PROFIBUS-DP Option board SV-iS5,iP5A,iV5 - Ana-Digi Systems

More documents

Recommendations

Info

0x000F Trip Information - R 0x0010 Input Terminal Information - R 0x0011 Output Terminal Information - R 0x0012 Analog Input 1 - R Bit00 Over Current1(OCT U, V, W) Bit01 Bit02 Bit03 Bit04 Bit05 Bit06 Bit07 Bit08 Bit09 Bit10 Bit11 Bit12 Bit13 Bit14 Bit15 Bit00 Bit01 Bit02 Bit03 Bit04 Bit05 Bit06 Bit07 Bit08 Bit09 Bit10 Bit11 Bit12 Bit13 Bit14 Bit15 Bit00 Bit01 Bit02 Bit03 Over Voltage(OV) Not Used BX Low Voltage(LV) Fuse Open(FO) Ground Fault(GF) Inverter Over Heat(IOH) E-Thermal(ETH) Over Load(OLT) HW-Diag External-B(EXT-B) Over Current2 (Arm Short U, V, W) Option Error Encoder Error Inverter Over Load(IOLT) FX RX BX RST Not Used Not Used Not Used Not Used P1 P2 P3 P4 P5 P6 P7 Not Used 30A – 30C 1A – 1B 2A – 2B OC1 - EG Bit04~15 Not Used Analog Input 1( User Manual Ai1) -100.0%(FC17h).~.100.0%(03E8h)
0x0013 Analog Input 2 - R 0x0014 Analog Input 3 - R Analog Input 2(User Manual Ai2) -100.0%(FC17h) ~ 100.0%(03E8h) Analog Input 3(User Manual Ai3) -100.0%(FC17h) ~ 100.0%(03E8h) 0x0015 RPM - R Reverse speed is conservative operation of 1 Note13) 0x0017 Speed Cmd Hz R/W Note 14) SV-iV5 : Used in Device Net 0x001D Speed Cmd1 RPM R Target Speed Cmd 0x001E Speed Cmd2 RPM R Note 15) Ramp Speed Cmd 0x001F Speed control input Cmd RPM R Note 16) Speed controller Reference speed 0x0020 Motor Speed RPM R Note 13) 0x0021 Torque Reference 0.1% R Note 17) Torque Reference 0x0022 Torque Feedback 0.1% R Note 18) Torque Feedback 0x0023 No-load Current 0.1% R Percentage of PAR_26 Flux-Curr (Read Under driving : Refer to 0x050A Note 32) ) 0x0024 PID Reference 0.1% R Note 19) PID Reference 0x0025 PID Feedback 0.1% R Note 20) PID Feedback 0x0026 PID Output 0.1% R Note 21) PID Output 0x0027 Inverter Temp deg R Inverter Temp 0x0028 Line Speed 0.1% R Note 22) Motor speed when WEB Control 0x0029 Diameter 0.1% R Calculated diameter when WEB Control Note 23) Note 24) 0x002A Tension output 0.1% R Tension output when WEB Control 0x002B Dancer Input 0.1% R Note 25) Dancer Input when WEB Control 0x002C Taper Input 0.1% R Note 26) WEB Control 시 Taper Input Note 6) In case of acceleration/deceleration time they were used in the same address, as the addresses of 0x0007 and 0x0008 are used by the other types (iS5, iG5…etc) in the device net. In case of SV-iV5 in fact, you may use acceleration/deceleration time of the addresses for 0x0503, 0x0504 in the rest except the device net. Note 7) Only when using the device net, Frequency(Hz) is displayed for the motor speed feedback during communication. Note 8) Negative output is calculated in 2's complement. For the calculation method, please refer to Note 17. Note 9) It indicates the state where the inverter can be operated without trip. In this case, it indicates the all the states during operation, before and after operation as ‘1’. Note 10) It indicates each state as follow; Stop (bit 0=‘1’) as ‘0’, Rotating in Forward Direction during Operation as ‘1’, Rotating in Reverse Direction during Operation as ‘0’. In case of connection error, it indicates as follows; Rotating in Forward Direction during Operation as ‘0’, Rotating in Reverse Direction during Operation as ‘1’.. Note 11) Relationships between Bit10 Forward Direction Command / Bit11 Reverse Direction Command, and Bit01 Forward Direction Operation (FX) / Bit02 Reverse Direction Operation (RX) are as follows: Bit10 and Bit11 show current operation command information, while Bit01 and Bit02 show current operation state. For example, in case of inputting stop command during forward direction operation, Bit11 forward direction command becomes ‘0’, but Bit01 forward direction operation (FX) becomes ‘1’ during deceleration and ‘0’ after stop mode. For the other example, in case of inputting reverse direction operation command during forward direction 1800 RPM operation, it conducts deceleration at 1,800 RPM and Bit11 Reverse Direction
Page 1 and 2: User Manual PROFIBUS-DP Option boar
Page 3 and 4: 1. INTRODUCTION By using a Profibus
Page 5 and 6: 2.1.3 Terminal resistor setting Con
Page 7 and 8: 3 I/O Data Transmit/Receive Output
Page 9 and 10: Parameter Address Parameter Name Un
Page 11 and 12: 5210 FU1 #16 Flux Force 1000 5000 1
Page 13 and 14: 5335 FU2 #53 PID I-time 300 320 0 0
Page 15 and 16: EXT Group > Address No. Parameter D
Page 17 and 18: 5708 APP #08 Aux Mot Run 0 4 0 5709
Page 19 and 20: 7.2 SV-iP5A Parameter Code 7.2.1 Co
Page 21 and 22: Address Parameter Unit Unit R/W Dat
Page 23: 7.3. SV-iV5 Parameter Code 7.3.1 Co
Page 27 and 28: process PID output controller verif
Page 29 and 30: 599.9sec(176Fh). In order to set ov
Page 31 and 32: Ki1(0x7C20), WEB_37 ProcPID Kd(0x7C

PROFIBUS-DP Option board SV-iS5,iP5A,iV5 - Ana-Digi Systems

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?