<strong>Motor</strong> <strong>Technology</strong> <strong>Ltd</strong> – control in motion.comEncoders - Lenord+Bauer MiniCODER, magnetic incremental kitMiniCODER’s are designed <strong>for</strong> installation in drivesas an alternative to the conventional encoders.They are contact-less and are equipped with amagnetic scanning system, which, in conjunction witha toothed wheel as measuring scale, permit themeasurement of rotary motion. This solution isexceptionally space saving.The Lenord+Bauer MiniCODER has developed, overa number of years, into a range of magnetic and halleffectkit encoders <strong>for</strong> applications as diverse asautomatic wood cutters, speed sensors <strong>for</strong> railvehicles and ships, and high-speed machine toolspindles to name a few.The contact-free sensing principle allows <strong>for</strong>measurement of speed and position, without limitingper<strong>for</strong>mance due to bearings, housings, shaft seals,etc.MiniCODER have been tried and tested inapplications up to 70,000RPM.The sensor elements, the magnet and the integratedelectronic system are incorporated in state-of-the-art microsystem technology and are fully encapsulated.The design together with subsequent circuitry ensures anelectrically and mechanically robust product.Features• Robust system <strong>for</strong> harshest conditions• Interpolation of each tooth up to 40 times.• Maintenance-free, non wearing / ageing• Dew-point-proof• Insensitive to dirt, shock and vibration• High IP rating• High operating temperature range• Installation on shafts with diameters ranging from 8 mmto more than 500 mmTechnical Data GEL 243 GEL 244 GEL247 series GEL 248Motion detection Rotary, linear Rotary Rotary RotaryMax. air gapModule M /pitch P0.3 mmM = 0.5 up to 1P = 1.0 / 1.6 / 2.0Dependent on module0.15 mmDependent on module3 mmDependent on module0.8 mmM = 0.3 / 0.5 M = 1.0 ... 3.5 M = 1.0 up to 3.5Frequency range 0...200 kHz 0...200 kHz 0...25 kHz 0...25 kHzMeasuring scaleTooth-wheel, measuringrod or piston rodTooth-wheelTooth-wheel orslotted diskTooth-wheelTemperature range -20 ... + 85°C -40 °C ... +120 °C -40 °C ... +120 °C -40 °C ... +120 °CProtection class IP 67 IP 68 IP 68 IP 68Supply voltage 5V DC 5V DC 10 ... 20V DC 10 ... 30V DCOutput signalsSquare-wave 5V Track A, B, N, A/, B/, N/,Square-wave 10 ... 30 VSquare-waveSin/Cos 1V ppSine-wave 1 V ppDCSpeed and positiondetection in high-speedspindles, angleFields of applicationmeasurement in radarequipmentMounting in motors,gearboxes, andpneumatic & hydrauliccylinders.Safety integrated" <strong>for</strong>Siemens numeric controlsRail vehicles,measurement of speedand positions in machinesand motorsAutomatic doors,escalators, <strong>for</strong>klift trucks,cranes and specialvehiclesThe above is sample in<strong>for</strong>mation on the product range. Please contact us <strong>for</strong> a full brochure . . .Page 22 Call 0161 217 7100 or email us at info@controlinmotion.com <strong>for</strong> further details Doc. MT-sfc-3/09
<strong>Motor</strong> <strong>Technology</strong> <strong>Ltd</strong> – control in motion.comGearboxes – EP 55...155, general purpose planetaryThe EP gearboxes are general-purpose units suitable<strong>for</strong> use with servo, stepper and standard AC and DCmotors. The robust construction using steel housings,shafts and gears offer high torsional stiffness andoverload capability.The EP gearboxes offer medium backlash,mathematically accurate ratios up to 100:1 and highefficiency.Features• Backlash less than 15’ single and 20’ two stage• Input speeds up to 5000rpm• Low noise (