Machine Manual - Production Tool Supply

More documents

Recommendations

Info

MAINTENANCE SCHEDULE fill lube pump 1 fill drawbar lube 2 check coolant level change coolant 3 check machine level check gibs check backlash check belt tension check servo cabinet and console fans, clean filters daily weekly monthly 3 months 6 months yearly as req’d. replace servo cabinet and console filters 4 X X X X X X X X X X 1 -Mobil Vactra #2 (ISO 68) or equivalent 2 -Break-Free Synthetic Air Tool Oil (5W) or equivalent 3 -Valenite Turn Tech Blue Metalworking Fluid or equivalent 4 -See Anilam Manual Electrical Manual Anilam 6000i.doc Page 23 of 25
Renishaw Tool Probe Installation This will assist you in setting up and installing your Renishaw TS-27R tool probe on your Fryer milling machine with Anilam control. Make sure you read the instruction manual that came with the Renishaw probe and the Anilam manual pertaining to probing cycles. The probe has been pre-wired and tested on the Fryer machine at the factory. The manuals also can be downloaded in PDF format from either Renishaw.com or Anilam.com Installation should be completed at the customer’s facility. Follow these basic instructions referring to the manufacturers manuals for further details: 1. Find a suitable mounting location for the probe ( most common is the far right hand corner of the table ) The probe should be mounted with the stylus pointing up and towards the left, this will exit the cable to the right. The Stylus should be approximately ½ the largest tool diameter used from the positive limit in x axis and at the rearmost t-slot(as long as it is a couple inches from the y limit). A t-nut can be used to mount the probe base with a ½-13 socket head cap screw. Make sure the cable will not interfere with anything during machine operation. 2. Once the probe is securely mounted tram the probe within .0002” perpendicular and parallel to the machine slides. See Renishaw installation manual for further details. 3. Follow the Anilam instructions to set the parameters according to your installation. 4. Now you will need a tool with a known diameter to preset the tool presetter. You should use the Anilam G150 or tool probe calibration cycle. See the Anilam manual for further details. 5. Once the G150 cycle is accomplished a G53 fixture offset should be activated and set to the top of the part so that all other tool to be set with the G151 cycle will be referenced to the top of the part. Electrical Manual Anilam 6000i.doc Page 24 of 25
Page 1 and 2: FRYER MACHINE SYSTEMS MC 30-60 P ME
Page 3 and 4: maintenance MC P series.doc 3 OF 19
Page 7 and 8: ARM TOOL CHANGER NO PART NO. DESCRI
Page 9 and 10: X AXIS TABLE 49 1 50 9 51 2 52 3 10
Page 13 and 14: Leveling Procedure For VB or MC Mac
Page 15 and 16: Step 5 Now that the machine should
Page 17 and 18: High pressure pump adjuster - this
Page 19 and 20: Fill point for pump oil - Replace h
Page 21 and 22: Maintenance Manual Electrical and P
Page 23 and 24: STARTUP PROCEDURE FOR FRYER VB/MC S
Page 25 and 26: 70 Jon Barrett Road Robin Hill Corp
Page 27 and 28: PANEL LAYOUT Electrical Manual Anil
Page 29 and 30: Fryer Mill with Anilam 6000i Contro
Page 31 and 32: Tool Change Height Adjustment The p
Page 33 and 34: Arm Up/Down Ram 6 control solenoids
Page 35 and 36: CAROUSEL TOOL CHANGER Electrical Ma
Page 37 and 38: Electrical Manual Anilam 6000i.doc
Page 39 and 40: Electrical Manual Anilam 6000i.doc
Page 41: ANILAM 6000i M Codes This document

Machine Manual - Production Tool Supply

Create successful ePaper yourself

Delete template?

Save as template?