electric Industries SAS H

Develop a time stamping application in PlantStruxure? - Schneider ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?