33 11 00 Water Distribution.pdf - WPC

More documents

Recommendations

Info

AWWA C111/A21.11 AWWA C115/A21.15 AWWA C151/A21.51 AWWA C153/A21.53 AWWA C203 AWWA C500 AWWA C502 AWWA C504 AWWA C508 AWWA C509 AWWA C600 AWWA C605 AWWA C651 AWWA C700 (2000) Rubber-Gasket Joints for Ductile-Iron Pressure Pipe and Fittings (2005) Flanged Ductile-Iron Pipe With Ductile-Iron or Gray-Iron Threaded Flanges (2002; Errata 2002) Ductile-Iron Pipe, Centrifugally Cast, for Water (2006) Ductile-Iron Compact Fittings for Water Service (2002) Coal-Tar Protective Coatings and Linings for Steel Water Pipelines - Enamel and Tape - Hot-Applied (2002; R 2003) Metal-Seated Gate Valves for Water Supply Service (2005) Dry-Barrel Fire Hydrants (2006) Standard for Rubber-Seated Butterfly Valves (2001) Swing-Check Valves for Waterworks Service, 2 In. (50 mm) Through 24 In. (600 mm) NPS (2001) Resilient-Seated Gate Valves for Water Supply Service (2005) Installation of Ductile-Iron Water Mains and Their Appurtenances (2005) Underground Installation of Polyvinyl Chloride (PVC) Pressure Pipe and Fittings for Water (2005; Errata 2005) Standard for Disinfecting Water Mains (2002; R 2003) Standard for Cold Water Meters - Displacement Type, Bronze Main Case AWWA C701 (2007) Standard for Cold-Water Meters - Turbine Type for Customer Service AWWA C702 AWWA C703 AWWA C704 AWWA C707 (2001) Cold-Water Meters - Compound Type (1996; R 2004) Cold-Water Meters - Fire Service Type (2002) Propeller-Type Meters for Waterworks Applications (2005) Encoder-Type Remote-Registration Systems for Cold-Water Meters SECTION 33 11 00 Page 6
AWWA C800 AWWA C900 AWWA C901 AWWA C906 AWWA M23 (2005) Underground Service Line Valves and Fittings (2007) Polyvinyl Chloride (PVC) Pressure Pipe, and Fabricated Fittings, 4 In. Through 12 In. (100 mm Through 300 mm), for Water Distribution (2002) Polyethylene (PE) Pressure Pipe and Tubing, 1/2 In. (13mm) Through 3 In. (76 mm), for Water Service (2007) Polyethylene (PE) Pressure Pipe and Fittings, 4 In. (100 mm) through 63 In., (1,575 mm) for Water Distribution and Transmission (2002) Manual: PVC Pipe - Design and Installation ASME INTERNATIONAL (ASME) ASME B16.1 ASME B16.15 ASME B16.18 ASME B16.22 ASME B16.26 ASME B18.2.2 ASME B18.5.2.1M ASME B18.5.2.2M (2005) Standard for Gray Iron Threaded Fittings; Classes 125 and 250 (2006) Cast Bronze Threaded Fittings Classes 125 and 250 (2001; R 2005) Cast Copper Alloy Solder Joint Pressure Fittings (2001; R 2005) Standard for Wrought Copper and Copper Alloy Solder Joint Pressure Fittings (2006) Standard for Cast Copper Alloy Fittings for Flared Copper Tubes (1987; R 2005) Standard for Square and Hex Nuts (2006) Metric Round Head Short Square Neck Bolts (1982; R 2005) Metric Round Head Square Neck Bolts ASTM INTERNATIONAL (ASTM) ASTM A 307 ASTM A 47/A 47M (2007b) Standard Specification for Carbon Steel Bolts and Studs, 60 000 PSI Tensile Strength (1999; R 2004) Standard Specification for Steel Sheet, Aluminum-Coated, by the Hot-Dip Process SECTION 33 11 00 Page 7
Page 1 and 2: JBLM DESIGN STANDARDS SECTION 33 11
Page 3 and 4: 5,000 90,000 5,500 85,000 6,000 80,
Page 5: the WSCMP for review instead of ind
Page 9 and 10: ASTM D 2468 ASTM D 2564 ASTM D 2657
Page 11 and 12: Water service line piping, fittings
Page 13 and 14: Handle Polyvinyl Chloride (PVC), pi
Page 15 and 16: gates and mechanical-joint ends or
Page 17 and 18: (2) Class A - Rated capacity of 100
Page 19 and 20: seat; two follower rings; two resil
Page 21 and 22: e connected and shall be either the
Page 23 and 24: fasteners. The main casing shall be
Page 25 and 26: water piping; adequate structural s
Page 27 and 28: setscrewed flanges to make flanged
Page 29 and 30: Install PVCO Pressure piping in acc
Page 31: specified in this section. The Cont

33 11 00 Water Distribution.pdf - WPC

Create successful ePaper yourself

Delete template?

Save as template?