SASH LOCK - Truth Hardware

More documents

Recommendations

Info

700 SERIES LOCKS FIG. 6 C C30705 CHECK RAIL RAIL LOCK LOCK KEEPER KEEPER 2.062 [52.4 mm] 2.812 [71.4 mm] .156 [4.0 mm] .375 [9.5 mm] .365 [9.3 mm] .312 [7.9 mm] AVAILABLE LOCKS A30700400 A30700401 A30700400 A30700401 A30700400 A30700401 A .903 [22.9mm] .653 [16.6mm] .903 [22.9mm] .653 [16.6mm] .903 [22.9mm] .653 [16.6mm] B .060 [1.5mm] RECOMMENDED SCREWS: (QTY 2) #6 SCREW WITH A #5 HEAD, PHILLIPS FLAT HEAD SHEET METAL SCREW. (LENGTH AND THREAD TYPE TO BE DETERMINED BY PROFILE.) FIG. 7 C C30706 CHECK RAIL LOCK KEEPER 2.062 [52.4 mm] 2.812 [71.4 mm] .141 [3.6 mm] .375 [9.5 mm] AVAILABLE LOCKS A30700400 A30700401 A30700400 A30700401 A30700400 A30700401 A .888 [22.5mm] .638 [16.2mm] .888 [22.5mm] .638 [16.2mm] .888 [22.5mm] .638 [16.2mm] RECOMMENDED SCREWS: B .060 [1.5mm] .365 [9.3 mm] .280 [7.1 mm] (QTY 2) #6 SCREW WITH A #5 HEAD, PHILLIPS FLAT HEAD SHEET METAL SCREW. (LENGTH AND THREAD TYPE TO BE DETERMINED BY PROFILE.) FIG. 88 C C30715 CHECK RAIL RAIL LOCK LOCK KEEPER KEEPER 2.062 [52.4 mm] 2.700 [68.6 mm] .156 [4.0 mm] .319 [8.1 mm] AVAILABLE LOCKS A30700400 A30700401 A30700400 A30700401 A .903 [22.9mm] .653 [16.6mm] .873 [22.1mm] .623 [15.8mm] RECOMMENDED SCREWS: B .060 [1.5mm] .030 [.7mm] .505 [12.8 mm] FIG. 9 C C30716 CHECK RAIL RAIL LOCK LOCK KEEPER KEEPER 2.062 [52.4 mm] 2.700 [68.6 mm] .135 [3.4 mm] .319 [8.1 mm] .505 [12.8 mm] .312 [7.9 mm] .270 [6.9 mm] (QTY 2) #6 PHILLIPS FLAT HEAD SHEET METAL SCREW. (LENGTH AND THREAD TYPE TO BE DETERMINED BY PROFILE.) AVAILABLE LOCKS A30700400 A30700401 A30700402 A30700403 A .882 [22.4mm] .632 [16.1mm] .852 [22.6mm] .602 [15.2mm] RECOMMENDED SCREWS: (QTY 2) #6 SCREW WITH A #5 HEAD, PHILLIPS FLAT HEAD SHEET METAL SCREW. (LENGTH AND THREAD TYPE TO BE DETERMINED BY PROFILE.) B .060 [1.5mm] .030 [.7mm] 1c 700 west bridge street, owatonna, mn 55060 ■ 507.451.5620 800.866.7884 ■ TRUTH.COM
DOUBLE HUNG SLIDER 9200 SASH LOCK & KEEPERS 3 The options available on Truth Hardware’s 9200 Series Sash Locks are virtually endless. • There are bases with or without alignment lugs which are helpful in preventing side shift of the sash (See Truth Tip #1). • There are various mounting hole patterns from which to choose, which will ensure that your hardware is located in the most efficient location for optimum holding power (See Truth Tip #5). • A variety of locking cams are available that help to pull meeting rails tightly together and will produce a better seal of the sash at the head and sill to help decrease air infiltration. Another reason for optional cam sizes is to help avoid potential interference created when the cam extends out to far. Refer to the following drawings to find the one which best meets your requirements. • Based on window design, and the space allowed for mounting the window hardware – some window systems are better suited for narrower keepers, or even facemounted varieties. The 9200 Series has a number of Top Mount, and Face Mount keepers to choose from. LOGO OPTIONS: For that “personalized touch”, Truth’s 9200 Series Check Rail Locks are capable of accepting your company’s name or logo. Truth’s logo reproduction process is an attractive way of highlighting your company signature. For further details on where your company’s logo would appear, please refer to the following drawings. WARRANTY: Protected under the terms of the “Truth Warranty for Window & Door Manufacturers & Authorized Distributors”. Refer to Truth’s Terms & Conditions for further details. MATERIAL: High-pressure, corrosion-resistant, die-cast zinc. FINISH: Electrostatically applied, durable coatings that provide excellent resistance to chipping, scratching and corrosion while maintaining color stability for years in direct sunlight. Please refer to Truth’s Color Chart for examples of Truth’s most popular finish options. Truth also offers a wide range of decorative “plated” finishes – contact Truth for additional information on availability of these finishes on specific product lines. ORDERING INFORMATION: 1. Choose the 9200 Series Cam Lock style desired (specify by part number). 2. Specify finish number. 3. Specify Keeper to be ordered. RECOMMENDED SCREWS: Types of screws required determined by material of profile used (sold separately). For additional information on screw selection - see Truth Tips. TRUTH TIPS: 1. A lock with pick-resistant alignment nibs should be used whenever possible. A lock without nibs should be chosen when the lugs cause interference with divided light grills or other window features. 2. A lock with a small cam should be used when the larger sweep radius of the .125” (3.2 mm) pull-in cam causes interference with the glazing or other areas of the profile. A face-mounted keeper is usually required. 3. When two locks are used on one window, the placement of each lock, with respect to its keeper, becomes very critical to maintain a constant weatherseal on all sides of the window and to insure that each lock engages properly with its keeper. 4. For accurate hardware placement in vinyl or metal applications, pre-drilling of the window profile is recommended. 5. For vinyl window applications, mounting screws should pass through two PVC walls, or one PVC wall and one insert wall. For this reason, it may be necessary to use a longer screw than is recommended. 6. For metal window profiles, Truth recommends stainless steel machine screws. However, in most applications, stainless steel sheet metal screws will provide adequate holding power. INCLUDE TRUTH SPECS ON YOUR NEXT WINDOW PROJECT Window check rail locks shall be included which will increase both security and weather seal tightness. The lock must provide easy operation and positive locked feel. Window check rail locks will be of internal cam design to provide optimum pull-in to aid in sealing the meeting rails. The lock and accompanying keeper will prevent misalignment during locking. The lock and keeper shall be constructed of high pressure zinc alloy die castings. Window locks shall be 9200 Series locks as manufactured by Truth Hardware.
Page 1 and 2: Connecting Innovations In Hardware
Page 3 and 4: Sliding Window Hardware Catalog TAB
Page 5 and 6: DOUBLE HUNG SLIDER 700 SERIES LOCKS
Page 7: 700 SERIES LOCKS FIG. FIG. 3 3 700
Page 11 and 12: 9200 SASH LOCK & KEEPERS 3b FIG. 2
Page 13 and 14: 9200 SASH LOCK & KEEPERS 3d FIG. 5
Page 15 and 16: 9200 SASH LOCK & KEEPERS 3f FIG. 9
Page 17 and 18: 9200 SASH LOCK & KEEPERS 3h FIG. 13
Page 19 and 20: 9200 SASH LOCK & KEEPERS 3j FIG. 17
Page 21 and 22: DOUBLE HUNG SLIDER 17 TRIMLINE CAM
Page 23 and 24: DOUBLE HUNG SLIDER 17 TRIMLINE CAM
Page 25 and 26: 17 TRIMLINE CAM LOCK KEEPERS FIG. 4
Page 27 and 28: DOUBLE HUNG SLIDER 9400 SASH LOCK &
Page 29 and 30: 9400 SASH LOCK & KEEPERS 6b FIG. 3
Page 31 and 32: DOUBLE HUNG SLIDER 17 ENTRYGARD® I
Page 33 and 34: DOUBLE HUNG SLIDER 17 ENTRYGARD® C
Page 35 and 36: 17 ENTRYGARD® CAM LOCK KEEPERS FIG
Page 37 and 38: DOUBLE HUNG SLIDER 17.04 SASH LOCK
Page 39 and 40: FIG. 3 C09417 KEEPER FIG. 4 41807 K
Page 41 and 42: DOUBLE HUNG SLIDER 9900 SASH LOCK 1
Page 43 and 44: 9900 SASH LOCK 10b
Page 45 and 46: DOUBLE HUNG SLIDER 9950 LOCK WITH C
Page 47 and 48: DOUBLEHUNG SLIDER 30590 CAM GARD
Page 49 and 50: DOUBLE HUNG SLIDER 17 RESTORATION H
Page 51 and 52: DOUBLE HUNG SLIDER 19 POSITIVE ACTI
Page 53 and 54: 19 POSITIVE ACTION LOCK (PAL SYSTEM
Page 59 and 60:
DOUBLE HUNG SLIDER 19 FuSION SYSTEM
Page 61 and 62:
19 FuSION SYSTEM 15b F FIG. 1 FUSIO
Page 63 and 64:
19 FuSION SYSTEM 15d FIG. 4 FUSION
Page 65 and 66:
19 FuSION SYSTEM 15f FIG. 6 FUSION
Page 67 and 68:
FIG. 9 FUSION KEEPER ASSEMBLY (FOR
Page 69 and 70:
19 FuSION SYSTEM 15j FIG. 11 FUSION
Page 71 and 72:
DOUBLE HUNG SLIDER 19 HARMONY SYSTE
Page 73 and 74:
19 HARMONY SYSTEM 15.1b FIG. 1 19.7
Page 75 and 76:
19 HARMONY SYSTEM 15.1d FIG. 5 19.7
Page 77 and 78:
19 HARMONY SYSTEM 15.1f FIG. 7 19.7
Page 79 and 80:
19 HARMONY SYSTEM 15.1h FIG. 12 456
Page 81 and 82:
19 HARMONY SYSTEM 15.1j FIG. 14 19.
Page 83 and 84:
19 HARMONY SYSTEM 15.1l FIG. 17 456
Page 85 and 86:
DOUBLE HUNG SLIDER TILT LATcHES Tru
Page 87 and 88:
FIG. 2 46.21.XX.001 TILT LATCH LEFT
Page 89 and 90:
TILT LATcHES FIG. 5 1038L TILT LATC
Page 91 and 92:
TILT LATcHES FIG. 9 46.13 TILT LATC
Page 93 and 94:
DOUBLE HUNG SLIDER SASH LIFTS Truth
Page 95 and 96:
18.10 SASH LIFTS 17b FIG. 3 18.16 S
Page 97 and 98:
DOUBLE HUNG SLIDER WINDOW ROLLERS T
Page 99 and 100:
DOUBLEHUNG SLIDER PIVOT BARS Trut
Page 101 and 102:
DOUBLEHUNG SLIDER MISCELLANEOUS T
show all

SASH LOCK - Truth Hardware

Create successful ePaper yourself

Delete template?

Save as template?