2 - vonRoll hydro

More documents

Recommendations

Info

Accessories for push-in joint pipingPressure pipes and adapter fittingsAccu screwdriver PIW 14.4SD Fig. 294weightkg2.1 -Technical data14.4.Volt / 1.4 – 2.4 AhIdling speed 0 –2200 rpmHammer 0-2500 blows/minTorque 158 NmWeight – without accu-pack 1.6 kgWeight with accu-pack 2.1 kgLength 193 mmChuck 1/2" squareStandard scope of supply:2x 14.4 V / 1.4 Ah NiCd flatpack accu-packRCA 7224MB chargerABS system caseM20 hexagonal socket-wrench insertitem-no.451400suissetec-Subject to alteration without noticephone +41 62 388 14 00, fax +41 62 388 14 20, www.vonroll-hydro.ch, info@vonroll-hydro.ch 2/11.4
Installation instructions for push-in joint piping1. General remarksFollowing the instructions below will guaranteeprofessional and correct installation work.2. Removal of caps and dummy plugsOnly remove caps and dummy plugs on-site just before the pipe is laid.2Environmental protection:The caps and dummy plugs are designed to be one-way material.They are made of environment-friendly plastics (green polyethylene andblack ethylene-propylene).A practical way to reuse them is to use them as a protective cushionbetween the pipe body and trench bottom or levelling (e.g. cement slabs).If they are disposed of in an appropriate waste incineration plant,no poisonous or corrosive pollutants are produced.3. Cleaning the socketsCheck that the insides of the socket around the retainer groove (A) andthe sealing chamber (B) are clean.For ducpur ® pipes, bitumen residue and/or other deposits can beremoved using the groove scraper.ecopur ® pipes, adapter fittings and slide-valves are only to becleaned with a cloth.The use of groove scrapers is forbidden.4. Lubricating the socketsUsing a brush, apply the lubricant specially suitable for push-in jointconnections to the sealing chamber (B).The retainer groove (A) should not be lubricated.Subject to alteration without noticephone +41 62 388 14 00, fax +41 62 388 14 20, www.vonroll-hydro.ch, info@vonroll-hydro.ch 2/12.1
Page 1: Pressurised piping and fittingsfor
Page 5 and 6: IntroductionPiping systemsAs one of
Page 7 and 8: Ductile cast ironMaterial character
Page 9 and 10: Resistance to chemicals - Acidic or
Page 11 and 12: Permissible operating pressures for
Page 13 and 14: StandardsEN 545Pipes, adapter fitti
Page 15 and 16: Push-in joint products 2FigurePaged
Page 17 and 18: Pressure pipe with push-in socketPr
Page 19 and 20: Sewage pipe with push-in socketSewa
Page 21 and 22: Pressure pipe with push-in socketPr
Page 23 and 24: Adapter fittings with push-in joint
Page 35 and 36: Push-in joint connectionsPressure p
Page 37 and 38: Push-in joint connectionsPressure p
Page 39 and 40: Accessories for push-in joint pipin
Page 41 and 42: Accessories for push-in joint pipin
Page 43: Accessories for push-in joint pipin
Page 47 and 48: 7. Centring and alignment of push-i
Page 49 and 50: 8.6 Montage Assembly von of shorten
Page 51 and 52: Fit - Schubsicherungsring the thrus
Page 53 and 54: - Zentrieren analog Pkt. 7 und mit
Page 55: Flanged products 4FigurSeiteducpur
Page 58 and 59: Pressure pipe with flangesPressure
Page 70 and 71: Adapter fittings with flangesPressu
Page 86 and 87: 6. Remarks concerning the installat
Page 89 and 90: Tapping clampsPressure pipes and ad
Page 91: Planning and finishing work 6PageCu
Page 94 and 95:
6. Markings on push-in joint pipesT
Page 97 and 98:
RESICOAT ® RS Repair Material1. Us
Page 99 and 100:
Installation instructions forducpur
Page 101 and 102:
Information for planners and pipe f
Page 103 and 104:
3. Permissible pressures3.1 Pressur
Page 105 and 106:
4. Table of flanges for ductile cas
Page 107 and 108:
5.2 Dimensions for two spigot/socke
Page 109 and 110:
7.2 Chart for pressure losses in wa
Page 111:
8.1 Area of applicabilityIn the DVG
Page 115 and 116:
Transport and storageGuidelines:For
Page 118:
vonRoll hydrotec ltd.von roll-stras
show all

2 - vonRoll hydro

Create successful ePaper yourself

Delete template?

Save as template?