HR01 Appliance-Loft Mechanical Ventilation with Heat Recovery ...
HR01 Appliance-Loft Mechanical Ventilation with Heat Recovery ...
HR01 Appliance-Loft Mechanical Ventilation with Heat Recovery ...
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
Installation and Maintenance<br />
5.0 Data cable installation<br />
A 4-core data cable is used to connect devices. Do not run<br />
data cable in the same conduit as the mains cables and<br />
ensure there is a 50mm separation between the data cable<br />
and other cables. The maximum cable run between any two<br />
devices is 300m when it is installed in accordance <strong>with</strong> the<br />
instructions. Please note that the total data cable length used<br />
in any system must be less than 1000m. Keep the number of<br />
cable joints to a minimum to ensure the best data transmission<br />
efficiency between devices.<br />
6.0 Adjusting the <strong>HR01</strong>-PIR run on<br />
timer (1-60 minutes)<br />
Assuming the sensor(s) are installed, adjustment of the set<br />
points achieved by tilting the sensor forwards which exposes<br />
the adjustment aperture (see fig 5). Using a small screwdriver,<br />
gently turn the dial either clockwise or anti-clockwise to<br />
increase or decrease the set point. When adjustments are<br />
made to the sensor, the LED light on the sensor front will flash<br />
on and off to show the set point. First, green flashes will<br />
indicate the set point in TENS, then red flashes will indicate<br />
UNITS. For example one green flash and five red flashes show<br />
you that the PIR timer is set to fifteen minutes.<br />
7.0 Detection range<br />
Up to 10m directly in front of lens and up to 2m at 40 o to the<br />
lens axis.<br />
<strong>HR01</strong>-PIR Sensor<br />
8.0 Maintenance<br />
The unit does not require any maintenance. However, for<br />
optimum performance, it is advisable to remove any<br />
accumulated dust <strong>with</strong> a low power vacuum cleaner.<br />
NOTE: Installation and Maintenance of the equipment must<br />
be as directed in the instructions provided <strong>with</strong> the unit.<br />
9.0 Warranty<br />
Standard warranty starts from the day of purchase or delivery.<br />
Polypipe extend the warranty from one to three years on<br />
receipt of the warranty card attached and proof of delivery/<br />
purchase, providing this is returned <strong>with</strong>in the first year.<br />
The warranty covers all parts proven to be faulty at point of<br />
manufacture but excludes problems arising from incorrect<br />
installation. In this instance, if a Polypipe engineer is required<br />
to attend site the call out will be chargeable.<br />
This warranty is conditional upon evidence of planned<br />
maintenance and does not extend to consumable items.<br />
Damaged appliances must not be installed but returned to<br />
point of purchase.<br />
10.0 Service Enquiries<br />
Polypipe can assist you in all aspects of service. Our service<br />
department will be happy to provide any assistance required,<br />
initially by telephone and If necessary arrange for an engineer<br />
to call.<br />
11.0 Warranty Card <strong>HR01</strong>-PIR Sensor<br />
*Name:<br />
*Address:<br />
*Postcode:<br />
*Telephone:<br />
Email:<br />
*Model:<br />
*Serial No:<br />
Installer:<br />
Installer Address:<br />
*Date Installed:<br />
*Date Purchased:<br />
Retailer:<br />
Retailer Location:<br />
May we send you relevant product information and remind you when service is due<br />
Your details will not be disclosed to any third party.<br />
*Data required:<br />
Return <strong>with</strong> proof of delivery/purchase to:<br />
Polypipe <strong>Ventilation</strong><br />
Sandall Stones Road, Kirk Sandall Industrial Estate,<br />
Kirk Sandall, Doncaster, DN3 1QR<br />
Tel: +44 (0)8443 715 523 Fax: +44 (0)8443 715 524<br />
Technical or commercial considerations may, from time to time,<br />
make it necessary to alter the design, performance<br />
and dimensions of equipment and the right is reserved to make<br />
such changes <strong>with</strong>out prior notice.<br />
Leaflet Number 671450 February 2010