VITOTRONIC 100, HC1 VITOCONTROL-S, WB2B Installation and ...

More documents

Recommendations

Info

General InformationImportant Regulatory and Safety RequirementsApprovalsViessmann boilers, burners andcontrols are approved for sale in NorthAmerica by CSA International.CodesThe installation of this unit shall be inaccordance with local codes. In theabsence of local codes, use:CSA C22.1 Part 1 and/or local codesin CanadaNational Electrical Code ANSI/NFPA70 in the U.S.Always use latest editions of codes.Please carefully read this manual priorto attempting installation. Anywarranty is null and void if theseinstructions are not followed.For information regarding otherViessmann System Technologycomponentry, please referencedocumentation of the respectiveproduct.We offer frequent installation andservice seminars to familiarize ourpartners with our products. Pleaseinquire.Working on the equipmentThe installation, adjustment, service,and maintenance of this product mustbe done by a licensed professionalheating contractor who is qualified andexperienced in the installation, service,and maintenance of hot water boilers.There are no user serviceable parts onthe boiler, burner, or control.Ensure main power supply toequipment, the heating system, and allexternal controls has been deactivated.Close main oil or gas supply valve.Take precautions in both instances toavoid accidental activation of powerduring service work.The completeness and functionality offield supplied electrical controls andcomponents must be verified by theheating contractor. These include lowwater cut-offs, flow switches (if used),staging controls, pumps, motorizedvalves, air vents, thermostats, etc.WARNINGTurn off electric powersupply before servicing.Contact with liveelectric componentscan cause shock orloss of life.Technical literatureLiterature applicable to all aspects ofthe Vitocontrol-S, WB2B:- Installation & Service Instructions- Operating & User Instructions- Instructions of other Viessmannproducts utilized and installed- Installation codes mentionedin this manualLeave all literature at the installationsite and advise the system operator/ultimate owner where the literaturecan be found. Contact Viessmann foradditional copies.5414 553 v1.46
General InformationImportant Regulatory and Installation RequirementsPower supplyInstall power supply in accordance withthe regulations of the authoritieshaving jurisdiction or, in the absence ofsuch requirements, in accordance withNational Codes. Viessmannrecommends the installation of adisconnect switch to the 120 VACpower supply outside of the boilerroom. The installer must providemaximum 15 A overcurrent protectionfor the 120 VAC power supply (fuse orcircuit breaker).Working with an open controlNo static discharge to the internalcomponentry must ever occur whenworking with opened controlequipment.About these Installation InstructionsTake note of all symbols and notations intended to draw attention to potential hazards or important product information.These include ”WARNING”, ”CAUTION”, and ”IMPORTANT”. See below.WARNINGIndicates an imminently hazardoussituation which, if not avoided, couldresult in death, serious injury orsubstantial product/property damage.CAUTIONIndicates an imminently hazardoussituation which, if not avoided, mayresult in minor injury orproduct/property damage.IMPORTANTWarnings draw your attention to thepresence of potential hazards orimportant product information.Cautions draw your attention to thepresence of potential hazards orimportant product information.Helpful hints for installation,operation or maintenance whichpertain to the product.This symbol indicates that additional,pertinent information is to be found incolumn three.This symbol indicates that otherinstructions must be referenced.5414 553 v1.47
Page 1 and 2: Installation andService Instruction
Page 3 and 4: 3Table of ContentsIndexPageGeneral
Page 5: Table of ContentsIndex (continued)C
Page 9 and 10: Heating system designsSystem design
Page 11 and 12: Installation - Vitocontrol-S, WB2BI
Page 13 and 14: Installation - Vitocontrol-S, WB2BS
Page 15 and 16: Installation - Vitocontrol-S, WB2BM
Page 21 and 22: Installation - Vitocontrol-S, WB2BC
Page 23 and 24: Installation - Vitocontrol-S, WB2BC
Page 25 and 26: Installation - Vitocontrol-S, WB2BM
Page 27 and 28: Installation - Vitocontrol-S, WB2BO
Page 29 and 30: Initial start-upFurther step-by-ste
Page 39 and 40: Service scanning - Vitotronic 100,
Page 41 and 42: Service scanning - Vitotronic 100,
Page 43 and 44: Service scans - Vitocontrol-S, WB2B
Page 45 and 46: 5414 553 v1.4Scan123Scan88Display a
Page 47 and 48: Troubleshooting - Vitotronic 100, H
Page 49 and 50: Troubleshooting - Vitotronic 100, H
Page 51 and 52: Troubleshooting - Vitocontrol-S, WB
Page 53 and 54: CCTroubleshooting - Vitocontrol-S,
Page 55 and 56: Troubleshooting - Vitocontrol-S, WB
Page 57 and 58:
Function description - Vitotronic 1
Page 59 and 60:
Function description - Vitocontrol-
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Components - Vitocontrol-S, WB2BCom
Page 71 and 72:
Components - Vitocontrol-S, WB2BMix
Page 73 and 74:
Components - Vitocontrol-S, WB2BRem
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Components - Vitocontrol-S, WB2BRoo
Page 81 and 82:
Coding - Vitotronic 100, HC1Resetti
Page 83 and 84:
Coding - Vitotronic 100, HC1Coding
Page 85 and 86:
Coding - Vitocontrol-S, WB2BCoding
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Coding - Vitocontrol-S, WB2BSlab cu
Page 105 and 106:
Connection and wiring diagrams- Vit
Page 107 and 108:
Connection and wiring diagrams- Vit
Page 109 and 110:
Connection and wiring diagrams - Vi
Page 111 and 112:
Connection and wiring diagrams - Vi
Page 113 and 114:
AppendixParts ListVITOCONTROL-S, WB
Page 115 and 116:
1155414 553 v1.4
show all

VITOTRONIC 100, HC1 VITOCONTROL-S, WB2B Installation and ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?