Tailift Sales Manual - Worldwide Forklifts

More documents

Recommendations

Info

Right angle stack calculations (normal load) Aisle width; use narrowest aisle in which truck must right angle stack products. See illustration on page 39 and formula below Truck specs and load solve for this number from formula A-1 or A-2 below Clearance (see chart below) Measured aisle mm + mm = or less than mm in + in in Right angle stack formulas (normal load) Right angle stack Formula A-1 When D is less than C + 2R Aisle width = Z + A + B + operator clearance Required aisle width for truck specs + load = Z_______ + A ________ + B_________ =________ Insert above CAUTION The pivot point of a three wheel truck is found between the drive wheels and not outside the turning wheel as it is with a four wheel truck. Therefore, when calculating right angle stack for a three wheel truck, use these formulas. When Z is greater than D Then aisle width = Z + Y 2 When Z is smaller than D Then aisle width = D + Y 2 2 Y = (A + B) 2 + D 2 2 Mathematical calculation of right angle stacking aisle Right angle stack Formula A-2 When D is greater than C + 2R, but less than 2Z – C – 2R Aisle width = Z + Y + operator clearance, then solve for Y Y = D - C - R 2 + (A + B) 2 2 2 Note: * Y cannot exceed Z * If Y is longer than Z, use wide load calculation (page 40) Required aisle width for truck specs + load =__________ Z_________+ Y _________ = _________ Insert above Clearance Chart Suggested minimum aisle /operator clearance chart 12192 mm / 40 ft long load - Add 1220 mm or 48 inches 9144 mm / 30 ft long load - Add 914 mm or 36 inches 6096 mm / 20 ft long load - Add 610 mm or 24 inches 3048 mm / 10 ft long load - Add 305 mm or 12 inches 1524 mm / 5 ft long load - Add 152 mm or 6 inches 1219 mm / 4 ft long load - Add 102 mm or 4 inches 51 Tailift Sales Manual 2005
Right angle stack illustration (normal load) A = Distance from center of drive wheel to face of fork B = The length of the load (always in line with the truck) C = The maximum width of the truck D = The width of the load (across the truck) R = Inner turning radius Y = Load Radius Z = Truck Radius 52 Tailift Sales Manual 2005
Page 1 and 2: INDEX Glossary 1-3 Explanation of f
Page 3 and 4: Indicated horsepower: The horse pow
Page 5 and 6: Explanation of forklift terms Load
Page 7 and 8: Turning radius The radius of the lo
Page 9 and 10: These angles are essential for asse
Page 11 and 12: Weight Truck weight: Total weight o
Page 13 and 14: 12 Tailift Sales Manual 2005
Page 15 and 16: Lift Truck Class I-VII Class I - El
Page 17 and 18: TAILIFT IC CUSHION MAST SPECIFICATI
Page 19 and 20: TAILIFT IC CUSHION MAST SPECIFICATI
Page 21 and 22: TAILIFT IC PNEUMATIC MAST SPECIFICA
Page 23 and 24: TAILIFT IC PNEUMATIC MAST SPECIFICA
Page 25 and 26: TAILIFT LPG AND DIESEL TRUCK WEIGHT
Page 27 and 28: TAILIFT LPG AND DIESEL TRUCK WEIGHT
Page 29 and 30: DUAL PNEUMATIC TIRES MODEL SIZE P.R
Page 31 and 32: English to Metric Conversion Factor
Page 33 and 34: DECIMAL EQUIVALENTS OF FRACTIONS 1/
Page 35 and 36: Grade in degrees and percent Degree
Page 37 and 38: Part 1 1. Maximum weight lifted kg
Page 39 and 40: 4. Product Data 4a. Type of Product
Page 41 and 42: 5. Towing consideration (if applica
Page 43 and 44: 8. Ventilation conditions Consider
Page 45 and 46: 11. Boxcar loading or unloading (if
Page 47 and 48: 13. Overhead Obstructions Maximum o
Page 49 and 50: 16. Ramp data (if not applicable, g
Page 51: Part 2 Bulk Storage Calculations Ai
Page 55 and 56: Right angle stack illustration (wid
Page 57 and 58: Intersecting aisle illustration A =
Page 59 and 60: Summary Sheet 1.- Maximum weight li
Page 61 and 62: 6. PAYMENTS: Customer agrees to pay
Page 63 and 64: Circle one answer from each questio
Page 65 and 66: A. Visibility is improved. B. The t
Page 67 and 68: Check at the beginning of each 8 ho
Page 69: Engineering and Standards Informati

Tailift Sales Manual - Worldwide Forklifts

Create successful ePaper yourself

Delete template?

Save as template?