FLENDER gear units - DS TECH

More documents

Recommendations

Info

© Siemens AG 2011Options for installation and attachment partsHousing torque arm (single arm)■ Dimensioned drawingscG 10G 2Ø 60aaD1G_MD30_XX_00099bGear unitsizesNominal outputtorqueT 2NNmDimensions in mmD 1 G 2 G 10 a b c Weight,approx.30 10000 375 132 25 55 225 435 12.535 15000 425 115 25 60 240 480 1537 20000 450 122 25 70 260 555 18.540 25000 480 125 35 80 310 690 2945 35000 540 135 35 90 330 725 3250 45000 585 135 35 110 430 905 4955 65000 670 185 35 130 410 1065 7260 80000 695 206 35 130 500 1065 72kg(450) 655-7447info@pt-dstech.comwww.dstech.ca8In the case of shaft-mounted gear units with a torque arm, the connection between the torque arm and foundation must always permitthe gear unit to move in accordance with the bearings of the machine shaft, without constraining forces acting on the gear unit.Ordering informationWhen ordering the housing torque arm, -Z should be added to the order number.Data position of the Order No. 1 to 6 7 8 9 10 11 12 13 14 15 16 Order codeOrder No. 2LP069 . - 0 . . . . - . . . . -ZHousing torque arm (single arm)Prepared for mounting a housing torque arm (single arm)M10M11Mounting of a twin housing torque arm is supported as standard.If a single housing torque arm is used, special bearings are required.This is also necessary if the housing torque arm is not included in the order, but the customer plans to use it.If a single housing torque arm is used, compliance with the minimum dimension c for the length of the lever arm is essential.1275 Newton, local 15Boucherville, Qc,Canada, J4B 5H28/2 Siemens MD 31.1 · 2011
Appendix© Siemens AG 201199/2 Partner at Industry Automation andDrive Technologies9/3 Online Services9/3 Information and Ordering in the Internetand on DVD9/4 Service & Support9/4 The unmatched complete service for theentire life cycle9/6 Knowledge9/7 Subject index9/8 Conditions of sale and deliveryExport regulations(450) 655-7447info@pt-dstech.comwww.dstech.ca1275 Newton, local 15Boucherville, Qc,Canada, J4B 5H2Siemens MD 31.1 · 2011
Page 1 and 2: © Siemens AG 2011FLENDER SIPStanda
Page 4: © Siemens AG 2011Answers for indus
Page 9 and 10: © Siemens AG 2011Technical informa
Page 11 and 12: © Siemens AG 2011Selection of the
Page 17: © Siemens AG 2011Selection of the
Page 20 and 21: Selection of the gear units© Sieme
Page 22 and 23: © Siemens AG 2011Flange-mounted ge
Page 28 and 29: Gear unit combinations© Siemens AG
Page 34 and 35: Connection dimensionsCylindrical sh
Page 36 and 37: Connection dimensionsHollow shafts
Page 38 and 39: Connection dimensions© Siemens AG
Page 40 and 41: Options for operationShaft sealsRad
Page 44 and 45: © Siemens AG 2011AppendixPartner a
Page 46 and 47: AppendixService & SupportThe unmatc
Page 48 and 49: AppendixService & Support© Siemens
Page 50 and 51: Appendix© Siemens AG 20119Conditio
Page 52: © Siemens AG 2011(450) 655-7447inf

FLENDER gear units - DS TECH

Create successful ePaper yourself

Delete template?

Save as template?