Advantage GPX 33 - Paint Sprayers, HVLP Sprayers, Powered Rollers

More documents

Recommendations

Info

StartCleanupMINERALSPIRITSorYou will need:• A water source that can be delivered witha garden hose (latex materials only)• Mineral spirits if using oil-based material• Empty waste container• A container with warm, soapy waterCleaning notes - read before cleaning• When using latex material, clean sprayer and components with warm, soapy water. For oil based material usemineral spirits. Never use mineral spirits with latex materials.• NEVER use gasoline to clean sprayer.• Dispose of used cleaning solution properly.• Thorough cleaning and lubrication of sprayer is important to ensure proper operation after storage.• If you flush your sprayer with mineral spirits, repeat Cleanup instructions using warm, soapy water.Follow these steps whenever cleaning with mineral spirits:• If spraying or cleaning with oil-based materials, the spray gun must be grounded while preparing the spray hose orcleaning.• Ground the gun by holding it against the edge of a metal container while purging. Failure to do so may lead to astatic electric discharge which may cause a fire.• Always flush spray gun at least one hose length from spray pump.• If collecting flushed solvent in one gallon metal container, place it into an empty five gallon container, then flush.• Area must be free from vapors.• Follow all cleanup instructions.Cleanup - Latex materialsSTOPFollow these steps if you used latex materials and if you have agarden hose available. If you do not have a garden hose available,follow the Cleanup - Oil-Based Materials instructions on page 18.1 23 4SPRAYPRIME1. Perform Pressure Relief Procedure(page 7).2. Remove the spray tip andplace into container filledwith warm, soapy water.3. Place the suction tube and return tubeinto an empty waste container.4. Using a garden hose, rinse off thesuction tube, return tube and inlet filter.Empty the waste container of all fluids.English16
5 6 7 85. Remove the inlet filter fromthe suction tube and placeit into waste container.6. Thread pump cleaningadapter onto garden hose.Thread suction tube fittingover the adapter.7. Unclip the return tube from the suction tubeand place it into the waste container. Turnthe PRIME/SPRAY knob to PRIME.8. Turn the water supply to the garden hose on.Start the engine (see page 4).Water will go into the suction tube and outthrough the return tube. Let the pump runfor a few minutes, and leave pump runningfor next steps.9SPRAYSPRAYPRIME10 11 12SPRAYPRIMEPRIME9. Point the spray gun at the side ofa waste container.10. While squeezing the trigger, turn thePRIME/SPRAY knob to SPRAY.11. Continue squeezing the triggeruntil fluid is coming out clear.12. Perform Pressure ReliefProcedure, page 7.Move on the Cleaning the SprayGun Components, page 19.17English
Page 5 and 6: Proper useand functionsSPRAYPRIMEPR
Page 7 and 8: Pressure Safety ReliefProcedure**Pe
Page 10 and 11: Start4. PracticeSprayingYou will ne
Page 12 and 13: SprayingTroubleshooting -Clear theS
Page 14 and 15: SprayingTroubleshooting -Clean theI
Page 18 and 19: Cleanup -Oil-BasedMaterials1 2 3SPR
Page 20 and 21: Long TermStorage1 2OILHOUSEHOLDStar
Page 22 and 23: TroubleshootingBefore servicing, al
Page 25 and 26: Parts List • Liste de Pièces •
Page 27 and 28: Parts List • Liste de Pièces •
Page 29: Limited WarrantyAIRLESS PAINT SPRAY

Advantage GPX 33 - Paint Sprayers, HVLP Sprayers, Powered Rollers

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?