4049-229C EDV Series.indd - At Andiron Fireplace Shop

More documents

Recommendations

Info

2. Top Vent - Vertical Termination - (continued) 28 Three Elbows Figure 7.9 12 ft (3.66 m) min. 60 ft (18.29 m) max. Maximum horizontal run is 100% of vertical, but cannot exceed 26 ft (7.92 m) Heatilator • Eclipse • <strong>4049</strong>-229 Rev C • 06/08
8 Vent Clearances and Framing A. Pipe Clearances to Combustibles WARNING! Risk of Fire! Maintain air space clearance to vent. DO NOT pack insulation or other combustibles: • Between ceiling fi restops • Between wall shield fi restops • Around vent system Failure to keep insulation or other material away from vent pipe may cause over heating and fi re. Note: Heat shields MUST overlap by a minimum of 1 1/2 in. (38 mm). • SLP heat shield - designed to be used on a wall 4-3/8 in. to 7-5/8 in. (111 mm to 194 mm thick). • If wall thickness is less than 4-3/8 the existing heat shields must be field trimmed. If wall thickness is greater than 7-5/8 in. an extended heat shield will be required. Drywall 1 in. (25 mm) 2 x 4 or 2 x 6 header 3 in. (76 mm) WALL Air space clearance to bottom and sides of horizontal pipe must be at least 1 in. (25 mm) No combustible framing to be located within shaded area. 3/4 in. (19 mm) minimum to perpendicular wall. * When using SLP pipe, minimum clearances from the vent pipe to combustible materials at inside wall firestops are: Top: 2-1/2 in. (64 mm) Bottom: 1/2 in. (13 mm) Sides: 1 in. (25 mm) Figure 8.1 Horizontal Venting Clearances To Combustible Materials B. Wall Penetration Framing Combustible Wall Penetration Whenever a combustible wall is penetrated, you must frame a hole for the wall shield fi restops. A wall shield fi restop maintains minimum clearances and prevents cold air infi ltration. • The opening must be framed on all four sides using the same size framing materials as those used in the wall construction. • A wall shield fi restop must be placed on each side of an interior wall. A minimum 1 1/2 in. (38 mm) overlap of attached heat shields must be maintained. • See Section 10.L. for information for regarding the installation of a horizontal termination cap. Non-Combustible Wall Penetration If the hole being penetrated is surrounded by noncombustible materials such as concrete, a hole with diameter one inch greater than the pipe is acceptable. Whenever a non-combustible wall is penetrated, the wall shield fi restop is only required on one side and no heat shield is necessary. 10 in. [254mm] The center of the framing hole is 1 in. [25mm] above the center of the horizontal vent pipe. Framing should be constructed of 2 X 4 lumber or heavier. Figure 8.2 Wall Penetration 10 in. [254mm] Vent framing hole 36 1/2 in. [927 mm] (Center of pipe) Heatilator • Eclipse • <strong>4049</strong>-229 Rev C • 06/08 29
Page 1 and 2: Model(s): EDV3633, EDV3633I, EDV363
Page 3 and 4: Safety Alert Key: • DANGER! Indic
Page 5 and 6: B. Limited Lifetime Warranty Gas Ap
Page 7 and 8: Note: The following requirements re
Page 9 and 10: C. Fan Kit • Optional • Contact
Page 11 and 12: I. Lighting Instructions (Standing
Page 13 and 14: 3 Maintenance and Service Any safet
Page 15 and 16: (Either cobrahead or SIT) PRODUCT S
Page 17 and 18: B. Design and Installation Consider
Page 19 and 20: B. Constructing the Appliance Chase
Page 21 and 22: 6 A. Vent Termination Minimum Clear
Page 23 and 24: 7 Vent Information and Diagrams A.
Page 25 and 26: 1. Top Vent - Horizontal Terminatio
Page 27: 2. Top Vent - Vertical Termination
Page 31 and 32: D. Install Attic Insulation Shield
Page 33 and 34: 10 Installing SLP Vent Pipe A. Asse
Page 35 and 36: E. Installing Metal Roof Flashing N
Page 37 and 38: G. Installing Vertical Termination
Page 39 and 40: Install Horizontal Termination Cap
Page 41 and 42: 12 Electrical Information A. Wiring
Page 43 and 44: F. Junction Box Installation If the
Page 45 and 46: B. Facing Material • Metal front
Page 47 and 48: • Place a small amount of 1/2 in.
Page 49 and 50: 15 Troubleshooting With proper inst
Page 51 and 52: B. Intellifi re Ignition System Sym
Page 53 and 54: 16 Reference Materials A. Appliance
Page 55 and 56: B. Vent Components Diagrams (contin
Page 57 and 58: C. Service Parts (continued) Servic
Page 59 and 60: This page intentionally left blank.

4049-229C EDV Series.indd - At Andiron Fireplace Shop

Create successful ePaper yourself

Delete template?

Save as template?