Tailift Sales Manual - Worldwide Forklifts

More documents

Recommendations

Info

Head clearance The head clearance from the under face of overhead guard to the upper face of seat when the operator [90 kg (199lbs)] is seated. Counterweight height The height from the ground to the top of the counterweight. Backrest height The height from upper of the forks to the top of backrest. Maximum fork spread The distance of outer forks when the forks are moved on the outsider notches of carriage. Minimum fork spread The distance of outer forks when the forks are move on the inside notches of carriage. Maximum ground clearance The height from the ground at the position where the clearance from the ground is considered minimum, except the elevating portion of the loading device and around the wheels. C 1 : C 2 : C 3 : under mast under power unit under frame Grade clearance The angle (α) between the plane contacting the front tires and passing the front lower end of the mast and ground is called the “Approach angle”. The angle (β) between the plane contacting the rear wheels and passing the rear lower end of the forklift truck and ground is called the “Departure angle”. The angle (γ) between the lane intersecting on the underside parts of the body where the first plane is tangent to the front tires and the second plane is tangent to the rear tires is called “Ramp brakeover angle”. 7 Tailift Sales Manual 2005
These angles are essential for assessing the ability of a forklift truck to climb over an obstacle on the ground when traveling. Approach Angle Departure Angle Ramp break-over Angle Performance The performance of forklift truck is changed by road surface and oil temperature of the transmission or reduction gear etc. The value on this handbook shows on the concrete or asphalt road and oil temperature as below. Engine oil: more than 50 o C (122 o F) Transmission: more than 50 o C (122 o F) Torque converter: more than 80 o C (176 o F) Reduction gear: more than 50 o C (122 o F) Hydraulic tank: more than 40 o C (104 o F) Lifting/Lowering speed The speed of the forks as they move upwards and downwards is expressed both for their loaded state and unloaded state. The lowering speed has been limited (reduced) to prevent both vehicle instability and damage to the load which can result from sudden drops caused by the weight of the load. Travel speed The maximum truck speed when the accelerator pedal is fully opened. Drawbar pull The forklift truck is often used as a tractor for a trailer or other equipment. In such instances, the 8 Tailift Sales Manual 2005
Page 1 and 2: INDEX Glossary 1-3 Explanation of f
Page 3 and 4: Indicated horsepower: The horse pow
Page 5 and 6: Explanation of forklift terms Load
Page 7: Turning radius The radius of the lo
Page 11 and 12: Weight Truck weight: Total weight o
Page 13 and 14: 12 Tailift Sales Manual 2005
Page 15 and 16: Lift Truck Class I-VII Class I - El
Page 17 and 18: TAILIFT IC CUSHION MAST SPECIFICATI
Page 19 and 20: TAILIFT IC CUSHION MAST SPECIFICATI
Page 21 and 22: TAILIFT IC PNEUMATIC MAST SPECIFICA
Page 23 and 24: TAILIFT IC PNEUMATIC MAST SPECIFICA
Page 25 and 26: TAILIFT LPG AND DIESEL TRUCK WEIGHT
Page 27 and 28: TAILIFT LPG AND DIESEL TRUCK WEIGHT
Page 29 and 30: DUAL PNEUMATIC TIRES MODEL SIZE P.R
Page 31 and 32: English to Metric Conversion Factor
Page 33 and 34: DECIMAL EQUIVALENTS OF FRACTIONS 1/
Page 35 and 36: Grade in degrees and percent Degree
Page 37 and 38: Part 1 1. Maximum weight lifted kg
Page 39 and 40: 4. Product Data 4a. Type of Product
Page 41 and 42: 5. Towing consideration (if applica
Page 43 and 44: 8. Ventilation conditions Consider
Page 45 and 46: 11. Boxcar loading or unloading (if
Page 47 and 48: 13. Overhead Obstructions Maximum o
Page 49 and 50: 16. Ramp data (if not applicable, g
Page 51 and 52: Part 2 Bulk Storage Calculations Ai
Page 53 and 54: Right angle stack illustration (nor
Page 55 and 56: Right angle stack illustration (wid
Page 57 and 58: Intersecting aisle illustration A =
Page 59 and 60:
Summary Sheet 1.- Maximum weight li
Page 61 and 62:
6. PAYMENTS: Customer agrees to pay
Page 63 and 64:
Circle one answer from each questio
Page 65 and 66:
A. Visibility is improved. B. The t
Page 67 and 68:
Check at the beginning of each 8 ho
Page 69:
Engineering and Standards Informati
show all

Tailift Sales Manual - Worldwide Forklifts

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?