'UDLQDJH DQG 6HZDJH À :DVWH :DWHU 7UDQVSRUW ... - WILO

Planning guideCeram coatingCeram C3 - Technical dataDescriptionCeram C3 is a high-performance composite material for repairing andprotecting all metal surfaces which are subject to abrasion, corrosion,cavitation and chemical exposure. Ceram C3 is applied with a coatingthickness of 3 mm. It does not shrink and consists almost entirely ofsolids. Ceram C3 contains a high percentage of carbides for use underextremely abrasive operating conditions which involve complex andexpensive repair measures. The material can either be used forrestoring abraded metal surfaces or as a preventive coating which issuperior to the original metal with regard to abrasive strength. CeramC3 can be used instead of metal applications, rubber fillers, etc.CompositionPolymer/aluminium oxide composite material made of a base compoundand reinforcement.Base compound: A modified polymer made up of two parts with analiphatic hardening agent.Reinforcement: A mixture (protected by proprietary rights) made upof aluminium oxide and silicon carbide particles.This mixture has excellent abrasion resistance and can be appliedvery easily.Properties• Excellent abrasion resistance ensures long operation and usually lastslonger than a welded-on metal coating.• Its tough synthetic resin structure is resistant to temperature shocksand impact.• Excellent adhesion ensures reliability and prevents stripping.• Simple application reduces work expenses and downtimes.• Withstands varying chemical operating conditions when metals fail.• Can be easily moulded to any metal surface.• Practical 1.7:1 weight and volume mixture ratio.Technical dataHardness Shore D 90Density ASTM D 792 1.87 g/cm 3Shrinkage during hardening ASTM D 2566 0 mm/cmTensile shear resistance ASTM D 1002 17 N/mm 2Tensile strength / ultimate ASTM D 638 29.7 N/mm 2strainCompressive strength ASTM D 695 103 N/mm 2Bending strength ASTM D 790 69 N/mm 2Adhesive strength / steel ASTM C 633 15.9 N/mm 2Impact resistance / strength ASTM D 256 12 J/mLinear expansion coefficient ASTM D 696 61.8 x 10 -61 1/KElectrical resistance ASTM D 257 8 Ohm cmThermal conductivity ASTM C 177 0.75 w/m x KDielectric strength ASTM D 149 13.4 kV/mmTemperature resistance, dry ASTM D 648 190 °CTemperature resistance, wet ASTM D 648 65 °CResistance tableFluidFactorAcidsSulphuric acid (10%) 1Sulphuric acid (20%) 2Hydrochloric acid (5%) 1Hydrochloric acid (10%) 2Hydrochloric acid (20%) 3Acetic acid (5%) 2Acetic acid (10%) 4Bases and bleachesCaustic soda (10%) 1Caustic soda (30%) 1Ammonium hydroxide (28%) 1Potassium hydroxide (10%) 1Potassium hydroxide (50%) 1Other compoundsIsopropyl alcohol 1Kerosene 1Naphtha 1Salt water 1Sewage 1Toluene 1Xylene 1Bunker C 1Diesel 1Tested at 20 °C. Sample hardened for 7 days at 20 °C. Longer hardeningimproves the chemical resistance.Key: 1 = stable; 2 = stable, short-term; 3 = overflow-stable, immediatecleaning; 4 = not recommended for direct contact36 Wilo Water Management catalogue – 50 Hz – Drainage and sewage – Waste water transport and dewatering – Edition 2012 – Subject to change without prior notice