Chapter 7 - Veterinary Instrumentation

www.vetinst.comTRAUMA IMPLANTS & INSTRUMENTS 7Anti-skid DrillsDrill StopsH090104ASUnless a Bone Drill is driven at 90 degrees to the bone surface there is atendency for the Drill to ‘skid’ over the bone surface placing the holeinappropriately. The Anti-skid Drill has a special tip to bite into the bone atvirtually any useful angle, accurately predetermining the hole position.Made from hard multi use 420 stainless steel.Available in all useful sizes. 1.5, 2.0, 2.5, 2.7, 3.2, 3.5, & 4.5mmANTI-SKID DRILLSH090101AS Anti-Skid Drill 1.5mm 60mm long £24.50H090102AS Anti-Skid Drill 2.0mm 100mm long £24.50H090112AS Anti-Skid Drill 2.5mm 115mm long £24.50H090104AS Anti-Skid Drill 2.7mm 130mm long £25.50H090105SAS Anti-Skid Drill 3.2mm 130mm long £25.50H090106SAS Anti-Skid Drill 3.5mm 130mm long £25.50H090106SAS/L Anti-Skid Drill 3.5mm 180mm long £27.00H090108SAS Anti-Skid Drill 4.5mm 130mm long £27.00090117AS Drill Box with Anti-skid Drills (7) £235.00Cannulated DrillsPicture: Jean-Benoit LefebvreDrilling to a pre-measured depth can be a challenge even with a ‘C’ arm!A more reasonably priced option is to use a Drill Stop which is tightenedonto the Drill Bit at the required depth. The Set includes 4 Stops to coverall the standard Drill Sizes.2.0, 2.5, 2.7, 3.2, 3.5 & 4.5mmThe Stop is tightened onto the Drill Bit using the Hex Driver provided.DRILL STOP SETDRILLSTOP Drill Stop Set in Stainless Case £105.00Mini Drill BitsIn stainless steel - hard.DRILL BITS - DENTAL FITD090100 0.052 (dia in.) 1.1 (dia mm) £62.50D090101 1.5 £65.00D090102 2.0 £67.50Drill Bits 0.7mm and 1.0mmUse a 0.7mm Drill Bit for a Pilot Hole and a 1.0mm Drill Bit for LagScrewing. At this size, these Drills are very delicate and most powertools are too heavy to provide adequate control to prevent breakages.Our Step Drills have the same shaft as our Cruciate Screwdriver Insertfor use in our lightweight Modular Screwdriver.DRILL BITS 0.7MM AND 1.0MM10MDB07 0.7mm Drill Bit £39.5010MDB10 1.0mm Drill Bit £39.50For maximum control over the alignment of bone tunnels use ofCannulated Drills is preferred. A Fine Guide Wire is drilled throughwhere the bone tunnel or screw hole is required. Only when the surgeonis satisfied that the guide wire is correctly positioned is the Drill drivenalong the Wire to create the hole. The Guide Wire can be repositioned ifnecessary without causing undue trauma to the bone.Available for Jacobs Chuck or AO Quickfit.CANNULATED DRILLSH090112CAN 2.5mm 130mm long 1.1mm Cannulation £65.00H090104CAN 2.7mm 130mm long 1.1mm Cannulation £65.00H090106CAN 3.5mm 130mm long 1.1mm Cannulation £65.00S090112CAN 2.5mm 130mm long 1.1mm Cannulation AO Quickfit £75.00S090104CAN 2.7mm 130mm long 1.1mm Cannulation AO Quickfit £75.00S090106CAN 3.5mm 130mm long 1.1mm Cannulation AO Quickfit £75.00090065 Guide Wire 1.1mm x 178mm (pack of 10) £27.50Drill CaseFolding Box to fit all the standard sizes of Drill. Ideal forautoclaves. Case has holes for 1.1, 1.5, 2.0, 2.5, 2.7,3.2, 3.5, 4.0, 4.5, and 5.5mm Drills.DRILL CASE090115S Drill Box S/Steel Empty (for I/Q Drills) £105.00090116 Drill Box S/S Complete with I/Q Drills (9) £165.00090115H Drill Box for Hard Drills Empty £105.00090117 Drill Box Complete with Hard Drills (10) £265.00090114AS Drill Box for Anti-Skid Drills Empty £105.00090117AS Drill Box Complete with Anti-Skid Drills (7) £235.00S090115 Drill Box for AO Drills Empty £105.00S090SET Drill Box Complete with AO Drills (10) £325.00213