Chapter 7 - Veterinary Instrumentation

7 TRAUMA IMPLANTS & INSTRUMENTSInstrumentationCruciate Screwdriver Insert1.0MM CRUCIATE SCREWDRIVER INSERTThe Cruciate Head 1.0mm Screwsare very small and require adedicated Cross Head ScrewdriverTip. The tip of the Screwdriver has ataper fit which holds the screwwithout a sleeve.SDIN1.0 Screwdriver Insert for 1.0mm Screws £49.50Drill Bits 0.7mm and 1.0mm1.0mm Plate Bending IronsPlate bending irons — the small size of these implants necessitatesequally small plate bending irons. These have been designed withadditional slots to allow a degree of contouring across a plate’s width.1.0MM PLATE BENDING IRONS001280 1.0mm Plate Bending Irons £60.001.0mm Drill GuideUse a 0.7mm Drill Bit for a pilot hole and a 1.0mm Drill Bit for lagscrewing. At this size, these drills are very delicate and most power toolsare too heavy to provide adequate control to prevent breakages. Ourstep drills have the same shaft as our cruciate screwdriver insert for usein our lightweight modular screwdriver.DRILL BITS 0.7MM AND 1.0MM10MDB07 0.7mm Drill Bit £39.5010MDB10 1.0mm Drill Bit £39.501.0mm Modular Screwdriver HandpieceThe drill guide locates the drill, avoiding impingement on other implants.The drill guide additionally protects the soft tissues from drill ’wraparound’. One end takes the pilot drill 0.7mm and the other takes theclearance drill 1.0mm.1.0MM DRILL GUIDECDTIS10 1.0mm Drill Guide £110.00Small Compound Action Implant CuttersThe Modular Screwdriver Handpiece accepts the Cruciate ScrewdriverTip and the two sizes of Drill Bits. Its light weight combines with arotating end-cap allowing for more controlled, truer axial motionminimising breakages.1.0MM MODULAR SCREWDRIVERSDH1.0 1.0mm Modular Screwdriver Handpiece £145.001.0mm Plate Holding ForcepsHolding and manipulating these very small implants is difficult in agloved hand. We recommend the use of our Plate Forceps. The PlateForceps also make it easy to remove the plates from their slots in ourplate tray. The top jaw of the plate forceps has a locating projectionwhich fits into a screw hole to reduce slippage. The bottom jaw has alow profile to slide between stacked plates. The crank of the tips makesthem particularly useful for offering a plate up to a bone.1.0MM PLATE HOLDING FORCEPSC1PHF 1.0mm Plate Holding Forceps £27.50Designed to cut up to 1.5mm hard wire, these Small Compound ActionImplant Cutters with T.C. Jaws produce clean and precise cuts andideally suited to the 1.0mm Kit. At only 170mm long, they fit nicely intothe 1.0mm Kit Box.SMALL COMPOUND ACTION IMPLANT CUTTERS001230 1.0mm Implant Cutters Compound Action 170mm £195.001.0mm Bone Holding Forceps and Pointed Reduction Forceps1.0mm Screw ForcepsThe Screw Holding Forceps are a shrunken tip version of the tongs usedfor our larger implants and are particularly useful at this size1.0MM SCREW FORCEPSSF1024 1.0mm Screw Forceps £22.50A range of scaled down forceps have been developed for used on bonesof 3-5mm diameter.1.0MM PLATING SET001218XS X Small Serrated Bone Holding Forceps 3mm Gape £65.00001218S X Small Serrated Bone Holding Forceps 5mm Gape £65.00001208M Miniature Fragment Forceps 135mm £72.50172