Tailift Sales Manual - Worldwide Forklifts

More documents

Recommendations

Info

Right angle stack calculations (wide load) Aisle width; use narrowest aisle in which truck must right angle stack products. See illustration on facing page 41 and formula below Truck specs and load solve for this number Clearance from formula B below (see chart below) Measured aisle mm + mm = or less than mm in + in Right angle stack formula B (wide load) in Determine if wide loads can be handled within available aisle clearance. When D is greater than 2Z – C -2R, then the aisle width =D + C +R + Y + required operator clearance 2 2 Note: For three wheel trucks, use formulas on page 38. Y = D - C - R 2 + ( A + B) 2 2 2 Required aisle width for truck specs + load = D + C + R + Y = 2 2 Insert above Clearance Chart Suggested minimum aisle /operator clearance chart 12192 mm / 40 ft long load - Add 1220 mm or 48 inches 9144 mm / 30 ft long load - Add 914 mm or 36 inches 6096 mm / 20 ft long load - Add 610 mm or 24 inches 3048 mm / 10 ft long load - Add 305 mm or 12 inches 1524 mm / 5 ft long load - Add 152 mm or 6 inches 1219 mm / 4 ft long load - Add 102 mm or 4 inches 53 Tailift Sales Manual 2005
Right angle stack illustration (wide load) A = Distance from center of drive wheel to face of fork B = The length of the load (always in line with the truck) C = The maximum width of the truck D = The width of the load (across the truck) R = Inner turning radius Y = Load Radius Z = Truck Radius 54 Tailift Sales Manual 2005
Page 1 and 2:
INDEX Glossary 1-3 Explanation of f
Page 3 and 4: Indicated horsepower: The horse pow
Page 5 and 6: Explanation of forklift terms Load
Page 7 and 8: Turning radius The radius of the lo
Page 9 and 10: These angles are essential for asse
Page 11 and 12: Weight Truck weight: Total weight o
Page 13 and 14: 12 Tailift Sales Manual 2005
Page 15 and 16: Lift Truck Class I-VII Class I - El
Page 17 and 18: TAILIFT IC CUSHION MAST SPECIFICATI
Page 19 and 20: TAILIFT IC CUSHION MAST SPECIFICATI
Page 21 and 22: TAILIFT IC PNEUMATIC MAST SPECIFICA
Page 23 and 24: TAILIFT IC PNEUMATIC MAST SPECIFICA
Page 25 and 26: TAILIFT LPG AND DIESEL TRUCK WEIGHT
Page 27 and 28: TAILIFT LPG AND DIESEL TRUCK WEIGHT
Page 29 and 30: DUAL PNEUMATIC TIRES MODEL SIZE P.R
Page 31 and 32: English to Metric Conversion Factor
Page 33 and 34: DECIMAL EQUIVALENTS OF FRACTIONS 1/
Page 35 and 36: Grade in degrees and percent Degree
Page 37 and 38: Part 1 1. Maximum weight lifted kg
Page 39 and 40: 4. Product Data 4a. Type of Product
Page 41 and 42: 5. Towing consideration (if applica
Page 43 and 44: 8. Ventilation conditions Consider
Page 45 and 46: 11. Boxcar loading or unloading (if
Page 47 and 48: 13. Overhead Obstructions Maximum o
Page 49 and 50: 16. Ramp data (if not applicable, g
Page 51 and 52: Part 2 Bulk Storage Calculations Ai
Page 53: Right angle stack illustration (nor
Page 57 and 58: Intersecting aisle illustration A =
Page 59 and 60: Summary Sheet 1.- Maximum weight li
Page 61 and 62: 6. PAYMENTS: Customer agrees to pay
Page 63 and 64: Circle one answer from each questio
Page 65 and 66: A. Visibility is improved. B. The t
Page 67 and 68: Check at the beginning of each 8 ho
Page 69: Engineering and Standards Informati
show all

Tailift Sales Manual - Worldwide Forklifts

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?